[ Log In ]
[ Register ]

Question #: 15004

Question: Will breakout-Mach3-USB-Board work in Windows ?

Current Solution

Absolutely. The mach3 USB will work in all versions of Windows and will also work in 32-bit or 64-bit mode.

If you have heard that Mach3 in general will not work in some versions of windows, it is because past controllers used parallel ports, and MAch3 needed to use a specific driver that only works under 32-bit mode. The MAch3 USB controller uses a traditional USB port, so you will have no problem with any version of Windows.

Respond:

Other Possible Solutions to this Question

  • WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

    no, it will only work on anodized aluminum

    Click the link to add information to this solution:
    WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

  • I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

    If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

    Click the link to add information to this solution:
    I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

  • WE HAVE PORTER CABLE 892, WILL YOUR COLLETS FIT?
  • WILL CELL PHONES SPARK A FIRE AT THE GAS STATION?

    I can't think of any reason that it would be dangerous. However, I checked with the Cellular Telecommunications Industry Association. The Chairman of the Association sent the following memo on 18 June 1999, to the Associations' Board of Directors and others:
    "You may have received inquiries about wireless phones causing fires or explosions at gas stations. In particular, you may have been asked about an alleged explosion at a gas station in Indonesia. We have been unable to verify any such occurrence in Indonesia or anywhere else. Moreover, in our discussions with Shell Oil they have stated they have attempted to verify these reports and also have not been able to document any such occurrence."
    Nonetheless, in an abundance of caution, some manufacturers have included language in the owner's manuals for their products that recommends wireless phone users turn off their phones while at refueling points (gas stations). In addition, we have received information that Exxon will begin issuing warning signs at all domestic gas stations advising drivers to turn off all wireless communications devices when entering Exxon gas stations.

    While wireless phone owners should always consult their owner's manual for information on the use of the phone, we are not aware of any incident that would justify these concerns."

    Gen Roessler, Editor
    HPS website

    Click the link to add information to this solution:
    WILL CELL PHONES SPARK A FIRE AT THE GAS STATION?

  • WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

    Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

    Click the link to add information to this solution:
    WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

  • DOES THE SOFTWARE WORK ON AN APPLE?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES THE SOFTWARE WORK ON AN APPLE?

  • THE SEND MAIL IN CONTACT US PAGE OF BUILDYOURCNC.COM WEBSITE DOES NOT WORK. ALSO CALLED MAILTO:

    You will need to change the default attribute of the browser that you are using (i.e. Google Chrome, IE, Firefox).

    Instructions to change this default attribute:
    1. Click on the "start menu"
    2. Click on "control panel"
    3. Click on "programs"
    4. Click on "default programs"
    5. Click on "set you default programs"
    6. Select the browser that you would like to fix
    7. Click on "choose defaults for this program"
    8. Find where it says "mailto" and set that to the default that you desire.

    Click the link to add information to this solution:
    THE SEND MAIL IN CONTACT US PAGE OF BUILDYOURCNC.COM WEBSITE DOES NOT WORK. ALSO CALLED MAILTO:

  • DOES THE SOFTWARE WORK ON A MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES THE SOFTWARE WORK ON A MAC?

  • WHY SHOULD I REGISTER MY WORK IF COPYRIGHT PROTECTION AUTOMATIC?

    Registration is recommended for a number of reasons. Many choose to register their works because they wish to have the facts of their copyright on the public record and have a certificate of registration. Registered works may be eligible for statutory damages and attorney's fees in successful litigation. Finally, if registration occurs within 5 years of publication, it is considered prima facie evidence in a court of law.

    Click the link to add information to this solution:
    WHY SHOULD I REGISTER MY WORK IF COPYRIGHT PROTECTION AUTOMATIC?

  • When will the 2000 mm HIWIN Spec Linear Guide rail be available?

    That is difficult to tell at this time. Right when we get them in, they go fast. These items come from China and the units are shipped in via freight on ship, so there are many factors on the delivery such as weather.

    Click the link to add information to this solution:
    When will the 2000 mm HIWIN Spec Linear Guide rail be available?

  • DOES MACH3 WORK ON A MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES MACH3 WORK ON A MAC?

  • WHEN WILL MY GRAPES GROW?

    It usually takes about three years before you get a viable crop from young grapevines. We planted grapevines at a house we built in California and the first crop that actually had enough grapes that we could actually pick and eat them was three years later. We ate them as we left town on our way to the East coast and our new home. They were growing strong when we passed by the old house some 10 years later.

    A few varieties of grapes produce in two years, such as Brianna and Seyval grapes.

    The good news is that grape vines usually live between 50 to 70 years, depending on the variety.

    Click the link to add information to this solution:
    WHEN WILL MY GRAPES GROW?

  • HOW DO CNC MACHINES WORK?

    A CNC machine takes codes from a computer and converts the code using software into electrical signals. The signals from the computer are then used to control motors. Since the motors can turn very small amounts the machine is able to move in highly precise movements over and over again.

    Additional Information:

    Click the link to add information to this solution:
    HOW DO CNC MACHINES WORK?

  • WHEN MY WORK PROTECTED?

    Your work is under copyright protection the moment it is created and fixed in a tangible form that it is perceptible either directly or with the aid of a machine or device.

    Click the link to add information to this solution:
    WHEN MY WORK PROTECTED?

  • I'M CURIOUS IF THESE SYSTEMS WILL ENGRAVE LETTERING ACCURATELY WITHOUT BACKLASH?

    The machines have minimal to no backlash depending on how you apply the machine. Since the cnc machines use roller chain on the x and y axes, and the roller chain is tensioned, the backlash is nearly eliminated. I say nearly because the if you control the machine in a way that there will be excessive load on the end mill, then the machine could have a tendency to spring to one side or the other because of the length of tensioned roller chain. The movement is minor and can be eliminated with the proper control of the machine.

    Click the link to add information to this solution:
    I'M CURIOUS IF THESE SYSTEMS WILL ENGRAVE LETTERING ACCURATELY WITHOUT BACKLASH?

  • IN WHICH ORGANELLE OF A LIVING CELL DNA FOUND?

    Nucleus is the organelle of a living cell DNA is found.

    Additional Information:


    Additional Information:
    nucleus


    Additional Information:
    qwertyuio

    Click the link to add information to this solution:
    IN WHICH ORGANELLE OF A LIVING CELL DNA FOUND?

  • HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

  • WHAT SETTINGS DO I USE IN MACH3 MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    WHAT SETTINGS DO I USE IN MACH3 MOTOR TUNING?

  • WHAT THE MOST POPULAR INDOOR SPORT IN U.S.A.?

    Basketball is the most popular indoor sport in the USA

    Additional Information:
    boxing

    Additional Information:
    boxing

    Additional Information:
    boxing

    Additional Information:
    Basketball


    Additional Information:
    Basketball


    Additional Information:
    Which indoor sport is the most popular in the US

    Additional Information:
    Who recorded A Boy Named Sue

    Click the link to add information to this solution:
    WHAT THE MOST POPULAR INDOOR SPORT IN U.S.A.?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.