[ Log In ]
[ Register ]

Question #: 180

Question: WHAT MY WIFE'S NAME?

Current Solution

I don't have a wife... I'm just a brain!

Respond:

Other Possible Solutions to this Question

  • what is your name?

    My name is "The Brain!!"

    Click the link to respond:
    what is your name?

  • WHAT DO I SET FOR MY STEPS PER?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    WHAT DO I SET FOR MY STEPS PER?

  • WHAT IS THE SHIPPING FEE TO MY COUNTRY?

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to respond:
    WHAT IS THE SHIPPING FEE TO MY COUNTRY?

  • WHAT IS THE SHIPPING COST TO MY COUNTRY?

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to respond:
    WHAT IS THE SHIPPING COST TO MY COUNTRY?

  • what does the error code on my vfd mean?

    Remember, steps to correct and troubleshoot issues with any electrical devices should be done by a professional electrician.

    If you have an HY series VFD, the fault codes are below:

    OC-1: Over-current during ramp up or over-current at constant speed.
    Recommended actions: 1, 2, 3, 4

    OC-1: Over-current during ramp up or over-current at constant speed.
    Recommended actions: 1, 2, 5, 6

    OC-2: Over-current at deceleration or over-current at stop.
    Recommended actions: 1, 7, 2, 9, 10

    dL: Output short circuit.
    Recommended actions: 11, 1, 10

    Ou-1 or 2: Over-voltage at stop, over-voltage at acceleration, over-voltage at constant speed or over-voltage at deceleration
    Recommended actions: 12, 13

    Fb: Fuse break.
    Recommended actions: 14, 10

    Lu: Low voltage.
    Recommended actions: 15, 16, 17

    OH: Over heat of inverter.
    Recommended actions: 18, 19, 20

    OL-1: Inverter overload 150% per minute
    Recommended actions: 2, 21, 22

    OL-2: Motor overload 150% per minute.
    Recommended actions: 21, 23, 24, 25, 26, 21

    dT: Motor over-torque
    Recommended actions: 21, 23

    E.b.S.A or E.b.S.n or E.b.S.d or E.b.S.S: No feedback from the auxiliary coil or the lectromagnetic contactor
    Recommended action: 27

    bt: Braking transistor damage.
    Recommended action: 27

    CPu: CPU fault.
    Recommended action: 27

    E.E.E.S or E.E.E.n or E.E.E.d or E.E.E.A: EEPROM fault
    Recommended action: 27


    List of recommended actions:
    If error shows at ramp up or at constant speed:
    1. Check for a short circuit or partial short circuit and the insulation of the output wire is sufficient.
    2. Increase the capacity or the inverter if it is too small. Replace with an inverter that has a larger capacity
    3. Extend the ramp-up time
    4. Decrease the torque and increase the set value.
    5. Check if the motor is blocked and if there is a sudden change in load.
    6. Check if there is a sudden chance in the power supply voltage.
    7. Extend ramp down time
    9. DC breaking is too high. Decrease DC breaking
    10. Replace the inverter.
    11. Check to see if there is a short circuit with the connection wire of the motor.
    12. Extend the ramp-down time or add a breaking resistor.
    13. Check the mains supply voltage and insure there isn't ant sudden change in voltage.
    14. Send the inverter for repair.
    15. Check whether the input voltage is normal
    16. check whether there is a sudden change in load.
    17. Check whether there is any phase missing.
    18. Check the fan in the inverter. Is it spinning? Is it blocked? Does it have any foreign matter stuck on the fins of the fan? If so, clear the fan.
    19. Check the ambient temperature in the space that the inverter is placed.
    20. Check for adequate ventilation for the inverter where it is placed.
    21. Check for jamming or any sudden change with respect to mechanical load.
    22. Set the V/F curve correctly.
    23. The motor is too small.
    24. The motor is hot and the insulation of the motor degraded.
    25. Check if the voltage has a large variance.
    26. Check if there is a phase missing.
    27. Contact the supplier

    Additional Information:
    I have cnc wood carving machine 1325 the inverter showing error 0006

    Additional Information:
    What is uc3 error

    Additional Information:
    My inverter read error oc-1 high frequency how you can help me please


    Additional Information:
    My inverter read error oc-1 high frequency how you can help me please


    Additional Information:
    203

    Additional Information:
    E2 error

    Additional Information:
    Hello , I have an Redsail cnc and I get the following error " UC3 "after that the spindle stops arter a small knocking sound ,would there be an solution to this ?

    Additional Information:


    Additional Information:
    what does it mean when my spindle VFD shows E o and stops.


    Additional Information:
    Vfd er.01.5c

    Additional Information:
    CPFO error displayed reason

    Additional Information:
    Solve it

    Additional Information:
    My Spindle VFD Holip HLPA01D523C get error E.OC.A after factory reset. and now get error E.OC.n after i change the starting mode from Start from Starting
    Frequency to Frequency track start. whats wrong with the vactory setting?

    Additional Information:
    Er20

    Additional Information:
    Fault 503

    Additional Information:
    Fault 503

    Additional Information:
    What VFD do you have?

    Click the link to respond:
    what does the error code on my vfd mean?

  • My inverter has an er.04. What do I do?

    The Er.04 (if you are using the YL VFD), generally refers to the ramping up and ramping down of the spindle, but it can be a result of a short circuit between the VFD and the spindle. You can increase the time the spindle accelerates (ramps up to the set rpm/frequency).

    Click the link to respond:
    My inverter has an er.04. What do I do?

  • What is the best way to calibrate my machine?

    In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

    Click the link to respond:
    What is the best way to calibrate my machine?

  • what causes one of my x-axis motors to overheat.

    What can cause a stepper motor to overheat can be related to a few things. First, it good to know that stepper motors will normally be hot to the touch and you should not worry about this. There is a ton of current running through the coils of a stepper motor, and current will cause heat to build up.

    Energy comes in many basic forms: movement, heat and light. Stepper motors don't produce light, so we can rule that out, so you have movement and heat. When the stepper motor is not moving, the current is still trying to make sure the stepper motor is holding its position and since movement is not a factor here, heat will build up.

    If the heat worries you, you can keep the cnc machine moving, or turned off. There will still be heat when moving, but not all of the current is being used as heat. You can also consider lowering the allowable current draw using the stepper motor driver's dip switches.

    Click the link to respond:
    what causes one of my x-axis motors to overheat.

  • WHAT IS FOCAL LENGTH

    The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

    The mirrors are 25mm wide mirrors.

    Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

    Click the link to respond:
    WHAT IS FOCAL LENGTH

  • WHAT IS CNC MACHINE?

    A CNC machine is basically a computer controlled high precision tool that is able to make intricate movements accurately and repeatedly. Our machines use common routers and spindles to mill, cut, engrave and shape materials in automated machining operations.

    Click the link to respond:
    WHAT IS CNC MACHINE?

  • What city are you in?

    We are currently located in Houston Texas.

    Click the link to respond:
    What city are you in?

  • What version of mach3

    We supply the latest stable version of Mach3. If you want control software that is a later version than Mach3, then you will need to investigate Mach4 for your CNC Machine application.

    Click the link to respond:
    What version of mach3

  • What is a #8 screw?

    A #8 nut is a nut that is used as a pair with a #8 screw to mechanically fasten parts together that contain holes just larger than the #8 screw size.

    The #1 to #12 designations are not the easiest to understand as they don't specifically inform of their size. The thread diameter of the #8 screw is .16" (the major diameter measured from the crest of the thread, not the diameter measured from the root of the thread). The minor diameter measured from the root of the thread would most closely match the inside diameter of the nut.

    Additional Information:

    Click the link to respond:
    What is a #8 screw?

  • What is return policy

    You can return any product within 30 days. There is a 10% restocking fee associated with this return.

    The return policy is stated on the terms of use for the website: https://www.buildyourcnc.com/terms.aspx

    Click the link to respond:
    What is return policy

  • what program do I use to install ubuntu on my computer?

    Here is the direct link to download ubuntu (http://www.ubuntu.com/download/desktop), now installing it to your HDD you will need to install it to a USB or burn it to a DVD. Here is a following guide to install ubuntu (http://www.ubuntu.com/download/desktop/try-ubuntu-before-you-install).

    Additional Information:
    Ubuntu comes with a program that will replace the controller software (ex Mach 3/Planet CNC), called LinuxCNC, here is the main website (http://www.linuxcnc.org/) and the main download page(http://www.linuxcnc.org/index.php/english/download).

    Click the link to respond:
    what program do I use to install ubuntu on my computer?

  • WHAT IS "BACKLASH"

    Backlash is a term used to describe the looseness in a mechanical system. Backlash can occur anywhere in a machine, but is generally emphasized at the nut and lead screw connection. If the nut threading doesn't perfectly match the lead screw thread, there will be a wiggle, or play between both the screw and nut. This is backlash. Backlash can also be located in the motor bearings, coupling (connecting a shaft or lead screw to the motor shaft), collars not being hard against the bearing, or temperature change that causes various materials to expand or contract, making the connections loosened.

    Click the link to respond:
    WHAT IS "BACKLASH"

  • What is backlash?

    Backlash is a term used to describe the looseness in a mechanical system. Backlash can occur anywhere in a machine, but is generally emphasized at the nut and lead screw connection. If the nut threading doesn't perfectly match the lead screw thread, there will be a wiggle, or play between both the screw and nut. This is backlash. Backlash can also be located in the motor bearings, coupling (connecting a shaft or lead screw to the motor shaft), collars not being hard against the bearing, or temperature change that causes various materials to expand or contract, making the connections loosened.

    Click the link to respond:
    What is backlash?

  • WHAT THE BRAIN MADE OF?

    Grey matter and a few integrated circuits!

    Click the link to respond:
    WHAT THE BRAIN MADE OF?

  • WHAT THE BRAIN MADE OF?

    It depends on what you mean be intellegent! The brain learns!

    Click the link to respond:
    WHAT THE BRAIN MADE OF?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.