[ Log In ]
[ Register ]

Question #: 2217

Question: mach 3 software compatible with 3 axis motion control combo's

Current Solution

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Respond:

Other Possible Solutions to this Question

  • IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

    Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
    Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

    The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

    If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

    Additional Information:


    Additional Information:
    Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

    Click the link to add information to this solution:
    IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

  • Is the Mach3 software compatible with 3 axis motion control combo kits? The planet cnc software is mentioned as being compatible.

    Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
    Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

    The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

    If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

    Additional Information:


    Additional Information:
    Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

    Click the link to add information to this solution:
    Is the Mach3 software compatible with 3 axis motion control combo kits? The planet cnc software is mentioned as being compatible.

  • DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

  • Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

    These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

    Click the link to add information to this solution:
    Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

  • YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

  • i purchased a breakout board from you guy and the rnr motion control is messing with my license in mach 3 tech support at mach said it is the rnr software i need help to contact them and let them see what they can do to help

    The RNRMotion driver will not conflict with the mach3 license. Make sure you have the RNRmotion driver in the plugins folder and the provided xml in the main mach3 folder. Also, make sure to have the mach3 license file in the mach3 folder. If you still experience problems, please give us a call.

    Click the link to add information to this solution:
    i purchased a breakout board from you guy and the rnr motion control is messing with my license in mach 3 tech support at mach said it is the rnr software i need help to contact them and let them see what they can do to help

  • I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

    No, you do not need another motion controller if you have the parallel breakout board and you are using the "Legacy Parallel Port Plug-In" with Mach4. The motion controller is the parallel port.

    Click the link to add information to this solution:
    I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

  • Will your basic 3 axis cnc component kit be compatible to run a regular bosch mini router?

    The Bosch mini router is a very capable router and can be used with our electronics, and machines.

    Click the link to add information to this solution:
    Will your basic 3 axis cnc component kit be compatible to run a regular bosch mini router?

  • Does your Planet CNC Software have a Digitizing Wizard like Mach 3?

    Planet CNC is currently based in the UK as a independent company, and has a G-code wizard similar to the digitizing wizard in Mach 3. Although different software, you may download a demo here (http://www.planet-cnc.com/index.php?page=download) (first link).

    Click the link to add information to this solution:
    Does your Planet CNC Software have a Digitizing Wizard like Mach 3?

  • Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

    You can find instructions for the Mach3 USB here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

    Click the link to add information to this solution:
    Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

  • I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

    Our electronics kits with the parallel breakout board will work with Mach 4, however you will need to purchase the Legacy Driver for Mach 4 to work with our breakout board.

    Click the link to add information to this solution:
    I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

    Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

    If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

    For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

    Click the link to add information to this solution:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • if buy a 3 axis cnc combo, which software would I need for working this combo?

    if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

    The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.

    Click the link to add information to this solution:
    if buy a 3 axis cnc combo, which software would I need for working this combo?

  • im converting a seig x2 mini mill to cnc and I'm looking at the 4 axis cnc combo kit is it mach3 compatible? and is everything included in the kit to build a cnc control box like wires,connectors,wiring diagrams ect?

    Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
    Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

    The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

    If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

    Additional Information:


    Additional Information:
    Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

    Click the link to add information to this solution:
    im converting a seig x2 mini mill to cnc and I'm looking at the 4 axis cnc combo kit is it mach3 compatible? and is everything included in the kit to build a cnc control box like wires,connectors,wiring diagrams ect?

  • does the planet cnc software come with the usb board on the 3: disc?

    Can you clarify what 3: disc? Thanks.

    Click the link to add information to this solution:
    does the planet cnc software come with the usb board on the 3: disc?

  • Is there any other software that will work with your controller Mach3?

    The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

    Click the link to add information to this solution:
    Is there any other software that will work with your controller Mach3?

  • CAN THERE BE CLOSED LOOP CONTROL WITH STEPPING MOTORS?

    I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

    If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

    Click the link to add information to this solution:
    CAN THERE BE CLOSED LOOP CONTROL WITH STEPPING MOTORS?

  • Are you using Mach 3 or 4? Do you ever use the etherenet outlet to control drivers?

    We still use Mach3 with a parallel port. We are looking into newer boards with USB/ethernet communication.

    Click the link to add information to this solution:
    Are you using Mach 3 or 4? Do you ever use the etherenet outlet to control drivers?

  • DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

    Yes and properly soldered.

    Additional Information:
    20

    Click the link to add information to this solution:
    DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.