[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 2304

Question: what program do I use to install ubuntu on my computer?

Current Solution

Here is the direct link to download ubuntu (http://www.ubuntu.com/download/desktop), now installing it to your HDD you will need to install it to a USB or burn it to a DVD. Here is a following guide to install ubuntu (http://www.ubuntu.com/download/desktop/try-ubuntu-before-you-install).

Additional Information:
Ubuntu comes with a program that will replace the controller software (ex Mach 3/Planet CNC), called LinuxCNC, here is the main website (http://www.linuxcnc.org/) and the main download page(http://www.linuxcnc.org/index.php/english/download).

Respond:

Other Possible Solutions to this Question

  • what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

    The redLeaf system features an integrated CNC computer preinstalled with Windows and mach3. You should only need to connect a monitor/keyboard/mouse for functionality.

    Click the link to respond:
    what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

  • What kind of computer comes with the blacktooth and do i need to install windows after purchase?

    For the integrated computer for the blackTooth, the hard drive doe not need to be formatted, but will require an OS (operating system) to be installed. Ubuntu Linux can be installed with the CNC integrated software from Linuxcnc.org. Windows can also be installed.

    Click the link to respond:
    What kind of computer comes with the blacktooth and do i need to install windows after purchase?

  • WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Click the link to respond:
    WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

  • What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Click the link to respond:
    What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

  • I DON'T HAVE A PARALLEL PORT ON MY COMPUTER. WHAT DO NEED?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    I DON'T HAVE A PARALLEL PORT ON MY COMPUTER. WHAT DO NEED?

  • what do you mean by integrated computer on the black tooth?

    The blackTooth comes in 2 combinations, 1st being with only the structure and electronic components, hardware. Without any computer parts(provided by customer)
    2nd will be structure and electronic components/hardware and computer parts(motherboard, PSU, etc.) So only input device must be provided(keyboard,mouse,screen).

    Additional Information:

    Click the link to respond:
    what do you mean by integrated computer on the black tooth?

  • DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

    That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

    Let me know and I can send a paypal invoice for the redLeaf without motors.

    Click the link to respond:
    DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. WHAT DO I NEED?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. WHAT DO I NEED?

  • How do I determine what CAM program I should use?

    There are several specifications related to CAM software that you will need to consider.

    1. The CAM software will need to be able to offer the features that match that of the machine you select to perform the fabrication. Some of these machines include, standard 3 axis vertical CNC milling machine, turning machine, and 4 or 5 axis CNC machine.

    2. The CAM software will need to contain the features that you feel are necessary for how you will apply the machine. For example, are you making signs? Are you milling parts for a machine? There is a wide array of CAM software that will work well for one application and not another.

    3. The CAM software will need to work well with your workflow and processes, and have the user interface that you prefer.

    Click the link to respond:
    How do I determine what CAM program I should use?

  • What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

    The breakout board has a relay installed and uses the terminals labeled S, O and P. The following link explains the operation of this relay and how to connect the terminals:
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/8/

    You will run your power cord (use an extension cord rather than the actual power cord of the router) through the relay using the S, O and P. The P is a general connection and the S is normally closed (S and P is connected when the relay is not engaged) and O is normally open (O and p are not connected until the relay is engaged).

    There are three wires in the power cord: neutral (white), live (black) and earth ground (green). You will run your neutral wire (white wire) through this terminal. At some point in the power cord, remove the outer insulator and expose the three wires within. Cut your neutral wire and strip both ends of the cut. Then insert one end in P and the other end in O (normally open), so Mach3 or other control software you are using will engage the relay and the router will turn on.

    You will need to setup your control software to turn on the relay using Pin #16 as this is the digital signal pin that controls the relay.

    Click the link to respond:
    What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

  • My blackfoot 4x8 Starts sending erratic commands to the machine randomly in the middle of a program or freezes altogether. Replaced USB Cable, updated software, updated firmware, tried other computers. What else should I do?

    If the computer has been tested to be functional, it is most likely the breakout board which is faulty. Replace the breakout board and it should solve these issues.

    Click the link to respond:
    My blackfoot 4x8 Starts sending erratic commands to the machine randomly in the middle of a program or freezes altogether. Replaced USB Cable, updated software, updated firmware, tried other computers. What else should I do?

  • I have one more question pertaining specifically to the integrated computer model. Do I need an OS to load onto the computer or is there one already pre installed?

    On our CNC computer systems, we provided all the hardware required for a fully functional control package. But software items are not included OS systems and Supporting Software are not include, however if windows 7 is ordered we supply the mach 3 demo.

    We do not add the OS system to our systems, due to the options that our customers have either going with(linux, windows).

    Click the link to respond:
    I have one more question pertaining specifically to the integrated computer model. Do I need an OS to load onto the computer or is there one already pre installed?

  • My computer doesn't have a parallel port connection. Can I use a usb to parallel port cable to communicate with my breakout board?

    A parallel to USB adapter will not work. You will need to use a USB interface like the ones below:

    Mach3 USB interface:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Poeys57CNC Interface:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Additional Information:
    To answer the question in more detail, the parallel port is actually an extension straight from the CPU and is also called the GPIO (General Purpose I/O) pins. These pins carry signals independently, hence the description as being a parallel port.

    The stepper motor driver receives a pulse train (series of pulses). A single pin on the parallel port sends a pulse train to one stepper motor driver and stepper motor for a single axis. Another pin on the parallel port sends a pulse train to another stepper motor driver on another axis. This happens simultaneously as with the direction signals for each axis.

    If a parallel port is adapted through a USB (using an adapter), the parallel port cannot have these signals happen in a simultaneous fashion and will cause the stepper motors of a CNC router or machine to be very clunky, if it works at all. To elaborate, the computer sends an instruction to the USB to send a high signal to pin 1, so it does, then another signal to pin 2, so it does. This is happening one after another. The speed at which this happens is reduced dramatically, and the position of one axis may now be out of sync to another axis.

    The reason the USB interfaces (linked above) work is that the USB delivers broad instructions to the interface (to a microcontroller) and the interface parses the instructions and outputs simultaneous signals to the stepper motor drivers.

    Hope this helps.

    Click the link to respond:
    My computer doesn't have a parallel port connection. Can I use a usb to parallel port cable to communicate with my breakout board?

  • So after I install the stepper motors, how does the system know what’s the start position ? I’m modifying a lathe.

    If you are using a control program, like Mach3, then you will move (jog) the axis to the location that you want to set as your start position and "zero" that axis. Make sure that the axis moves in the positive direction where you would expect. If this is not the case, you will need to reverse that axis according to the instruction with your control program.

    Click the link to respond:
    So after I install the stepper motors, how does the system know what’s the start position ? I’m modifying a lathe.

  • I believe I understand USB v Parallel BoB on the Blacktooth but what is "integrated computer" mean?

    Integrated computer for our blackFoot means, that the computer components will be included with that kit. Meaning that a motherboard(mini itx) with a on-board processor, RAM, HDD and power supply is sent.
    So the blackTooth will be a all in one kit, excluding any software with the price.

    Click the link to respond:
    I believe I understand USB v Parallel BoB on the Blacktooth but what is "integrated computer" mean?

  • I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

    The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

    Click the link to respond:
    I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

  • I need to replace the on board computer of my laser engraving machine

    What model laser cutter and engraver do you have? What is the model number of the laser controller within the laser cutter and engraver?

    Click the link to respond:
    I need to replace the on board computer of my laser engraving machine

  • The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

    Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

    How old is your CNC computer system?

    Additional Information:
    The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

    Additional Information:
    You're welcome

    Click the link to respond:
    The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

  • what operating system comes with the laser (Integrated Computer) Option

    You have multiple options to run the laser but if you want us to install a OS system,you will have to buy the windows 7 license and mach3 license to run the machine with the parallel BB/if you would get the USB BB you will need to get planet CNC, you can also go with a free system Linux and have emc run the cnc machine.

    Click the link to respond:
    what operating system comes with the laser (Integrated Computer) Option