The maximum length we can ship is a total of 78" inches. However we can send your required length in portions. Please refer to adding the total items you require to your cart to get a visualized amount and shipping cost.

Click the link to add information to this solution:
Regarding 1/2" 5 start and 10 TPI ACME precision lead screw, what the maximum length you can ship within USA? I'm looking for something like 100" and I could use a 1" screw if available. Please include estimated price. Thanks.

We don't hold those boards in-house anymore. You can use the schematic to form your own boards if you wish.

Additional Information:
Thanks for the reply. Has this proven to be a good design?

Additional Information:

Click the link to add information to this solution:
Regarding L6203/L297 Stepper Board Driver, would you be willing to sell two unpopulated boards? A friend and I are each building a low cost CNC and I already have most of the components. Thanks.

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

We sell our ACME screws in total length (overall length you require), but if individual lengths are needed you can contact us via phone (281-815-7701) or email (customerservice@buildyourcnc.com).

A $2.00 order will be a total of 1 inch, but if ordered separately then you will receive 2 of the same length.

Click the link to add information to this solution:
For the 1/2'' 5 start ACME leadscrew, what is the length purchased for the $2.00 order? and if you make 2 orders, are you getting two separate rods or 1 rod at twice the length. Thanks.

Conceptually it is straightforward to predict the radiofrequency (RF) exposure intensity at any point in the vicinity of a cellular radio base station antenna. Simply multiply the effective radiation power times the inverse square of the distance times the relative gain of the antenna in the direction of the interest. The relative gain in different directions is know as the antenna radiation pattern and is usually available from the antenna manufacturer in graphical or tabular form.

Unfortunately, in real life the calculations involved in base station antenna evaluations are quite complex and require expert knowledge and experience to deal with the many parameters that are involved. An excellent reference summarizing this process is the Federal Communications Commission OET Bulletin No. 65 titled "Evaluating Compliance With FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields," available on the Federal Communications Commission (FCC) website.

To assess the RF hazards associated with handheld cell phones it is necessary to predict the rate of absorption in the body of radiofrequency energy, a parameter called the specific absorption rate (SAR). This is a very complex calculation, and cell phone manufacturers often rely on measurements of SAR in fluid-filled cylinders or plastic containers in the shape of a head. The FCC requires cell phone manufacturers to provide this data to FCC. You can obtain the data for your model phone on the the FCC's website. Unfortunately only cell phones manufactured in the last couple years are listed here.

As to your question about keeping RF exposures within the safety code, please read the other questions posted on this website this matter. Cellular radio products that meet FCC requirements will be within the guidelines established by safety standards organizations for users' and public exposure to RF radiation fields.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
FIRST OF ALL, THANKS FOR DESIGNING A WONDERFUL SITE. MY QUESTION IS: HOW DO YOU CALCULATE EME (ELECTROMAGNETIC EMISSIONS) AROUND THE TRANSMITTER (ANTENNA) AT ANY GIVEN POINT AND WHAT ARE MEASURES TO KEEP IT UNDER SAFETY CODE?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to manage USB Controller (Breakout) from my own (custom) Windows application? Is there a driver API or smth for that?

Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.

Not a problem. The ALM is rather self-explanatory as this is a closed-loop stepper motor and driver that you are using. The ALM (alarm) is a signal that is used to tell the driver/controller that the motor is not in the same condition that the driver expects. In a closed-loop system, the motor has an encoder that tells the driver exactly how many steps that it turned, and if this value does not coincide with the driver's outputted number of steps, and within a specified amount of time, the alarm will trigger so the system can stop and the workpiece can be salvaged.

The MF is simply a signal that tells the driver that there is impending direction and step pulses coming. If the MF signal is high, then that is similar to an enable signal.

Click the link to add information to this solution:
Hello I recently read your site and have a question. I have a driver model DM2722A but I can't connect it to my usb controller due to the fact that the driver is not marked enable, but instead it is marked: mf-, mf +, alm-, alm +. I will be very grateful if you explain to me the meaning of the latter and tell me what should be related to "enable" Thanks in advance!

The formula for finding the steps per mm is found in the units itself. First, you mentioned that the motor is a servo. This needs to be clarified as a servo is different than a stepper motor. Some servos behave similar to a stepper motor, so I will continue with this in mind.

The formula is (steps/mm):

You need to find the steps. The stepper motor has a natural number of steps per a full revolution. This is typically 200 steps per revolution.

The driver for the stepper motor allows you to increase the number of steps per revolution by adding a specified number of steps between each step. For instance, if you set the driver to 1/4 microstepping, then instead of having 200 steps per revolution, you would have 200 x 4 = 800 steps per revolution.

So now we have the first part of the formula:

Steps / mm = (200 x 4) / mm

Lets determine the mm side of the formula:

You mention that the pitch is 0.5 mm. Check to insure that the lead is also 0.5 mm. This could be a multiple start lead screw where the pitch is different than the turns per mm. If in this case, that the 0.5 mm is the travel for one full revolution, then you can simply plug this into the formula as:

mm = .5 mm

Otherwise, determine how fat the travel is for one complete revolution.

Therefor, with what we know and the driver is set at 1/4 microstepping and the stepper motor has a natural step count per revolution at 200:

steps / mm = (200 steps x 4) / 0.5 mm = 800 steps / 0.5 mm = 1600 steps / mm

If your travel for one revolution is not 0.5 mm, then plug in your travel distance instead.



Additional Information:
i know about steps/mm calculation for stepper motor, because i am using servo motor that why i asked about that. please tell for servo motor.

Additional Information:
because its my first time with servo motor i have no idea about calculation of parameter with servo.

Additional Information:
Have you attempted to contact the manufacturer or seller of the servo? We typically respond to customers of our products on this customer service area, unless we have extensive knowledge of the subject and can answer the question efficiently.

Additional Information:

Click the link to add information to this solution:
hello there, i am using servo motor for my X and Y Axis but i dont know how to calculate steps/mm for that, the lead screw i am using is have pitch of .5 mm. please helpme on this i have done everything only this point is pending.

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

Roller chain in general is adjustable by using "master links", which are links which have horseshoe clip holding the pin and thus allow connections to be made or broken. The #25 is a designation of the type of roller chain. ANSI codes designate that the first digit(s) specify the pitch in eights of an inch, and the last digit is 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. So #25 is 2/8 = 1/4 inch pitch bushed chain with no rollers.

Click the link to add information to this solution:
IS THE "#25 ROLLER CHAIN" ADJUSTABLE TO ANY LENGTH? LIKE IF I ORDERED TEN FEET OF IT, CAN MAKE TWO 3-FOOT LOOPS AND ONE 4-FOOT LOOP USING SOME SORT CHAIN JOINER?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

Hey, sorry I just found the wiring diagram and see that #4 is disabled. My bad. Thanks.

Click the link to add information to this solution:
I just purchased some wire for my 2.2 spindle as per your recommendation it's 14 AWG stranded wire for the VFD to Spindle (U, V, W) connections. However, it's a three wire (black, white and Ground). Which numbers on the female pin connector do I connect the wires to. Cheers.

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

I just sent you the commercial invoice via email. Thanks.

Click the link to add information to this solution:
Could you please e-mail us the invoice for the order, shipment is currently at the customs and your invoice is needed so it can be cleared. As I can't seem to find any order number or other reference in your system, the only reference I have is the tracking number LZ676176940US and the order date is 12/26/2017. Thanks!

Hi. The HIWIN spec rail will fit standard M5 screws. If you are using non standard screws with wide heads, or pan heads that are a bit larger than a standard round heads, then it may not fit. Make sure to source screws that have standard round heads, or socket heads for fastening the 20mm HIWIN spec rails.

Click the link to add information to this solution:
I purchased some of your 20mm Hiwin Linear Rails. M5 bolts do not fit flush. The head stands out. Is the spec sheet out of date? What bolts will fit this rail AND T Nuts compatible with 8020's 15 series extrusions? Thanks.