The blackTooth laser power supply will use 4 - #8 x 1" screws, and 4 - #8 nuts. As stated on step 10 here (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/10/)

Click the link to add information to this solution:
I am building a blacktooth. I don't see in the instructions what screws are meant to fasten the power supply to the wood. The instructions show how to wire it but I don't see where it says which screws to use. I don't want to guess and end up being short later. Thanks. .

WE don't have an actual file that contains the instructions for the machines as they are a part of a larger database file that is queried during the product page's rendering in the browser. The best option would be to print the webpage on a printer and use that as notes.

I know this will not provide larger images, but you could use the paper version to write your notes while assembling the machine using the larger images on the website.

Click the link to add information to this solution:
On the blackFoot 4'x8' CNC machine do you have the instructions under one file that I can download, I want to print them out and make notes as I am building the machine.

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

Use a clamping collar (if you are using an ACME lead screw) or a couple of 1/2 nuts (if using an allthread) against the bearing to keep the bearing in place and make sure there is no axial play.

Click the link to add information to this solution:
How do I secure the non-motor end of the lead screw for my 'Book' machine build? Does it just sit inside the bearing or do i use a nut to lock it in place? I did not see any instructions for this in the book.

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

We apologize for the confusion! The current greenBull kit in the video is a 4' x 8' gB CNC machine, so we currently have a shorter Y-axis length, compared to the 5X/6X kits. However with the gB 5X you should skip every other section(or something similar so it is symmetrical), since we added the option for you to increase the number of ribs if you wish, but is not necessary for the CNC machine.

Click the link to add information to this solution:
Building the 5x10 GreenBull, I went to install the ribs on the mid section of the gantry and you say in the video to skip a spot for the motor to sit, but I have 3 sections that are going to blank not just one like you show in the video. Do I skip more than one, am I missing ribs?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

The greenBull videos are back up. The videos were blank since we added security to the website and those videos were coming from an unsecured http version of YouTube rather than their https.

Click the link to add information to this solution:
greenBull Assembly Instructions The following videos are missing: https://www.buildyourcnc.com/greenBullCNCMachineKit.aspx

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a cnc router with twin ball screws on the long axis and I will have a rotary axis as well. I need a 5 axis breaker board using only 4 axis total. Can you help me?

You will need a CNC software that will control your router cnc machine, and your design CAD/CAM software will need to know the CNC software you plan on using so the post processor in the CAM software can create the g-code for the CNC control software. So if you have for example, Mach 3 and our parallel breakout board, you can use the Mach 3 post processor in your design software.

Click the link to add information to this solution:
I'm new to CNC and just finish building my router.I need software for my post processor and not sure if your product is what I need?

This is correct if it is the Mach3 USB controller. You will also get a rapid flashing led if you jog the machine (assuming the machine is not in reset mode or e-stop mode).

Additional Information:
Is it suppose to be blue or red? Mine is red.

Additional Information:

Click the link to add information to this solution:
The instructions for installing the USB board say there should be a blue LED light up when computer is connected. I get a flashing red LED that goes solid when I start

What laser controller model number do you have?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Thanks for the model number. I am going to fabricate the parts and put it together myself to see the issue. We made this modification to the blackTooth laser cutter to better house the new laser controller that we wanted to add to the laser, but that may have been for the AWC608. If there is an issue with my assembly, we will create a new part that will correct the issue and send it to you.

Additional Information:
Thank you for the update!

Additional Information:
Have you had a chance to duplicate the issue yet?

Click the link to add information to this solution:
There are no instructions on how to assemble the laser control unit housing that came with my 40w blacktooth laser kit. How can I get instructions for how to assemble the control interface housing? Every configuration I try blocks the wire connection ports.

The settings that will have to be change will be your steps per inch in motor tuning (mach 3), or settings/axes(planetCNC). But we do not have the actual numbers/specs that will fit your 10 TPI 5 start lead screw, here is a tutorial video which explains how to get the exact numbers you need! (

Click the link to add information to this solution:
I just changed my X and Y to the ACME 1/2" 5 start lead screw. What are the motor tuning numbers. I have the book built machine.

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

You can find all of the wiring instructions for the Mach3 USB controller here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down until you see the videos. The wiring instructions cover wiring all of the axes, setting up the inputs to sense limit switches, setting up the outputs and how to diagnose the outputs, setting up an external relay to control external devices, and setting up spindle speed.

Click the link to add information to this solution:
where can I find wiring instructions for the Mach3 USB controller?

Yes, the plans are detailed sufficiently enough to produce CAD drawings. If you wish to create AutoCAD drawings from the plans that we provide, we ask that the information conform to the creative commons license established on this site.

Click the link to add information to this solution:
If i can get the autocadd drawings of the building mdf peices that need to be build are the plans detailed enough for me to make my own autocadd drawings? I have access to another machine to build my own.

Yes, you can use the onboard relays on the pokeys57CNC controller to trigger the plasma torch.

Click the link to add information to this solution:
I want to trigger a plasma torch with the Pokeys57CNC that I bought from you. I am connecting a Proma THC following your basic instructions for the Plasma sense But I don't know what I would use to trigger the torch. I watched the video on lazer engraver. Can I use the same for triggering a plasma torch?

You will definitely want to adjust your debounce setting in mach3 if your emergency or limit switch is engaging.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you try changing the denounce setting?

Additional Information:
Meant to say denounce.

Click the link to add information to this solution:
When I start my spindle I get a emergency stop in Mach 3. I have run shielded cable and it is grounded at the VFD it is wired per you site instructions. any idea what to check

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed