Since the nozzle is getting warm, much of the laser energy is not exiting the aperture and is hitting the inside of the nozzle. You need to align the laser's final mirror to direct it out of the nozzle's aperture and you will have more than enough energy to cut 1/8" acrylic efficiently.

Click the link to add information to this solution:
I've been unable to cut through acrylic or wood at a thickness of 1/8" or less with the BlackTooth. Even with multiple passes (x10) and full power, a clean cut cannot be accomplished. Based on videos I've seen something doesn't seem right. I noticed that the nozzle gets very warm, almost untouchable during even short runs.

There are several endmills that would work for that application. Here's the one we use in our own shop: https://buildyourcnc.com/Item/endmill-singleflute-upcut-Onsrud-1-flute-plastic-wood-aluminum for cutting .75 inch MDO.

Click the link to add information to this solution:
Which end mill would you advise to buy for cutting in full depth MDF and plywood of up to 20mm thickness? I am about to install a 2.2k spindel on my cnc.

Yes, you can preset an origin by zeroing the machine at the desired location before beginning your work. You can return to that exact point at any time, or you can specify an offset from that point to be the beginning point for the next machine operation (for instance when cutting several parts from one sheet of wood.) Jogging time varies by machine and application but would generally be a rapid move -- our default rapid setting is 400 inches per minute.

Click the link to add information to this solution:
Can you preset an origin point on this cnc? How long does it take to jog over? (If I have the case that I using the same thickness of maple wood, and same jig everytime)?

Yes, the blackTooth actually has a base that is open, so you can set the blackTooth laser cutter on a surface that is depressed as much as you need so you can accommodate a work piece with very large heights.

Click the link to add information to this solution:
I'm considering the purchase of your Blacktooth laser. I will be engraving on my wood blocks that are two inches in thickness. Will the Blacktooth accomodate this thickness material?

You should apply a spoilboard to the top surface of the machine. The bed of the machine is not intended to be used as a spoilboard.

Click the link to add information to this solution:
3. The bluechick spoil board appears to be a structural member of the machine, how easy is it to replace. To start, I would assume that would be cheaper than buying your spoil board planner.

Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.

with parallel port controllers, you have the ability to jog using two axes at the same time, but with USB controllers, this is not possible.

Click the link to add information to this solution:
[575] Hi, I recently purchased this board and everything seems to be fine! But I am not being able to jog two axis at same time as I used to do on my older board. Did I do something wrong?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
I was wondering if it is at possible to get a autocadd drawing of the pieces that need to be built for your cnc hardware kit

We attempt to provide as many services as possible to fit the needs of the CNC community. For a quote on a custom job, please email customerservice@buildyourcnc.com and we will be happy to assist you.

Click the link to add information to this solution:
I bought longs motor nema 34 stepper motor with 4 powers supply and dm860 from ebay, would you be interested in doing all the wiring for me? I pay you for you time

The KL-4030 is a Keling 3.0 amp stepper motor driver. These are generally pretty robust drivers. You mentioned in the question that it worked for one hour. This sounds like it could be a contact issue with the wiring in the terminals. I would recommend that you check all of the connections. The terminals that are used in these drivers have terminals that are easily used incorrectly.

Make sure to open the terminal all the way using a small screw driver. Then insert the exposed wire into the opening and re-tighten the terminal. Make sure of a good connection by tugging on the wires.

Also, check kthe digital wires that connect from the driver to the control board.

Click the link to add information to this solution:
I have a KL-4030 stepper motor driver that I only have about an hour use on it but seems to be bad already. Has anyone out there had the same problem?

This was true for controllers that use the parallel port to communicate with the CNC as the CPU is sending signals to each of the parallel port pins (GPIO or General Purpose Input/Output). With newer types of controllers that use the USB connection, this is not a problem anymore since all of the signal processing happens on the controller rather than in the computer. The computer only needs to send high-level commands to the controller and the controller translates the simple commands to pulse trains that the drivers can accept.

Additional Information:
I don't believe that the board itself buffers. MAch3 however, does use an algorithm for look-ahead.

Additional Information:
Thank you for the information. I plan to use a second SSD with a minimal Windows 10 or 11 system.

Click the link to add information to this solution:
[575] Buffering. In former days, I used a MS DOS application to do the milling jobs. I was told that Windows sometimes does other jobs ans so my milling job would be ruined. Does this USB board buffer some of the CNC data to circumvent such errors?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Considering that "materials being lased by may emit gasses that are harmful to humans (corrode human tissue and cause damage to respiratory organs). Always read the MSDS (Material Safety Data Sheet) for the material to be lased. You can find these MSDS from manufacturer websites for the material you are considering for use in the laser system."
We successfully have worked on Thin sheets of Brasswood, glass, foam, plexi-glass. The thickest materials you will be able to successfully cut is 1/4".

Click the link to add information to this solution:
I am looking at buying the blacktooth-laser-cutter-engraver-40w. Can you give me some idea of the types and thickness of material this machine will cut and/or ingrave?

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I live in Australia and am looking at purchasing the Blacktooth laser cutter and engraver. I am wondering what the cost to ship to Australia would be?

The greenLean machine comes with the entire structure and features a 4'x8' cutting area. You will still need some hookup wire to connect the electronics and silicone tubing for the water to and from the spindle.

greenLean Machine: https://buildyourcnc.com/item/cnc-machine-greenLean-v1

Thanks for answering my last question. So I have two follow-up questions from the response. The green leaf stands vertical is it designed for the material to be cut without falling free once it is cut through? And second question: you metioned water running to the spindle is this a cooling system for the spindle?

You would use holding tabs to keep the parts from falling out of the cut areas. Holding tabs are generated as part of the CAM file. Yes, this is the way the spindle is cooled. This is far superior to air cooling. Air cooling will blow the chips all over the shop.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am loking for a kit that can cut 4x8 material and would be ready to cut when assembled. plus what computer and software are needed to be ready to cut?

Cutting metal with lasers even at 100W and 130W is difficult. The main problem is molten is a byproduct of lasing, which can severely damage the laser.

Click the link to add information to this solution:
For the XL Vertical Laser Machine I see it won't cut metal as it is only 80w. However, I noticed that you are working on 100w and 130w versions so will that be sufficient to cut through sheet metal? If so, how much longer until those are available?

A CO2 laser will not be suitable for cutting steel. You would likely need a very powerful fiber laser to cut steel, and even then you have to take into consideration the reflective properties of steel which can pose danger to the machine.

Click the link to add information to this solution:
Trying to cut 24, and 26 G steel sheets in various shapes. Will CO2 laser be enough? And will it cause alot of heat in the product?