This is a good video on how to do a vacuum table

Click the link to add information to this solution:
Do you have any videos or plans for how to make a strong table for a large CNC router? I saw the torsion box videos but would like some more guidance on how to build just a good table.

WE don't have an actual file that contains the instructions for the machines as they are a part of a larger database file that is queried during the product page's rendering in the browser. The best option would be to print the webpage on a printer and use that as notes.

I know this will not provide larger images, but you could use the paper version to write your notes while assembling the machine using the larger images on the website.

Click the link to add information to this solution:
On the blackFoot 4'x8' CNC machine do you have the instructions under one file that I can download, I want to print them out and make notes as I am building the machine.

(These steps are to be taken with precaution, due to the fact that we do not know the model or manufacturers specifications for your BoB)

Here is a link to our CNC electronic videos(

Click the link to add information to this solution:
I have a CNC Machine from China, and the Breakout Board is not Labeled. Is there any way to test the board using Mach3 to find out the pin designations? db25 bob

To convert the whiteAnt to a CNC machine, you will want to lower the upper structure to the lowest position to create the most rigidity overall. You will see that there are many holes below the sides of the upper structure that are evenly spaced. This is so you can adjust this lower. You will also want to fasten the lower sides to a substrate (piece of wood, or something) with l-brackets or something that has a bit of adjustment capability. This will keep the sides more rigid as well. Use a Dremel for the spindle. If you want to use a another spindle, let me know and we can product a mount for that spindle since the Dremel has poor runout (TIR). This is important if you are wanting really precise milling.

Click the link to add information to this solution:
how can I convert the whiteAnt from the 3D printer mode to the CNC milling mode?

You can find a diagram that describes the pin-out for the 2.5 am Driver that is intended for the 3D Printer Main Board, but can be used as a standalone driver as well.

Additional Information:
Where is the diagram located?

Click the link to add information to this solution:
Is there a diagram or schematic showing which pin on the 3D printer driver is ABCD?

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

We don't have a laser kit to retrofit another CNC router other than ours, but we can create one. Some things that may help:

- You are located close to use so we can work closely with you to implement to retrofit,
- or you can provide very detailed drawings or measurements so we can use them to create the necessary parts for the kit.

Other things that you need to understand:

- A laser has a number of parts that will bulk up the head of the CNC router causing a bit more inertia which may require lowering the acceleration for smooth ramping up and down of the velocity

- The bulk of the parts required for the laser may restrict the travel of the x and/or y axes.

- The nozzle of the laser will be offset from the end mill of the spindle.

Can you tell me the brand of the CNC router that you would like to stick a laser on? (you can answer by submitting additional information.

Click the link to add information to this solution:
Do you have a laser kit that can be fitted onto another brand CNC router?

Yes, that is highly recommended for all the reasons you can imagine. Say you were doing engraving, not surfacing the spoilboard will either exhibit some areas that have no engraving at all, or areas that have engraving that is too deep. If you are cutting completely through the material, then one end may be cut all the way through but the other end will not have a complete cut, or produce onion skinning on the bottom of the workpiece.

Click the link to add information to this solution:
DO NEED TO GET THE BIG PLANING BIT OR SURFACING AND GO OVER SPOIL BOARD MAKE SURE THAT IT IS PERFECTLY LEVEL IN RELATION ROUTER?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

You can modify our machines to have a camera to view your process and pick up registrations.
Here you can see a one of our customers adding a webcam to his machine! (https://www.buildyourcnc.com/tutorials/Example-customer-blacktoe-clintW)

Click the link to add information to this solution:
Would your CNC machines be able to have an optic camera to pick up registrations marks from a printer?

The instructions for assembly are found in the book. If you are interested in purchasing the plans and instructional DVD please see this link https://buildyourcnc.com/cnckitintro.aspx

Click the link to add information to this solution:
I read the book and i want the vedios show assembly the CNC Machines please give me alink for vedios

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

Ok, sure. Let's get the discussion started. Please respond with your questions on this FAQ

Click the link to add information to this solution:
Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

Portable cell phones emit about 0.6 watts of radiofrequency energy, limited primarily by the power of the battery. As with any radiofrequency transmitter, there will be some amount of absorption in the human body; the amount depends on how close you are to the antenna. The Federal Communications Commission (FCC) limits the amount of radiofrequency energy which cell phones can deposit in the body to levels at which no health effects are to be expected. See an article on Cell Phone Safety on this website for more information.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
HOW MUCH RADIATION GIVEN OFF BY A CELL PHONE AND THERE ANY WAY TO STOP THE FROM BEING ABSORBED INTO YOURSELF?

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

If you remove the dust shoe, you should be able to reach the collet to remove the end mill.

Click the link to add information to this solution:
DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?