[ Log In ]
[ Register ]

Question #: 6890

Question: I purchased a vfd and spindle from a friend, his set up is 220. I don't have 220 in my shop. My question is can I use your 110 vfd with this spindle??

Current Solution

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Respond:

Other Possible Solutions to this Question

  • I purchased a vfd and spindle from a friend, his set up is 220. I don't have 220 in my shop. My question is can I use your 110 vfd with this spindle??

    Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

    Response
    The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

    Was originally on a Delta C200 vfd. That is 220 single phase.

    Click the link to add information to this solution:
    I purchased a vfd and spindle from a friend, his set up is 220. I don't have 220 in my shop. My question is can I use your 110 vfd with this spindle??

  • HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

    Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

    VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

    Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

    UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

    Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

    Click the link to add information to this solution:
    HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

  • Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

    Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

    VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

    Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

    UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

    Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

    Click the link to add information to this solution:
    Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

  • I have wired up my 110v VFD and my 2.2Kw spindle and I get an E.Lu.5 code. My wiring is correct and the parameters are set to those for the VFD according to your website I found in a previously answered question from someone here. Any help would be greatly appreciated, thank you!!

    The E.Lu.5 Error code on your VFD is related to Low Voltage.

    The recommended action is:
    - 1. Check whether the input voltage is normal. (the voltage from the wall/breaker to the VFD)
    - 2. Check whether there is a sudden change in load.
    - 3. Check whether there is any phase missing.

    Unfortunately, these three recommended actions will probable require an electrician to test the line going into the VFD.

    Additional Information:

    Click the link to add information to this solution:
    I have wired up my 110v VFD and my 2.2Kw spindle and I get an E.Lu.5 code. My wiring is correct and the parameters are set to those for the VFD according to your website I found in a previously answered question from someone here. Any help would be greatly appreciated, thank you!!

  • I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

    Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

    VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

    Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

    UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

    Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

    Click the link to add information to this solution:
    I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

  • Hello, I have a chinese 2.2KW spindle that is nearly new purchased with a CNC I bought while in china, I have noticed at lower RPM there is a distinct squeal. Does this indicate bad bearings?

    The squeal you hear from your spindle running at low RPM is probably not associated with bad bearings (I guess it depends on the sound). All of our spindles running at low RPM has a distinct sound, probably caused by the coils and the magnets.

    Click the link to add information to this solution:
    Hello, I have a chinese 2.2KW spindle that is nearly new purchased with a CNC I bought while in china, I have noticed at lower RPM there is a distinct squeal. Does this indicate bad bearings?

  • I purchased a 4ft X 8ft Blackfoot CNC machine in 2015 and to this date have not been able to use it. How can I get some help. Thank u
  • I purchased the spindle cooling kit with power supply. and was wondering if you have a diagram on installing or a video. thank you

    The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

    If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

    Click the link to add information to this solution:
    I purchased the spindle cooling kit with power supply. and was wondering if you have a diagram on installing or a video. thank you

  • I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

    That is a very loaded question that could be replied in so many ways. I will need a more specific question to help you. For instance, I have my machine moving in different directions, but I don't know how to make the machine move according to g-code instructions. Another question could be, I connected all of my electronics and the motors are not moving and I did all of the steps on the electronics video to troubleshoot the problem.

    Click the link to add information to this solution:
    I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

  • I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

    You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

    I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

    Pokeys57CNC product page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Mach3 USB product page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to add information to this solution:
    I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

  • I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

    Can you provide the model number of your VFD?

    Yes, I have the "YL600 - 2S - 2K20"

    It just came with a small booklet that is all in Chinese...

    Click the link to add information to this solution:
    I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

  • I just purchased the 2.2 kW water cooled spindle. I also ordered a 1/8" collet to go with it, since I assume it comes with a 1/4" collet. Is this correct?

    Spindle comes with 1/4" collet.

    "All of our spindles come standard with a 1/4" collet. The 2.2kw, and 4.0kw, can be upgraded to a 1/2" collet with a separate purchase"

    Click the link to add information to this solution:
    I just purchased the 2.2 kW water cooled spindle. I also ordered a 1/8" collet to go with it, since I assume it comes with a 1/4" collet. Is this correct?

  • It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

    Is this CNC related. If so, what controller are you using?

    Additional Information:
    I'm using the Mach 3/USB CNC interface board, with the Mach 3 software.

    Additional Information:
    Does the LED on the controller light up, or blink?

    Additional Information:
    I believe I've corrected the issue. I found that their are 2 spring like tabs on the female USB port. And take a sharp point like on a compass and gentle raise those tabs a bit. This tighten up the connection, and I never received an error from losing connection.

    Click the link to add information to this solution:
    It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

  • Will your 2.5 KW spindle work with my Hitachi WJ200-022SF VFD and does it have a thermal couple temp output?

    From reading on the Hitachi WJ200-022SF VFD, it seems as it will work just fine with this VFD. However since we have not tried this cross match, I would carefully take each connection and setting into great consideration and detail on both the Hitachi recommendations for setup, as well as our spindles recommended setup.
    Our spindles do not have a thermal couple temperature output.

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Will your 2.5 KW spindle work with my Hitachi WJ200-022SF VFD and does it have a thermal couple temp output?

  • [77] I have a 110 volt 2.2kw water cooled spindle. Can I run it with a 220 volt VFD?

    I have not tried connecting a 110V spindle to a 220V VFD; however, the parameters in a 220V VFD do allow changes to the values for the spindle motor. If you do plan on connecting the 110V spindle to a 220V VFD, damages can occur, so I would not recommend it.

    With that said, here is the output of an LLM:
    Using a 220-volt VFD (Variable Frequency Drive) to run a 110-volt spindle is technically possible, but it requires careful setup to avoid damaging the spindle. Here's what you need to consider:

    Check the VFD Specifications: Ensure that the VFD can be set up to output the correct voltage for your spindle. Many VFDs are capable of outputting variable voltages and can be configured via their programming settings to match the voltage requirements of the spindle.

    Adjust the Output Voltage: You'll need to configure the VFD to output 110 volts to match your spindle. This is crucial because supplying 220 volts to a 110-volt spindle would likely damage it permanently. Check the VFD's manual for instructions on how to adjust the output voltage settings.

    Set the Current Correctly: Besides voltage, make sure the output current does not exceed what your spindle can handle. The VFD should be configured to supply the current at the rating appropriate for the spindle’s power and voltage requirements.

    Consult the Manuals: Always refer to the manuals of both the spindle and the VFD. These documents can provide specific guidance on compatibility and settings.

    Consider Professional Installation: If you are not familiar with electrical systems or if the manuals do not provide clear guidance, it may be wise to hire a professional. This helps ensure that the setup is done safely and correctly.

    By taking these steps, you can safely use a 220-volt VFD with your 110-volt spindle, ensuring it operates efficiently without risk of damage. Just be meticulous with the settings and when in doubt, consult with or hire a professional.

    Click the link to add information to this solution:
    [77] I have a 110 volt 2.2kw water cooled spindle. Can I run it with a 220 volt VFD?

  • Could I safely use a 2200w 220 to 110 converter and uninteruptable power supply with my 2.2kw inverter and spindle?

    Yes, you can use a 220 to 110 step down transformer to provide power to your 2.2kw VFD and spindle.

    Click the link to add information to this solution:
    Could I safely use a 2200w 220 to 110 converter and uninteruptable power supply with my 2.2kw inverter and spindle?

  • I PURCHASED YOUR BOOK TO BUILD A CNC ROUTER, THE PLAN DRAWINGS ARE INDECIPHERABLE AND TEXT WITH THEM IS ILLEGIBLE. THERE NOTE REFER MDF PARTS LAYOUT 1 PDF, 2 PDF PLANS & CUT LIST DOWNLOADABLE FROM THIS SITE. WHERE THEY CAN'T FIND THEM?

    Looks like you are trying to screw me out of $30 plus tax as there will be no pdf files forthcoming unless I shell out another $255. Unless you provide the pdf files I will be forced to seek return of funds and will be notifying VISA, GOOGLE PLAY and the BBB doing so until I get satisfaction. If you are not going to honor your book title by providing complete usable information you should remove your book from the market place, or offer it for free. At this point I don't know how you justify screwing your customers like this, but this one ain't going to take it laying down.

    Additional Information:
    Official Buildyourcnc response:
    Thanks for informing us of this issue. Have you looked at this part of the wabsite:
    https://www.buildyourcnc.com/Book.aspx

    The link to the "book" portion of the website is in the footer of every page of the website. If there is a problem with the pdf documents on any page of this portion of the website, please let me know here. Many thanks, Patrick Hood-Daniel

    Click the link to add information to this solution:
    I PURCHASED YOUR BOOK TO BUILD A CNC ROUTER, THE PLAN DRAWINGS ARE INDECIPHERABLE AND TEXT WITH THEM IS ILLEGIBLE. THERE NOTE REFER MDF PARTS LAYOUT 1 PDF, 2 PDF PLANS & CUT LIST DOWNLOADABLE FROM THIS SITE. WHERE THEY CAN'T FIND THEM?

  • I wired my vfd (2.2kw version) and tried test running the spindle. I configured to your specs on this website, only issue is we got an error code. Err 02, do you know what this is? OR have a list of error codes? Thank you

    Can you provide the model number of your VFD?

    Yes, I have the "YL600 - 2S - 2K20"

    It just came with a small booklet that is all in Chinese...

    Click the link to add information to this solution:
    I wired my vfd (2.2kw version) and tried test running the spindle. I configured to your specs on this website, only issue is we got an error code. Err 02, do you know what this is? OR have a list of error codes? Thank you

  • I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

    If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

    If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

    PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
    PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
    PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
    PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
    PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

    Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

    Click the link to add information to this solution:
    I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.