Here is the information we have for the Planet CNC USB controller:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout-Planet-CNC

Click the link to add information to this solution:
Please advise correct wiring from PLANETCNC USB controller Mk3/4 to motor driver.

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

You can find the wiring diagram for the Mach3 USB card on its product page here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Here is a direct link to the diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
I need wiring diagram for motor to driver to usb motion card. I cannot find diagram. I have been unable to get information for a week.

We recommend checking the dip switch settings on your drivers, having the correct microstepping/amp settings along with the steps/unit will help the motors run as effective as possible.
This is a default parameter that we use while we test our motors:
Driver dip switch settings will be at a 1/16 microstepping and 2.7amp (11001100) for x/y-axis and the z-axis will be at 1/4 microstepping and 2.7amp (10101100).

In planet-cnc with increasing the motor speed, you will have to modify the settings in planet-cnc (File/settings/setup) you will modify the initial speed, maximum speed, and the acceleration.
X/Y-axis step/unit: 1422.22 initial speed:500 maximum speed:750 acceleration:25
Z-axis step/unit: 1600 initial speed:100 maximum speed:300 acceleration:25
The initial speed and maximum speed will have to be roughly tested and adjusted per application.
Make sure to adjust the JOG slide bard underneath the axis controls on screen to about 750, to compensate for your x/y-axis adjustments. If left alone the speed will max out at the default setting.

Here is a video tutorial to calculate the steps required depending on your mechanical linear motion components. (

Click the link to add information to this solution:
I bought Nema 24 motors and driver package with usb board. What do i need to have more speed? Cant even jog past 25 ipm without the motor stalling (not having enough torgue)

What mechanical drive system are you using? If your mechanical drive system connected to the stepper motor causes the motor to spin too fast, then you will be reaching the torque limit of the motor under the load of your axis.

Click the link to add information to this solution:
I have a KL23H2100-30-4B motor with a KL-4030 driver and my motor stalls if I set the rapid above 180 imp.

The video showing the hookup of the large motors showed a sequence that was not correct, or I totally misread what was recommended. I hooked the first motor up that way and it would only go in one direction in a very jerky mode. I confirmed that i had hooked it up the way the video showed, disconnected the wiring that runs through to the motor and reconnected it, thinking maybe a cold solder joint was the problem. No good. I finally went to the motor page that showed a different connection pattern. I tried the one that the motor page said to do, and it works smoothly and in the right direction now.

Click the link to add information to this solution:
my motor only goes one direction. I checked all the wiring and it's correct. Any suggestions?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

The parallel breakout board allows for 4 input connections. Each input connection can have an unlimited number of switches, but if you need to separate the switch circuit for, say, all of the home switches, you can use another input pin. There is no need to add another breakout board to add more switches unless you need to use the input pins for totally unique conditions that may or may not be related to CNC functions.

Customer response:
To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on?

Plus, I have a SuperPID. Another pin?

Additional answer:
You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

The GND terminal can be doubled up.

Additional Information:
how about a diagram to reference showing the pin-out to use

Here is the diagram for the parallel breakout board (pins 10 through 13 are used for input):

The circuit is from the GND to the input

Here is the diagram for the Mach3 USB board (pins I1 through I4 are used for input):
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
The circuit is from the V- to the input pin

Click the link to add information to this solution:
Limit, E-stop and home switches: To set up the maximum number of switches set up I would need 2 BOB's, correct? How is this implimented and wired?

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

The breakout board has a relay installed and uses the terminals labeled S, O and P. The following link explains the operation of this relay and how to connect the terminals:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/8/

You will run your power cord (use an extension cord rather than the actual power cord of the router) through the relay using the S, O and P. The P is a general connection and the S is normally closed (S and P is connected when the relay is not engaged) and O is normally open (O and p are not connected until the relay is engaged).

There are three wires in the power cord: neutral (white), live (black) and earth ground (green). You will run your neutral wire (white wire) through this terminal. At some point in the power cord, remove the outer insulator and expose the three wires within. Cut your neutral wire and strip both ends of the cut. Then insert one end in P and the other end in O (normally open), so Mach3 or other control software you are using will engage the relay and the router will turn on.

You will need to setup your control software to turn on the relay using Pin #16 as this is the digital signal pin that controls the relay.

Click the link to add information to this solution:
What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

The motor is creating it's own EMF when you try to turn the shaft manually. When coils are connected (or not connected) to any circuit that is not powered can cause unpredictable results.

The motor freezing from just turning it by hand with no connection is surely the wires touching each other. This is actually how we test if a motor is good or bad. If the motor freezes when two of the wires are touching, that means the motor is functioning properly since the magnets are causing current to flow through that coil opposing the magnet.

Click the link to add information to this solution:
I cannot turn the shaft of my stepper motor. It not even connected to a driver

You can change the direction of a stepper motor's rotation by swapping the A and B coils where the stepper motor is connected to the stepper driver. This may not work with every stepper motor and driver combination.

To do this:
- Turn off all power to the stepper drivers. If this is not done, you will damage the stepper driver.
- Wait at least 1 minute for the power to dissipate from the drivers and power supply.
- Once power is off, remove the wires from the A+ and A- and insert these wires into the B+ and B- respectively. Then insert the wires that were in the B+ and B- into the A+ and A- respectively.

Click the link to add information to this solution:
Is there a way to change the direction of a motor with the motor to driver wiring?

Could you specify which breakout board you have? If you have a parallel port version, be sure that you have purchased the "legacy" parallel port version from Mach4. If this proves not to be the problem, please feel free to email us directly at techsuport@buildyourcnc.com or call 281-815-7701 for troubleshooting instructions.

Click the link to add information to this solution:
I need a resource, we bought 2 redfly systems and mach 4, We put one motor on for the x axis but cannot get it move. Can you direct us to some tutorial?

There is no need to connect a stepper motor to a relay. The stepper motor driver controls the stepper motor completely.

Click the link to add information to this solution:
I have 8 wires wired to my driver in the right places. I need to know how to wire the relay Ken

The EN terminal on the QJ8060 driver and all of our other stepping motor drivers is the enable terminal. We don't use this terminal and the driver will function properly if left unconnected.

Click the link to add information to this solution:
What are the EN connections used for on the QJ8060 motor driver? I notice that your video seems to leave them unconnected.

From the USB controller, the CP+ and CW+ are connected to the 5V terminal. The CP- is connected to the CP terminal of the driver and the CW- is connected to the CW terminal of the driver.

Additional Information:

Click the link to add information to this solution:
Please explain how to connect 2.5AMP stepper motor driver to USB board. All parts are from your store. Thanks

We will make sure that order is changed prior to shipping.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
just placed an order for 2 nema 34 and 1 24 stepper motors i meant to have be 1, 34 and 2, 24 stepper motors. I need to change that before shipping

The KL-4030 is a Keling 3.0 amp stepper motor driver. These are generally pretty robust drivers. You mentioned in the question that it worked for one hour. This sounds like it could be a contact issue with the wiring in the terminals. I would recommend that you check all of the connections. The terminals that are used in these drivers have terminals that are easily used incorrectly.

Make sure to open the terminal all the way using a small screw driver. Then insert the exposed wire into the opening and re-tighten the terminal. Make sure of a good connection by tugging on the wires.

Also, check kthe digital wires that connect from the driver to the control board.

Click the link to add information to this solution:
I have a KL-4030 stepper motor driver that I only have about an hour use on it but seems to be bad already. Has anyone out there had the same problem?

If you purchased the spindle from us, you should have received a little booklet that shows all of the program settings. If you did not receive that booklet, please call us so we can send you this booklet.

If you have the booklet, please let us know specifically what setting you would like to set and we can help.

Click the link to add information to this solution:
I need the drive setting for the 1.5kw spindle drive to work with the spindle motor where do I find them