Yes, we can customize almost any size of a machine. 2'x16' is within the possible dimensions. For a customized machine that you do not see in the "Design Your CNC" section, you will need to contact customerservice@buildyourcnc.com and make the request there.

Click the link to add information to this solution:
I am interested in the "Design Your CNC" page. However I need an extra long table. Is there any possibility of designing a custom 2' x 16' CNC, or can two 2' x 8' tables be combined some how?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

If you would like to see a machine in action, you can go to the forum and make a request in the buildyourtools.com forum.

Click the link to add information to this solution:
I am interested in the blacktoe but want to see on in operarion personally. is there one in lower Michigan. I live in Hillsdale Michigan area.

Dealing with our inverters, they are built with a bit of margin on the input power. For our 220V VFD the margin is from 170-250V 50/60Hz, so running our VFD in your location will not be an issue! Our electronics will not have a issue running at 230V as well.

Click the link to add information to this solution:
Hello. I am interested in the green bull 6X long z CNC machine with electronics. I live in NZ, where the voltage is 230 V and 50 Hz. is it going to be possible to get the inverter to run here? Thanks!

Yes, to build a computer controlled table saw fence, you can try the following:

Assuming that the fence can already move, add a motor on both sides coupled to either lead screw or chain mechanics. Lead screw would be the best solution. The lead screw nuts would be mounted on the fence aligned with the motor shafts at the front and back of the fence.

I would recommend the 425 oz-in stepper motors and 3.0Amp drivers for each motor. You will need a power supply rated for 24 volts. There is no need for a higher volt power supply. Interface the drivers to the computer using a USB interface, or a parallel breakout board.

Stepping motors: https://buildyourcnc.com/category/nema
Drivers: https://buildyourcnc.com/category/driver
CNC Motion Interfaces: https://buildyourcnc.com/category/breakout

Measure the length of travel and get lead screw twice as long since you will need lead screw on both sides. Add a bit more length for space that will be needed for the mounting. Plan as much as you can before purchasing.

Lead screw: https://buildyourcnc.com/item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi
Lead nut (antibacklash nut): https://www.buildyourcnc.com/Item/mechanical-leadscrews-antibacklash-nut-!5-5-starts-10-tpi


Additional Information:
555

Additional Information:
555

Additional Information:
555

Click the link to add information to this solution:
I am interested in building a computer controlled table saw fense. Do you have any products that could help me.. Thanks

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

For all of our kits, it is highly recommended that the instructions are completed read. This will determine if the customer has the ability to take on a project of this complexity.

Depending on the specific blackTooth option purchased, the kits include the following (if the parts is listed in the instructions, it is included in the kit unless otherwise specified within the price option):

- Structural components: Plexiglas panels and MDO structural parts that form the overall machine.
- All of the hardware necessary to assembly the structural components and to fasten the electronics and laser components.
- The electronic components to move and power the machine including power supplies, motors, drivers, interface and computer components if that option was purchased.
- Laser components including laser tube, mirrors, lens, nozzle, air pump and mounts.
- Mechanical components including drive pulleys, bearings, rails, and timing belts.

Click the link to add information to this solution:
I cant find a list or description of what the kits actually contain.. Pictures would be nice befor I spend 2 grand "The BlackTooth will be provided in kit form" is a bit limited.. Thank you

Call again. Most likely, one of my employees were on the line with another customer at the time you called.

Click the link to add information to this solution:
I am interested in order the redleaf system you talked about for my machine, tried calling and mail box is full, no answer. How do I contact you?

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

With our blackTooth kit, if you were to go with our lowest cost machine being $1700. With the parallel breakout board the best new beginner programs you can use, would be Mach 3 and ArtCAM, since it is a good program for beginning users.

Now if you feel a little comfortable with CAD/CAM, I would recommend CAMBAM and is a good overall software since it has a large design screen which allows you to view your design more clearly.

Additional Information:


Additional Information:
I want to avoid the Parallel Port option and go with USB. In that case, is Planet-CNC Software, and ArtCAM the best combination? Does Planet-CNC do the same thing as Mach 3 only with different physical ports?

Click the link to add information to this solution:
I'm interested in buying your blacktooth laser engraver for cutting out inlays on woodworking projects. I am new to laser engraving/cutting, and CAD. What is the simplest beginning software setup available to allow me to cut 2D shapes and letters for inlay work?

You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I live in Australia and am looking at purchasing the Blacktooth laser cutter and engraver. I am wondering what the cost to ship to Australia would be?

Sure, we can send you a replacement LED indicator. Just send an email to customerservice@buildyourcnc.com, include your address and we will send it poste haste.

Click the link to add information to this solution:
The LED Status indicator on the front of my Blacktooth laser is not working any longer. I'm looking to get a replacement but can't seem to find them on your website. Do you sell replacements? Thank you.

The 2.2kW Spindle has many advantages over a standard router such as the Porter Cable. The most obvious benefit to the user is the significant reduction of both dust and noise.

Additional Information:


Additional Information:
What size water source is needed and how long can it be used before it is too warm? Do you have a pressure vs. flow curve for the spindle so I can properly size the water pump?

Additional Information:
I used a small pond pump inside a 5 gallon bucket. I put a little bit of windshield washer fluid in with it to keep anything from growing in it. It's worked great. I've had 1 hour run times with no noticeable increase in spindle temp.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the 2.2 kW spindle. Does it run much quieter than a 2 hp Porter Cable router? You also mention a pump with a bucket of water. How long until the water is too warm to cool the spindle?

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens, and nozzle. You will also need some mechanical parts and some motors, drivers, and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Our spindles have a runout of less than .0001 in, which includes that collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I'm interested in the 1.5 kW (kilowatt) Water Cooled Spindle with Inverter (VFD), I would like to know about the run out of this spindle?

Currently our greenBull can only accommodate a 40W laser tube due to the size and current mounts on the spindle/laser hybrid assembly!

However please contact 281-815-7701 for further assistance with the greenBull machine.

Click the link to add information to this solution:
I am interested in the GreenBull 4x8 CNC machine kit you have; I also wish to get the laser attachment but I was wondering if its possible to have the laser larger than a 40w, say in the 80-150w range?

I will address the two separately (precision and accuracy):

Precision (repeatability):
This is most closely related to the resolution. The blackTooth uses the same mechanical drive (timing belts and pulley) of the same ratios and specifications, so the two machines will be the same in this respect.

Accuracy:

The output of the machine (the final physical work) matching the input given to the machine (the design data or instructions for the machine to product the physical work. This has to do with both resolution and how well the machine will hold up over time and through environmental changes.

With that said, both machines have very similar attributes in mechanics and structure. The overall structure is made of MDO (Medium Density Overlay) and has a very low coefficient of linear expansion with regards to temperature change, so accuracy will not be affected in any appreciable manner over time with the two machines. The Vertical Laser XL does use more industry standard rails to hold the heavy gantry, but this will be differ appreciably since the blackTooth will exhibit rigidity by virtue of its size.

It really is best to consider the application and size as the main aspects of deciding between these two machines.

Hope this helps.


Additional Information:
We're looking at getting the vertical so we can run both large and small jobs on the same machine. It sounds like running a small job on the vertical (using a positioning jig) would provide results at least as
good as running the same job on the blacktooth. Does this sound about right?

Click the link to add information to this solution:
Is there any precision or accuracy difference between the vertical and blacktooth lasers?

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.