https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

If you ordered lengths of rail that is not to your specifications, please give us a call and we will replace your order immediately.

Click the link to add information to this solution:
I ordered some hiwin cut to size, I ordered two 17in pieces and received a 34in instead. what can we do about this, am I SOL?

Do you believe the source backlash is at the nut, or somewhere else?

Click the link to add information to this solution:
Hi Guys, I fitted new ball screws to my mill as part of a cnc conversion. I have about 0.15mm backlash in both the x and y axis. What would you recommend to remove the remainder of the backlash mechanically? Thanks in advance.

Are you trying to use the MPG (tab), or the keyboard for jogging the motors? You mention 0,0,0, are you trying to home the machine with the "ref all home"?

If you cannot move the motors with the keyboard, check if the jog is enabled.

Click the link to add information to this solution:
[596] I have my motors and limit switches working correctly but I am unable to get any movement from the 'jog step' so that I can set 0,0,0. What should I check

You can find the required components for our scratch build CNC here(https://buildyourcnc.com/cnckitintro.aspx).

Lead Screw needed will be:
X-axis: 52 Inches
Y-axis: 32 Inches
Z-axis: 14 Inches

These will be the bearings that are specified that will be needed:
Bearings 1/2" Inside Diameter - 6
Bearings 5/16" Inside Diameter - 24

Click the link to add information to this solution:
Hi, I need the lead screws and bearings for the 4' x-axis, the 2'(?) y-axis and the 1'(?) z-axis as specified in the book 'Build your own cnc'. I am not sure which to order on your website. Thanks

We just received our new inventory of motors and that specific stepper motor ski came back with only one shaft. I’m not at the office to look at this inventory, so if that is true, they will all be single shaft. We may have other stepper motors with included rear shafts, but I will have to see on Monday.

If I don’t have the double shaft, we will provide a refund upon receipt of the motors. My apologies for this error.

Additional Information:
Hi, I'm sending these motors back today. As I understand you, you might have some motors from the previous lot still in stock, and these would be double shaft but otherwise you don't have any and won't be getting any. If you do have two double shaft versions of this motor please send them; if you don't have two of them please let me know--today if possible--so I can start looking elsewhere. Thanks, Ted Armen

Click the link to add information to this solution:
we just received two nema 11 stepper motors per our order--USR2-2, however they are single shaft, we need double shaft, I thought that's what we ordered. We're sending them back, let me know if you do have the double shaft version and I'll try again to order them. I notice the model number on the motor ends in "A", where the packing slip shows "B".

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

The blackTooth laser power supply will use 4 - #8 x 1" screws, and 4 - #8 nuts. As stated on step 10 here (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/10/)

Click the link to add information to this solution:
I am building a blacktooth. I don't see in the instructions what screws are meant to fasten the power supply to the wood. The instructions show how to wire it but I don't see where it says which screws to use. I don't want to guess and end up being short later. Thanks. .

The blueChick v4.2, is accurate at 1000's of an inch, with the roller chain, the v3.0 with the timing belt will increase the accuracy by 5%-10%, but to the expense of structural integrity.

Additional Information:

Click the link to add information to this solution:
If I wanted to use the blueChick for isolation routing, what accuracy could I expect from v3.0 and v4.2?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

Planet CNC has the option to turn off these outputs on your USB board. Under the File/settings/Pins. You will have Spindle (M3,M4,M5) Coolant (M7,M8,M9) as available output pins. On the drop down tabs for these output pins you will have this option ( --- ), if selected it will turn of that output pin in your board and you will get not voltage change in the pin.

Additional Information:
Cannot activate output in mkx

Click the link to add information to this solution:
On the USB controller I am unable to get voltage from the Mist relay block on the board. The Flood and Spindle produce a voltage change correctly. Is there a setting I am missing?

It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

Click the link to add information to this solution:
hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

Please explain what the number 500 is? Thanks

Click the link to add information to this solution:
ReplicatorG says my white ant extruder is at 500 or more. I've replaced the electronics on the printer but that hasn't fixed it what else can I do?

The best place to find information and step by step instructions for Mach4 is to use the manuals provided by MachSupport.com.

Here is a link to the PDF manuals for Mach4: http://www.machsupport.com/help-learning/product-manuals/

Click the link to add information to this solution:
I purchased Mach 4 control software and am in need of a very elementary tutorial on set up. I am extremely new to this and need step by step help. Thanks

Here is the answer to your first questions regarding the blueChick motors:
https://buildyourcnc.com/FAQ/9024

The shipping of the blueChick CNC will depend on if the machine is assembled or not. There is a duty for international orders, but I am unsure of the cost in other countries other than the US.

Thanks

Click the link to add information to this solution:
What are the specs for the stepper motors on the Bluechick? How much for shipping to Toronto, ON, Canada? Is there duty for shipping to Canada?