That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Did this spindle come with a 110V 1.5kW VFD?

Additional Information:
The reason I ask is because the 220V 1.5kW spindle may work well with the 110V 1.5kW VFD. I believe we did the test prior to shipment.

Additional Information:
I have a 110V HY01D511B VFD already. I did not know they would work together. I will give this a try.

Additional Information:
If you did't get the VFD paired with the spindle from us, then I would not connect the 220V spindle with your VFD. Let me ask my technician and get back with you.

Additional Information:
My technician said that it should work since the 220V 1.5kW spindle worked with our 1.5kW 110V VFDs.

Remember to seek the advice and guidance of a professional electrician when connecting these types of high powered devices.

Additional Information:
Do you have any info on the settings? I would rather buy a pre-configured VFD from you if you don't have the settings for my HT since I have already fried one spindle because of lack of documentation from the manufacturer. If you can setup a VFD that works with the spindle you sent at 110v input voltage I would be fine with the extra expense.

Click the link to add information to this solution:
I ordered a 1.5KW 110 volt spindle. I just received the box and the spindle clearly says on the foam packaging and the side of the spindle that it is 220V. I think you shipped me the wrong spindle

Our 1.5/2.2kW spindle will work with both setups, in our wiring diagram it is more seen as the Euro/AUS-style, however you can do the same thing with the North American style as well. Also depending on if you have single or three phase 220V, you can use pins R, S, T. A manual will arrive in the VFD box, which will have further information and diagrams.

Please seek a certified electrician if you are unsure of any aspect in wiring the spindle or VFD, since wiring to main lines will require wiring of the plug and main lines to the inverter and to avoid any damage or injury's while installing the 1.5/2.2kW spindle and VFD combo.

Click the link to add information to this solution:
On the wiring diagrams for the 220v inverters I noticed that there is one hot (220) a neutral and a ground. Will the inverter work with the American split phase system? Hot (120) hot (120) ground?

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

Spindle comes with 1/4" collet.

"All of our spindles come standard with a 1/4" collet. The 2.2kw, and 4.0kw, can be upgraded to a 1/2" collet with a separate purchase"

Click the link to add information to this solution:
I just purchased the 2.2 kW water cooled spindle. I also ordered a 1/8" collet to go with it, since I assume it comes with a 1/4" collet. Is this correct?

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

For the 2.2kW Spindle you would need the ER20 1/2" Collet.

Click the link to add information to this solution:
What 1/2" collet and nut do I use for the Greenbull with the 2KW spindle? I want to order the Onsrud Spoilboard surfacing cutter.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I bought a gantry mounted spindle water cooler kit. I cut off the plug terminal on the end. There are three wires and it is labeled as a 12 V DC motor. How do I wire it to the power supply? No combination of connections seems to work. the fan runs fine. it

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I bought a gantry mounted spindle water cooler kit. I cut off the plug terminal on the end. There are three wires and it is labeled as a 12 V DC motor. How do I wire it to the power supply? No combination of connections seems to work. the fan runs fine. it

The 2.2kW Spindle has many advantages over a standard router such as the Porter Cable. The most obvious benefit to the user is the significant reduction of both dust and noise.

Additional Information:


Additional Information:
What size water source is needed and how long can it be used before it is too warm? Do you have a pressure vs. flow curve for the spindle so I can properly size the water pump?

Additional Information:
I used a small pond pump inside a 5 gallon bucket. I put a little bit of windshield washer fluid in with it to keep anything from growing in it. It's worked great. I've had 1 hour run times with no noticeable increase in spindle temp.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the 2.2 kW spindle. Does it run much quieter than a 2 hp Porter Cable router? You also mention a pump with a bucket of water. How long until the water is too warm to cool the spindle?

When did you purchased the VFD and spindle? We only started this after the date of the instagram post that offered this added service.

Additional Information:
I purchased it July 16, 2020 however due to all the 2020 issues, I'm just now completing my CNC and hooking up the VFD and Spindle.

Additional Information:
The service started on Sept 23, 2020. Your order was prior to that.

The soldering is straightforward. If you wish to have me provide this extra service, feel free to send the unit back with the cable and I will solder the cable and do the parameter check and test the VFD and spindle.

Additional Information:
When I purchased my VFD and Spindle, I forgot to purchase the wire for the spindle. I had an electrician run a 220 line and hook up the VFD. But I don't have the wire for the spindle. I'd like to get the one you recommend and just pay you for another connector and the soldering.

Additional Information:
Can I purchase the one you spindle wire you recommend and just pay you for another connector and the soldering.

Click the link to add information to this solution:
You state "If you purchase cabling, we will solder the cable to the spindle and connect the cable to the VFD." I didn't see that when I purchased my spindle and vfd. If I place an order for the wire and another female adapter, will you please solder the connector to the wire?

The squeal you hear from your spindle running at low RPM is probably not associated with bad bearings (I guess it depends on the sound). All of our spindles running at low RPM has a distinct sound, probably caused by the coils and the magnets.

Click the link to add information to this solution:
Hello, I have a chinese 2.2KW spindle that is nearly new purchased with a CNC I bought while in china, I have noticed at lower RPM there is a distinct squeal. Does this indicate bad bearings?

You may want to try using a ferrite core or an inductor in addition to the shielded cable. Also, make sure you are grounding the shield at both ends. Even though this is not high frequency, grounding the shield at both ends in a motor scenario may help. Also, try to reduce any parallel wire runs.

Click the link to add information to this solution:
[575] Hi, I plug HY 220v spindle on the board. It work, but the is a unstable frequency on the spindle. I put shielded wires from BOB to Inverter, and from Inverter to Spindle. But the problem still there. I read that I have to put a Analogue PWM, is that true, or I have problem with my wires... Thank you

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.

The ring inside the nut is purposely machined in this way to allow movement for the collet. Try threading the nut counterclockwise a little bit until it seems to be flush on the spindle extension. This should ensure the collet nut will thread correctly without stripping the threads on the pipe.

Click the link to add information to this solution:
I purchased a 220V spindle with invertor last week and the ER20-A Clamping nut appears to milled incorrectly. I installed the spindle for the first time last night and was unable to screw the nut any distance with a bit inside. Looking inside the nut, there is a machined ring that is visibly off center.

The 2.2kW spindle will accept up to 9/16" (a little over 1/2") end mill shanks down to very small diameters (any size that ER-20 will accept). The 1.5kW spindle has a reduced collet size and will only accept up to 5/16". The 1.5kW will accept ER-11 collets.

Click the link to add information to this solution:
Does the spindle accept different collet sizes, or do I need to purchase different spindles that will accept different collets?