Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

Is the signal gnd on the laser power supply connected to a gnd on the breakout board? Do you hear a high pitched sound, like a TV set with an antenna getting interference, but with a high pitch?

Click the link to add information to this solution:
OUR FIRST ATTEMPTS WERE WITH THE PLANET-CNC SOFTWARE, GOING THROUGH USB BOB. NO PROBLEM GETTING X & Y AXIS TO MOVE BUT UNABLE GET ANY ACTIVITY ON Z AXIS. WE THEN INSTALLED MANUAL SWITCH BETWEEN 5V AND TL, JOY. DISCONNECTED BOB FROM TH, MOVED OVER TH TL STILL

It is likely that if your Spindle's collet is ER11 specification than other size ER11 collets will work with your spindle.

Click the link to add information to this solution:
I bought a 1.5kw spindle that came with the ER11 6mm collet. I found collets for 1/4" and 1/2" but will these work with my existing nut? I see there is a nut for sale but it says its just for Bosh and Porter Cable etc.

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

After you purchase the license, we provide you with the license file. That file needs to be manually copies to your mach3 folder. The mach3 folder is usually on the C: drive (C:\Mach).

Copy the file that was emailed and copy it to the c:\Mach3 folder.

Go to the about menu option in Mach3 and confirm that your name is on that dialog box.

Additional Information:
My name is not on the dialog box

Additional Information:
Its mach 4 dumass

Click the link to add information to this solution:
I reciently purchased Mach 4 and sowenloaded the license. After creating the profile and working with the program it is still in the demo mode. The drop down tells me that it is sucessfully installed. Please help.Thanks

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
I'm new to this and was wondering if I connected something incorrectly... I followed the schematics found on this site for wiring. I purchased the heavy gantry kit with the USB power option. All my lights come on and motor shafts resist turning but, I cannot get movement from Mach3. How do I test my equipment to see if I've damaged anything?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

You may want to try using a ferrite core or an inductor in addition to the shielded cable. Also, make sure you are grounding the shield at both ends. Even though this is not high frequency, grounding the shield at both ends in a motor scenario may help. Also, try to reduce any parallel wire runs.

Click the link to add information to this solution:
[575] Hi, I plug HY 220v spindle on the board. It work, but the is a unstable frequency on the spindle. I put shielded wires from BOB to Inverter, and from Inverter to Spindle. But the problem still there. I read that I have to put a Analogue PWM, is that true, or I have problem with my wires... Thank you

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Fusion 360 is a program that allows you to design in a parametric 3 dimensional environment and also provides a great CAM toolset. Fusion 360 will produce the gcode with the CAM capabilities. The gcode is used to move the machine in various ways in order to mill the material; however, software is needed to interpret this gcode and cause the machine to move according to the gcode instructions. This is called control software. So Fusion is CAD/CAM, and you still need "control". Mach3 is one example of control software for milling and is highly recommended.

Install Mach3 onto the computer that will connect to the redFly(CNC electronics), then configure the Mach3 parameters for the machine (motor tuning, plug-ins, inputs/output, etc.). Home the machine, load the gcode into Mach3 and the machine will move according to the gcode.

A word of caution, since you are new to CNC machines, make sure you familiar yourself with the machine and the movements of the machine specific to how the gcode is arranged with respect to the coordinates of the machine. Try with very simple gcode until you get a very good understanding of how the machine will move.

Click the link to add information to this solution:
Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?

Please amke sure that you have performed the calibration. Check in the control panel used for manual control, and set the temperature to 205 degrees Celcius, and make sure the program is seeing the temperature rise. Once the temperature has reached 205, manually jog the feed for the extruder and make sure you are extruding evenly. Make sure all your bolts are tight, and that you have your machine on a level surface. You may try placing your machine on a board, and using some "L" brakets against the bottom feet area, to stablize the machine from torquing. Also, make sure your extruder head is clean and free of debris. If all of this does not help, you can give us a call and we will see if there is anything else we can figure out that may help.

Click the link to add information to this solution:
I have my whiteAnt extruding and printing but the prints seem a bit "spidery". The the filament strands are not tightly knit together and there are gaps. Are there adjustments that should be made for temperature, speed and distance to accomodate the thinner extrustions of the MK7 extruder?

When did you purchased the VFD and spindle? We only started this after the date of the instagram post that offered this added service.

Additional Information:
I purchased it July 16, 2020 however due to all the 2020 issues, I'm just now completing my CNC and hooking up the VFD and Spindle.

Additional Information:
The service started on Sept 23, 2020. Your order was prior to that.

The soldering is straightforward. If you wish to have me provide this extra service, feel free to send the unit back with the cable and I will solder the cable and do the parameter check and test the VFD and spindle.

Additional Information:
When I purchased my VFD and Spindle, I forgot to purchase the wire for the spindle. I had an electrician run a 220 line and hook up the VFD. But I don't have the wire for the spindle. I'd like to get the one you recommend and just pay you for another connector and the soldering.

Additional Information:
Can I purchase the one you spindle wire you recommend and just pay you for another connector and the soldering.

Click the link to add information to this solution:
You state "If you purchase cabling, we will solder the cable to the spindle and connect the cable to the VFD." I didn't see that when I purchased my spindle and vfd. If I place an order for the wire and another female adapter, will you please solder the connector to the wire?

Is this CNC related. If so, what controller are you using?

Additional Information:
I'm using the Mach 3/USB CNC interface board, with the Mach 3 software.

Additional Information:
Does the LED on the controller light up, or blink?

Additional Information:
I believe I've corrected the issue. I found that their are 2 spring like tabs on the female USB port. And take a sharp point like on a compass and gentle raise those tabs a bit. This tighten up the connection, and I never received an error from losing connection.

Click the link to add information to this solution:
It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

To determine the status of your order, simply log in and click on the "[My Account]" link at the top of the page. If you purchased as a guest, you will need to call the office to determine the status and get the tracking number for your order.

The office phone number can be found by clicking "Need Help?" is located at the top right of all buildyourcnc.com web pages.

Click the link to add information to this solution:
I placed an order for a 4th axis with tailstock on Wednesday and was just wanting to check on the shipment status. I'm needing the item early next week and need to confirm that it will arrive in time. Thank you.