CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

The greenBull kit (not the assembled) will need the table (the rails for the table is supplied), wires/cables for the stepper motors and stepper motor drivers, smaller gauge wires for digital wire connections (limit switches, drivers to control interface, etc), wires for the spindle connection to the VFD, tubing for water flow to and from the spindle, and a pump and reservoir (we are just about to introduce a small pump/reservoir/radiator/fan system for use with the spindle. The VFD/spindle, stepper motors/drivers and interface board are included.

Click the link to add information to this solution:
If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?

I'm not sure I understand the question. You are looking for spacers or sprockets?

Additional Information:
Nevermind, I found my answer. Thank you

Click the link to add information to this solution:
Since you don't sell the hardware only package for the Blackfoot 4'x8' can you tell me what items I should look for for the chain sprockets, spacers to mount them to the 1/2" rod, and chain? All the other parts I can source from elsewhere

What interface board are you using? Typically, this will be an issue with the computer that MAch3 is installed. The only other component that may affect this would be the interface between the computer and the machine.

Click the link to add information to this solution:
mach3 freezes in the middle of a run, I don't get any message. I have press reset and then the jog buttons work. I have to reset the zero and start from the last line when the machine stopped. It happens mostly during the finishing part of the g-code file

If your Z axis is moving in the opposite direction, go into Mach3, click on config, ports & pins, then click on the motor outputs tab. You will see the axes labeled on the left and the parameters labeled on the top of this dialog box. Toggle the dir low active for the z-axis.

Additional Information:
What if I'm having the same issue on a different axis?

Additional Information:
You can follow the same procedure as with the z-axis. When you get to the motors outputs tab, toggle the dir low active checkbox for the axis that you would like to change.

If you are using another control program, let me know and I will add the recommended action here.

Additional Information:
Girbl

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:

Click the link to add information to this solution:
My Z-axis seems to be reversed on a fully assembled machine... I've tried reversing it in the config settings on Mach 3, but to no avail. What do I need to do? IS this a wiring issue that was not done correctly at the factory?

Your deduction of the power supply at fault is probably correct. When you attempt to power the power supply, check the V+ and V- (COM) with a multimeter on the DC setting. You should measure 36 volts.

If there is no voltage on the V+ and V- (COM) there should be a fuse inside the power supply that you might want to check. Also, while you in there, check the electrolytic capacitors. Electrolytic capacitors have a finite lifespan much shorter than other components and are often the cause of many problems with all electronics.

Please let us know what you find.



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
My machine stopped today (after many fun filled hours of operation in the last 3+ years). I suspect the 36V 8.8 amp power supply as there is no power to the stepper motors. Is there a breaker to check, or do I need to get another power supply? Should I assume the stepper motors are OK?

My apologies for not getting back to you. We always answer the phones during business hours, so I would try that first. Our emails on Monday generally is stacked up as we are closed during the weekend. We can try your g-code here. Please send the g-code to the techsupport@buildyourcnc.com email address and we will test the code to see if it works.

By the way, do you get movement on the planet-cnc UI screen?

Additional Information:
The program starts and runs normal. I have all the correct movement on the mill and the UI screen. Then one of two things happens. It either stops and resets all axis to zero in the middle of the part or it freezes in the middle of the part. When it freezes, it is not moving on the cnc or the UI screen. Sometimes after a freeze it will come up with an 'IO timeout error', but the only way to clear is to unplug USB and start over.
I will send my settings and g-code files over tonight. Please be sure to load my settings when running the g-code. No movement of the cnc is necessary as the controller will do these issues without power to any drives and just the USB board connected, on my board at least.

Click the link to add information to this solution:
I have a MK1 board that I just got running and I am having issues. Do you have an MK1 board at your shop that I can send you my G-Code to run? The freexing/zeroing in the middle of the program issue happens even with no step drives attached to the board.

You can use either 1" x 1" x 1/8", or 1-1/4" x 1-1/4" x 1/8" angle on the table sides. The BRAs should all be 3/4" x 3/4" x 1/8". The Y ans Z axes should use the 3/4" x 3/4" x 1/8" angles.

Click the link to add information to this solution:
In the Build your own CNC machine book, You said you use 1 1/4" angle on the main table but 1" would be better. So my question is Should I use 1" angle on the main table (4' length) and 1 1/4" angle for the BRA's and other rails?

To have a complete kit, these will be the following items that are most common to add to the order:
Motor Cable (20 AWG 4 conductor) = 30Ft (X-axis 9Ft, Y-axis 10Ft, Z-axis 11Ft)
Spindle/Inverter 2.2kW either 110V or 220V
Silicone tubing 1/4" ID - 3/8" OD (desired length or 24' to have your water cooling container right next to the machine)
Water pump either 110V or 220V
Cable carrier (cable management), default length: 5Ft.

Other accessories:
Different collets 1/2" or 1/8"
End Mills

Please call: 281-815-7701 for further assistance on purchase

Click the link to add information to this solution:
I'm intending to order a black toe machine for shipping to New Zealand. Postage will be a very significant part of the cost. What components do people buy in follow up ordets that may make sense to add to my order?

I would first check the mechanical parts to ensure smooth motion. Is your machine bogging down during cutting or jogging/rapids?

You can increase the voltage to gain a higher speed for rapids/jogging, but make sure the driver can handle this voltage. There should be a max voltage on the driver label.

If the bogging down is happening during cutting, either reduce the cutting depth or switch out the drive and motor for the axis that is giving the problem.

Click the link to add information to this solution:
[129] I have a Blackfoot and have a question about the power supply. I currently have a 36V power supply and my machine bogs down, would a 70V or something like that help, or will that blow up my machine? thank you!

Unfortunately we no longer include or sell our CNC plans for none of our machines. We will be here to assist you if any parts wear over time, and will be able to replace the parts if needed.

Charges may be subjected due to time of purchase and cause of wear.

Click the link to add information to this solution:
If I purchased the blackFoot 4x8, do you include the plans for the machine itself, in case I wanted to replace a piece of it due to wear?

Sure, email me at customerservice@buildyourcnc.com and I will send you a replacement for a minimal fee. I now use HDPE for that part. The HDPE holds up much better.

Click the link to add information to this solution:
I have a Blackfoot 4x4 v2 chain drive. my Y plate is broken . do you sell just the Y plate or can I buy just the Y plate spec plan? I love this machine Its great. my name is Jeff Krug I bought the complete package and electronics from you guys. thanks

The jog speed of the blackToe is 1000 - 1500 ipm (inches per minute). I generally set this to about 700 ipm just to be safe and 700 ipm is plenty fast for most scenarios. The cutting speed will depend on the tool (end mill) that you will use for the application, the material being used and whether a spindle or router is used. In a scenario that a spindle is used and cutting relatively hard plywood at 3/4" full depth using an Onsrud 1/4" diameter compression end mill, you can cut at around 100 - 300 ipm. Using a router would be only half the speed and cutting depth due to the poor torque.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
What is travel speed of the blackfoot machine ?? I read in a forum somewhere that it's around 100inches/minute. Is that accurate ??

What we intend our customers to use for wiring the motors to the drivers will be 4 conductor 20 AWG cable, now for the PSU to Drivers; 16-18 Gauge wire should be used, and drivers to BB(Breakout Board) should be a 24 AWG wires.

Click the link to add information to this solution:
In my 4'x8' Blackfoot rig, there is a maximum wire length of 16" between drivers, breakout board, and power supply as well as a maximum wire length of 10' from drivers to motors. What AWG wires should I use to connect power supply to drivers, drivers to motors, and drivers to breakout board?

Use a clamping collar (if you are using an ACME lead screw) or a couple of 1/2 nuts (if using an allthread) against the bearing to keep the bearing in place and make sure there is no axial play.

Click the link to add information to this solution:
How do I secure the non-motor end of the lead screw for my 'Book' machine build? Does it just sit inside the bearing or do i use a nut to lock it in place? I did not see any instructions for this in the book.

Most likely, the driver is not receiving the high or low signal for the direction terminals. The way direction works for an axis is the controller will output a high signal (5V) for one direction and low signal (0V) for the opposite direction. If the signal is always at one signal, say 5V, whether it is commanded in one direction or the other, then the axis will only move in that direction.

To solve this problem, make sure that the wiring is secure at both ends (from the controller to the driver). Also, make sure the Dir+ and DIR- are both wired correctly (i.e. the Dir- is connected to the signal gnd on the controller and the ZD is connected to Dir+ on the driver.

You can use a multimeter to determine the voltage at the ZD terminal by:
- setting the multimeter to DC voltage (the V with a straight line, or dashed line above the V)
- place the black lead on the gnd terminal
- place the red lead on the ZD terminal
- press the page up button and check the voltage
- press the page down button and check the voltage.

You should see the voltage change from 0V to 5V or vice versa.

Click the link to add information to this solution:
Hi I have just set up my machine using a mach 3 USB board I can only get the Z to go in one direction Y and X are Ok I have check wiring and looked at video over and over what have I missed??

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I wired my vfd (2.2kw version) and tried test running the spindle. I configured to your specs on this website, only issue is we got an error code. Err 02, do you know what this is? OR have a list of error codes? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you