Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

Yes, you can use a conductive metal to serve as a zeroing block for the Z axis. All you need to do is connect the block (conductive metal) to one of the 4 inputs on the controller. The end mill must be connected to the DCM terminal (the GND of the 24V power supply) of the controller. In the inputs dialog box (config-ports and pins-inputs). Under the probe line, enter port 3 and the pin used for the block.

Click the link to add information to this solution:
[575] Hi can I use a zeroing block with mock three interface board and do you have one I can purchase and directions on how to set up

Yes, the blackTooth actually has a base that is open, so you can set the blackTooth laser cutter on a surface that is depressed as much as you need so you can accommodate a work piece with very large heights.

Click the link to add information to this solution:
I'm considering the purchase of your Blacktooth laser. I will be engraving on my wood blocks that are two inches in thickness. Will the Blacktooth accomodate this thickness material?

Sure. You will need the proper mount for the laser tube and a mount for the power supply in relatively close proximity to the laser tube. If you have one of our greenBull CNC machines, you can use the laser/spindle head that we offer.

Click the link to add information to this solution:
Can I just purchase a laser head to replace my router when all I choose to do is print or copy a photo

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I just wanted to know what I can expect to pay to build the blackFoot 4'x8' CNC machine, excluding computer, software and router? Is the kit complete or do I have to purchase additional items to finish?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

You will probably have post processors like the following listed:
Mach2/3 ATC Arcs (inch)
Mach2/3 ATC Arcs (mm)
Mach2/3 Arcs (inch)
Mach2/3 Arcs (mm)
Mach2/3-WrapX2A ATC Arcs (inch)
Mach2/3-WrapX2A ATC Arcs (mm)
Mach2/3-WrapY2A ATC Arcs (inch)
Mach2/3-WrapY2A ATC Arcs (mm)

If you have an Automatic Tool Changer, use the post processor with the ATC in the name. For most applications and if you don't have an ATC (automatic tool changer), use the Mach2/3 Arcs (inch) or (mm) post processor.




Additional Information:

Click the link to add information to this solution:
How do I determine what post processor I have on my shop built CNC. There are about a million to choose from on Vcarve Pro

If you have an existing PC with a parallel port you will not need to purchase the onboard computer system on the blackTooth laser cutter and engraver. You will want to purchase the blackTooth laser engraver that comes with the parallel interface (breakout board). If you have an existing CNC machine that is being used with this PC, you can disconnect the CNC machine and connect the blackTooth to this PC. You will want to have two configurations for your control software.

Additional Information:
We have a version of the blackTooth that is 110v and 220v. We generally determine which is sent according to the requirements of the customer and in what country they live.

Additional Information:
20

Additional Information:
Parallel Port Configuration BIOS settings and Mach 3.

Click the link to add information to this solution:
I'm interested in purchasing your black tooth laser engraver and am curious what setup to get. I already have a cnc wired via parallel port to my PC. Do I need to purchase the black tooth laser with the integrated computer or can I just disconnect my current cnc's parallel port and connect it to the black tooth laser engraver? Also is the black tooth 110v?

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

Yes, you will need the Mach4 legacy plugin to make the parallel port and Breakout board work.

Click the link to add information to this solution:
Do I use the blue brew BOB that I purchased in conjunction with the Mach 4 PPL Plug-in provided with Mach 4 software when I purchase It?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

Our electronics and plug and play systems can be used with any industry standard software, including but definitely not limited to the Vectric line of software.

Click the link to add information to this solution:
I am getting ready (within a week) to purchase your lug in play controller kits... The software I want to use is Vectric. I notice you talk about Mach software and sketch up. Be fore I purchase I want to make sure I can use what ever software I want... Thank you for your time. Pam

Lidar com nossas placas de desagregação , o USB BoB usará Planet CNC como o seu software principal , eo BoB Parallel usará Mach 3 como seu software principal.

Para calcular o transporte, adicionar os itens ao seu carrinho e imprensa transporte calcular.
Você recebeu todos os custos de envio disponíveis e métodos.

Click the link to add information to this solution:
BOM DIA . QUAL SOFTWARE ESTA PLACA INTERFACE RODA? MORO NO BRASIL. QUANTO CUSTA O ENVIO DE 01 PLACA.

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

TIR specifications for the ER-20 collet used on 2.2KW Spindles is .0004 inches.

Click the link to add information to this solution:
Hi, I'm considering buying one of your 2.2 KW water cooled spindles. What is these spindles run out ?

Yes, the blackTooth laser can cut .05 inch plastic. Generally, it can cut non-metallic materials up to about 0.25 inches. Video of an early test of the blackTooth is available on our website at https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/104/. There are also several posts of the blackTooth in action at buildyourtools.com.

Click the link to add information to this solution:
Regarding Blacktooth laser cutter, can 5 is cut .050 clear plastic and can I have sample pictures? Dpongos@gmail.com

You can call us, send an email, or pose the specific question on this customer service live that pertains to the issue that you are having.

Click the link to add information to this solution:
Im having software setup problems with my backtooth (mach3) and i seem not to find a solution in the forum. what can i do?

I have not heard of different versions of g-code, but ArtCAM would be able to give you the answer to this question, if their software is specifying that there are different versions.

Additional Information:
20

Click the link to add information to this solution:
I'm using ArtCam with my Black Toe. What Gcode version do you choose to work with EMC2