Yes, I can configure a system that contains a relay and solenoid to control air pressure and adding a second probe for tool height.

Click the link to add information to this solution:
[823] Do you know how to connect a second Probe for tool lenght and Relais for Air pressure ?

We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

Additional Information:
Meant to say pulleys, not pullies.

Click the link to add information to this solution:
Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

We just don't make enough on our machines to justify any discounts. We try to offer everyone the same low price.

If I can help in another way, please let me know.

Click the link to add information to this solution:
DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

We are working on getting these on the blackTooth page


Additional Information:
Ok, thanks. Do you use a separate 24V P/S for the supply voltage on the AWC708C or tap into the stepper motor P/S?

Click the link to add information to this solution:
Do you have instructions how to mount the AWC708 DSP on the blackTooth?

1) Make sure to setup Primary partition:

Primary
Beginning of this space
Ext4
Mount point: /
and Swap partition:

Logical
Beginning of this space
Swap area using "Something Else"

2) get and install updates and upgrades

sudo apt-get update
sudo apt-get upgrade

3) get raid software

sudo apt-get update
sudo apt-get install mdadm

4) setup RAID

a) if raids haven't been setup:
sudo mdadm --create /dev/md0 --chunk=256 --level=0 --raid-devices=2 /dev/sda /dev/sdb

b) if raids are setup, but just have to be reassembled:
sudo mdadm --assemble /dev/md0 /dev/sda /dev/sdb

or

mdadm --assemble --scan

Click the link to add information to this solution:
How to setup RAID on Ubuntu

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

I like to use a 3/8" drill bit to create the holes on a table to mount the rails to give the rails a bit of wiggle room to adjust the alignment of the rail.

Click the link to add information to this solution:
Attaching the aluminum rails to the table. Do you use a 1/4" or 5/16" drill bit?

If the VFD is presenting an ER 4 error, the VFD is most likely damaged. The VFD will either need to be serviced or you will need to purchase another VFD. The latter is probably the less expensive option, unfortunately.

Additional Information:


Additional Information:
i had that error and found a power in wire touching and fixed and started and all was good.
good luck

Additional Information:
i had that error and found a power in wire touching and fixed and started and all was good.
good luck

Additional Information:
i had that error and found a power in wire touching and fixed and started and all was good.
good luck

Additional Information:
i had that error and found a power in wire touching and fixed and started and all was good.
good luck

Click the link to add information to this solution:
I bought a 2.2 Kw spindle and YL620 A-2 from you and am getting an ER 4 message. How do I fix it?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE VFD TO SPINDLE?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
HOW DO YOU CONNECT THE INVERTER TO AC?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
HOW MUCH MOTOR CABLE DO I NEED FOR A BLACKFOOT

The wire that we sell for the limit switch wiring is here: https://www.buildyourcnc.com/item/3d-printer-component-cnc-electronicsandmotors-cable-wire-3-conductor-22-awg-wrcon-cablewire3conductor22awg

This is shielded cable to make sure there isn't any external interference with sensitive components and long wires associated with limit switches. This is necessary due to the interference caused by the motors on a CNC router and the milling process.

Additional Information:
So unshielded is cool. That's what I was curious about. Cheers.

Additional Information:
Absolutely. It's really the only type of cable I would recommend for connecting limit switches.

Click the link to add information to this solution:
Do you sell 22 to 24 AWG stranded and shielded for wiring of the limit switches and E_Stop?

You can find the wiring diagram, and technical specifications for the NEMA 23 motor, on it's product page, found here,

https://www.buildyourcnc.com/Item/electronicsAndMotors-nema23-100ozin-newbiehack-motors-stepping_motors-100_ozin

There is a datasheet below the product description. This image will expand to be easier visible once clicked on.

Click the link to add information to this solution:
Which power supply, 36V/8.8A or 24V/8.3, to drive one Nema 43 stepping motor?

The NEMA 43 motor we stock has a 5.5A draw, which we recommend to pair with our 6.0 amp driver and 36V 8.8A Power Supply.

Click the link to add information to this solution:
Which power supply, 36V/8.8A or 24V/8.3, to drive one Nema 43 stepping motor?

Yes, this is a must. You can attach the spoil board on the machine with screws, or you can setup a clamping system. We just screw it down.

Click the link to add information to this solution:
DO YOU TYPICALLY PUT SPOILER BOARD ON TOP, IF SO HOW ATTACH IT?