Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
Since the machine is metal, our larger motors would be highly recommended.

We have not done this conversion, through research is recommended.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

I don't see anything in the datasheet for the relay that indicates an overheat condition. While the relay is engaged, the power consumption is 400 mW and I don't believe this is enough to raise the temperature faster than the heat dissipation from the metal on the leads through convection or radiation outside of the rated temperature working ranges providing that you maintain an ambient temperature range within -40°C to 85°C (with no icing or condensation).

http://www.omron.com/ecb/products/pdf/en-g2rl.pdf

Click the link to add information to this solution:
IS IT OK TO LEAVE THE VACUUM PRESSURE CONTROLLER PLUGGED IN ALL TIME WHEN PUMP SWITCHED OFF?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

The DRV8825 driver IC by TI (Texas Instruments) has two main connections called STEP and DIR. These are the two main connections that you need to use to connect to the Pokeys57CNC controller. You also need to connect the positive digital voltage pin (5V) from the Pokeys57CNC controller's motor connector to both the reset and sleep pins. The GND pin from the Pokeys57CNC motor connector is connected to the GND pin of the DRV8825 driver. The enable pin of the DRV88525 can remain unconnected.

There is a trimmer potentiometer on the DRV8825 that can increase or decrease the amperage setting for the motor. Depending on the DRV8825 board you purchased, there may be two pads to determine the amp setting while turning the trimmer (in the voltage setting on your multimeter).

The A1 and A2 is connected to one of the motor's coils and B1 and B2 is connected to the other motor's coil. There is a pin on the DRV8825 called VMOT that you will connect to the power supply (max 45VDC) and the GND pin next to the VMOT is the V- for the same power supply.

I hope this helps. If not, please add additional information on this thread.

Additional Information:
I followed (to the best of my ability) the instructions provided to my original question, but I did not receive successful results. When I followed the instructions and connected the ground pin from the Pokeys57CNC motor connector to the DRV8825 / A4988 expansion board, it stops the communication between the Pokeys57CNC board & the motors 1-3 that I had working previously. The DRV8825 / A4988 expansion board will be the fourth driver I am connecting to the Pokeys57CNC. The previous three drivers are PoStep-60's if that helps understand the issue.

Prior to hooking up the ground pin (I used pin 10 from the Pokeys57CNC motor connector) to the DRV8825 / A4988 expansion boards ground pin, I was able to see the power being applied via the red LED being illuminated on the DRV8825 board; after this new configuration the light is not turning on.

With the new recommended setup, I used a heat shrink solder piece to add the shunt for the connection to the sleep pin. The connection to the sleep pin is where I believe my issues are stemming from. I must be connecting it to the incorrect pin (within the 9 pin layout on the DRV8825 / A4988 expansion board). Do you have any reference to the 9 pin pinout on the A4988 expansion board? I double checked the pinout provided on the Texas Instruments page, but it only gives clarity to the pinouts on the DRV8825 board itself. After reviewing their documentation, I tried connecting the 5v (pin 9 from the Pokeys57CNC motor connection that's split to connect with the reset pin on the DRV8825 / A4988) wire directly to the terminal on the DRV8825 board and that didn't work either.

Any help or clarification you can provide would be greatly appreciated!

Click the link to add information to this solution:
How can I connect the Pokeys57CNC controller to a DRV8825 / A4988 expansion board?

You can use a Pickit 2 programming to load firmware onto the usb driver. The USB use a Microchip pic microcontroller. If you can manage writing a program for the Pic microcontroller and have a Pickit 2 firmware uploader (programmer), you should have no problem.

Click the link to add information to this solution:
Does the USB controller come with driver installation instructions so we could create our own user interface to communicate with the motor?

"Soft limits are used to decelerate machine to stop before machine is stopped hard way at limit switch or before it crashes. I recommend "Soft Limits Decelerate" and "Soft Limits Strict" settings are also checked. Sometimes we need to disable soft limits and there is a command for this in menu "Machine/Soft Limits". When soft limit is triggered position display will be yellow."

Are the soft limits "grayed out"?
Here is a link to a very useful forum post from the Planet-CNC crew:
http://www.planet-cnc.com/faq/machine_setup/



Additional Information:
i keep getting scratches when engraving pictures on dog tags

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

Yes, proximity sensors work similarly to limit switches. There are three connections that connect to the signal (input terminal) and two power connections that is connected to the 24V power supply that supplies the Mach3 USB controller. I have only tested NPN proximity switches with that controller in NO (normally open mode).

Click the link to add information to this solution:
Is it possible to add proximity sensors with your USB Controller Board

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

No, the red mach3 USB controller will only work with mach3, you will need the pokeys57cnc. This controller will work with mach3 or mach4.
Here is a link:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi, is it possible to operate red USB controller with Mach4? What plugins do I need? Thank you.

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

The BobCAD post processor that will work with the USB interface that uses the Planet-CNC software:

According to the Planet-cnc folks, wincnc or mach3 post-processors should work. According to a representative at BobCAD, mach3 post-processor should work.

Click the link to add information to this solution:
Do you know which BobCAD-CAM post processor works with your USB controller? Do you have a dll or command document to communicate with your USB controller?

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

Click the link to add information to this solution:
I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

Yes, this 4th axis system will work with the Masso controller. The 4th axis has a standard stepper motor. You will need a driver between the Masso controller and the stepper motor.

Click the link to add information to this solution:
[410] Will this work with the OneFinity Elite series with the MASSO controller?