[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14008

Question: I am looking for a lead screw with a 4mm lead, at least 4 starts and 36" in length, can you help me out?

Current Solution

I will check with some of our suppliers.

Respond:

Other Possible Solutions to this Question

  • Regarding 1/2" 5 start and 10 TPI ACME precision lead screw, what the maximum length you can ship within USA? I'm looking for something like 100" and I could use a 1" screw if available. Please include estimated price. Thanks.

    The maximum length we can ship is a total of 78" inches. However we can send your required length in portions. Please refer to adding the total items you require to your cart to get a visualized amount and shipping cost.

    Click the link to respond:
    Regarding 1/2" 5 start and 10 TPI ACME precision lead screw, what the maximum length you can ship within USA? I'm looking for something like 100" and I could use a 1" screw if available. Please include estimated price. Thanks.

  • I am building a cnc router with twin ball screws on the long axis and I will have a rotary axis as well. I need a 5 axis breaker board using only 4 axis total. Can you help me?

    Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

    Click the link to respond:
    I am building a cnc router with twin ball screws on the long axis and I will have a rotary axis as well. I need a 5 axis breaker board using only 4 axis total. Can you help me?

  • I am looking to build a cnc router that will cut 4x8 i wanted to get a cnc kit with some mods i was wondering if there was someone in sales that can help me

    Yes, if you give us a call, we can definitely help you. If you are looking to mod one of our 4'x8' machines, we can provide those changes for you. We have experience with meeting customers' needs where their application requires a machine with small or even large changes.

    Click the link to respond:
    I am looking to build a cnc router that will cut 4x8 i wanted to get a cnc kit with some mods i was wondering if there was someone in sales that can help me

  • how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question

    We currently only stock 2 start lead screw for the 3/8".

    Click the link to respond:
    how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question

  • how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question what is the minimum length and how much per inch
  • Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

    Ok, sure. Let's get the discussion started. Please respond with your questions on this FAQ

    Click the link to respond:
    Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

  • I am asking what to set my steps per using your kit stepper motors and a 1/2"x13 lead screw with Mach3

    Here is the formula for steps/inch (steps per inch)

    Steps = how many steps for a full ration of the motor = standard motor steps x number of microsteps for each step
    Standard motor steps for our stepping motors is 200 steps per revolution.
    Microsteps are selected on the driver and are shown as full, 1/2, 1/4, 1/8, 1/16, 1/32 etc... Use the denominator for the number of microsteps per step.

    Inches = how far the travel is for one full rotation of the motor. For the 1/2" - 13 TPI (threads per inch), the travel length will be 1"/13 or .076923". So, for one revolution of the motor, the travel distance will be .076923 inches.

    So, the steps = 200 * microsteps, let's make this 1/4 just for the formula.
    The inches will be .076923. Plug those into the formula:
    Steps / inch = (200 * 4) / .076923 This can also be written as:
    200 * 4 / (1 / 13) = 10,400

    Click the link to respond:
    I am asking what to set my steps per using your kit stepper motors and a 1/2"x13 lead screw with Mach3

  • where is the company store location i am in milton ont i am looking at shipping cost for the lead screws

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to respond:
    where is the company store location i am in milton ont i am looking at shipping cost for the lead screws

  • I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

    The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
    Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

    Click the link to respond:
    I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

  • Since I am using normal all-thread lead screw 13 TPI 1/2" for the book build cnc, what can be the maximum feed rate of machine and how can I change the mechanical setup in mach 3? I am using 1/4" steel carbile endmill with 2 flutes and router is 2 HP with variable speed

    Book build (scratch build), feedrates and recommendation.

    Using standard allthread will provide around 20-30 ipm using 36 volts. Although it allows for a working CNC machine, the RPM of the spindle/router will need to spin at the lowest setting to provide the beat efficiency and life for the end mill at 1/4" cut diameter and higher. The speeds may be fine for smaller end mills.

    If you would like faster speeds, you should change the lead screws on the CNC machine to the 1/2" 5 start 10 TPI which translates to 2 turns per inch which means, the stepping motor will not need to turn as fast to produce faster motion. That is to say, the stepping motor will only need to turn two revolutions for the machine to travel one inch and with the allthread, the stepping motor will need to turn 13 times to reach one inch.

    Link to the lead screw and other mechanical parts needed:
    https://www.buildyourcnc.com/CNCMachineMechanicalParts.aspx

    To change the lead screws you will need (for each axis):

    1. The lead screw for that axis.
    2. Two 1/2" collars to keep the lead screw axially stable.
    3. One Antibacklash nut.

    Additional Information:
    20

    Click the link to respond:
    Since I am using normal all-thread lead screw 13 TPI 1/2" for the book build cnc, what can be the maximum feed rate of machine and how can I change the mechanical setup in mach 3? I am using 1/4" steel carbile endmill with 2 flutes and router is 2 HP with variable speed

  • Looking to buy a black toe 2x4, what electronics are included ? Is it optional with USB-interface? And for last do you ship to sweden?
  • I need the calculation to determine the stepper motor torque to find the load that it can withstand in horizontal position using a lead screw at 1/2" diameter with 13 TPI.

    There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

    This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

    Effort = Sf + (Load/(2 x pi x (R/p) x Se))

    where:
    p = pitch of the screw
    Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
    Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
    Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
    R = radius of the lead screw


    This formula is based on the "law of the machine"

    The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

    Example:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 13 = .08 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
    Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
    Effort = 5 N + (90 N / (15.7))
    Effort = 5 N + (5.73 N)
    Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

    I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

    Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

    With a bit of algebra, the formula can be rewritten to find the load:

    Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

    Another formula that does not consider friction at all:

    Effort = (Load x p) / (2 x pi x R)

    Lets see if we get similar results:

    Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
    Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

    The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

    It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

    Example for a 10 TPI 5 start (2 turns per inch) lead screw:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 2 = .5 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
    Effort = 5 N + (90 N / (6.28 x 2 x .2))
    Effort = 5 N + (90 N / (2.512))
    Effort = 5 N + (35.83 N)
    Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

    Customer Response:
    thank you so much

    Additional Information:


    Additional Information:


    Additional Information:
    how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

    Additional Information:
    Pls


    Additional Information:
    1m 16mmdiameter ball screws calculations

    Click the link to respond:
    I need the calculation to determine the stepper motor torque to find the load that it can withstand in horizontal position using a lead screw at 1/2" diameter with 13 TPI.

  • I'm looking to upgrade my X-Carve with one of your vfd spindles, can you reccomend which one to use to replace the dewalt 611 router?

    If you would like to replace a router that outputs a relatively low HP (horse power) such as the Bosch PR20EVSK or Dewalt 611, both having about 1-1.25 HP, the 1.5kW spindle would have more than enough power and will also provide constant torque where the routers are unable to achieve. The 1.5kW spindle outputs 2 HP and is water cooled to keep the dust out of the air!

    Click the link to respond:
    I'm looking to upgrade my X-Carve with one of your vfd spindles, can you reccomend which one to use to replace the dewalt 611 router?

  • CAN YOU GIVE ME SOME HELP OR POINT IN THE RIGHT DIRECTION TO INCORPORATE MK 7 EXTRUDER WITH BOOK PLANS FOR 3D PRINTER?

    Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

    Click the link to respond:
    CAN YOU GIVE ME SOME HELP OR POINT IN THE RIGHT DIRECTION TO INCORPORATE MK 7 EXTRUDER WITH BOOK PLANS FOR 3D PRINTER?

  • I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

    It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
    If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

    Click the link to respond:
    I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

  • I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.
  • I couldn't find any information about how to mount the "z-axis lead screw in the book" (Build Your Own CNC)

    The details will differ depending on the type of lead screw you use.

    For allthread lead screws, you will need the 1/2" square nut, 1/2" allthread lead screw, two 1/4" screws and nuts to hold the square nut in place, two 1/2" ID bearings, two standard 1/2" nuts, and one coupling hub.

    Attach the square nut to the nut support using the two 1/4" screw and nuts. The bearings will need to be inserted into the seats of the lower and upper part of the z-axis. Insert the lead screw through the top bearing. Use one of the standard 1/2" nuts and start threading it on the allthread screw just below the bearing. Lower the lead screw to the square nut and start to screw the lead screw into the square nut. Continue until the screw is near the lower bearing. Add another standard 1/2" nut to the screw and keep turning the screw until the screw just passes the lower bearing. Add the coupling hub to the top of the screw just above the upper bearing. Turn the lower and upper standard 1/2" nuts until they are snug against the bearing. If the standard 1/2" nuts become loosened, consider adding another nut to each end against the existing nut to keep them in place.

    For 1/2" acme 5 start lead screws, you will need to use an antibacklash nut in place of the square nut. This nut attaches with a flange using two #8 screws and nuts. The standard 1/2" nuts are replaced by clamping collars.

    Click the link to respond:
    I couldn't find any information about how to mount the "z-axis lead screw in the book" (Build Your Own CNC)

  • I need the calculation to determine the stepper motor torque to find the load that it can lift using a lead screw at 1/2" diameter with 13 TPI.

    There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

    This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

    Effort = Sf + (Load/(2 x pi x (R/p) x Se))

    where:
    p = pitch of the screw
    Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
    Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
    Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
    R = radius of the lead screw


    This formula is based on the "law of the machine"

    The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

    Example:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 13 = .08 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
    Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
    Effort = 5 N + (90 N / (15.7))
    Effort = 5 N + (5.73 N)
    Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

    I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

    Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

    With a bit of algebra, the formula can be rewritten to find the load:

    Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

    Another formula that does not consider friction at all:

    Effort = (Load x p) / (2 x pi x R)

    Lets see if we get similar results:

    Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
    Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

    The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

    It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

    Example for a 10 TPI 5 start (2 turns per inch) lead screw:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 2 = .5 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
    Effort = 5 N + (90 N / (6.28 x 2 x .2))
    Effort = 5 N + (90 N / (2.512))
    Effort = 5 N + (35.83 N)
    Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

    Customer Response:
    thank you so much

    Additional Information:


    Additional Information:


    Additional Information:
    how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

    Additional Information:
    Pls


    Additional Information:
    1m 16mmdiameter ball screws calculations

    Click the link to respond:
    I need the calculation to determine the stepper motor torque to find the load that it can lift using a lead screw at 1/2" diameter with 13 TPI.

  • I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?

    Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

    Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

    Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
    Email(customerservice@buildyourcnc.com for further help)

    Click the link to respond:
    I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?