[ Log In ]
[ Register ]

Question #: 14055

Question: you didn't answer the question, also I ordered a usb breakout board

Current Solution

Yes, we see the order of the USB breakout board in our system to be shipped. The order is in the shipping process. The shipping label has not been created yet, but will be by the end of day.

Respond:

Other Possible Solutions to this Question

  • [65] So do you need a 24 volt power supply on the USB breakout board or can you use the 5 volt side ?

    To use the inputs and outputs on the MAch3 USB controller, you will need at least a 12 VDC power supply inte 24V terminal (V+) and the DCM terminal (V-). The common lead of the limit switch will be connected to DCM (V-) and the NO (Normally Open ) lead of the limit switch will be connected to the Input of your choice (IN1 - IN4).

    Click the link to add information to this solution:
    [65] So do you need a 24 volt power supply on the USB breakout board or can you use the 5 volt side ?

  • What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

    Any of the following power supplies will be fine for powering the Mach3 USB controller:
    https://www.buildyourcnc.com/item/24v

    however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
    https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

    Click the link to add information to this solution:
    What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

  • Do you have a wiring diagram for your breakout board and the SuperPID?

    It is not necessary for a wiring diagram for the breakout board to the SuperPID controller since you are only going to connect two wires from the breakout board output terminals of your choosing to the SuperPID controller. The only thing remaining is to configure Mach3 so that the spindle control section serves as the SuperPID controller.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to add information to this solution:
    Do you have a wiring diagram for your breakout board and the SuperPID?

  • Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

    I don't see why Mach3 under windows 64-bit wouldn't work with an interface that uses USB as it's primary communication method. I am a bit vague on this, so I will do more research on it.

    We recommend Mach3 run under Windows 32-bit when using the parallel interface as this is a legacy function.

    Additional Information:


    Additional Information:
    mach 3 usb board setup

    Additional Information:
    I am running Mach3 under Windows 7 Pro 64bit without any problems.

    Additional Information:


    Additional Information:


    Additional Information:
    Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

    Additional Information:
    Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

    Additional Information:
    Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

    Additional Information:
    Are you also able to use the parallel port as your controller on the WINDOWS 7 64bit OS?

    Click the link to add information to this solution:
    Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

  • can I use the usb on the parallel breakout board with planet cmc

    The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
    Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

    To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

    Click the link to add information to this solution:
    can I use the usb on the parallel breakout board with planet cmc

  • I just ordered a Pokey57 board. Do you have the pendant and lcd for this?

    We have the LCD but we don't have the pendant just yet.
    https://www.newbiehack.com/categories/newbiehack-LCD_Displays_and_LEDs-LCD-20x4

    The "newbiehack" website is a website owned by us and is under the PHD Robotics, LLC. Company.

    Click the link to add information to this solution:
    I just ordered a Pokey57 board. Do you have the pendant and lcd for this?

  • WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

    The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

    The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

    Click the link to add information to this solution:
    WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

  • Do you sell a USB driven breakout board for Mach4?

    Our USB CNC machine controller board works with Mach3. We haven't tried, or tested the USB board on Mach4.

    Click the link to add information to this solution:
    Do you sell a USB driven breakout board for Mach4?

  • WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

  • What is the usb port for on the 5 Axis Breakout Board with Relay ($28.50)?

    The USB port located on the parallel 5 axis breakout board is for powering the board. There is no communications related to this port.

    Click the link to add information to this solution:
    What is the usb port for on the 5 Axis Breakout Board with Relay ($28.50)?

  • I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

    For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

  • I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.
  • Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

    The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

    Click the link to add information to this solution:
    Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to add information to this solution:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • Will the USB breakout board work with Mach3?

    Our newer USB board will work with Mach3 and can be found here at this URL:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Additional Information:
    Mach3 breakout board including software

    Click the link to add information to this solution:
    Will the USB breakout board work with Mach3?

  • Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

    These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

    Click the link to add information to this solution:
    Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

  • Will the USB breakout board control 4 axis?

    The USB breakout board can control up to a 4th axis.

    Click the link to add information to this solution:
    Will the USB breakout board control 4 axis?

  • Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

    The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

    First, go to this link and look at the chip diagram:
    https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

    Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Click the link to add information to this solution:
    Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

  • I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

    No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

    I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

    If you have difficulty finding the answer, here is a link:
    https://www.buildyourcnc.com/FAQ/13636

    Click the link to add information to this solution:
    I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.