It is not necessary for a wiring diagram for the breakout board to the SuperPID controller since you are only going to connect two wires from the breakout board output terminals of your choosing to the SuperPID controller. The only thing remaining is to configure Mach3 so that the spindle control section serves as the SuperPID controller.

To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

Click the link to add information to this solution:
Do you have a wiring diagram for your breakout board and the SuperPID?

We will provide shim washers as a part of machine assemblies, but when purchasing lead screw and bearings, the shim washers must be purchased as well. Please give us a call and we can send them out.

Click the link to add information to this solution:
I just ordered a 1/2" lead screw and bearings, etc. But I don't see any 1/2" shim washers for those bearings. If you have any, please toss 8 of them in the shipment and I'll gladly reimburse you.

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

I recommend using a wireless pendant rather than one that is wired to the controller.

Here is a link to one on Amazon.com: https://amzn.to/3r3AfTm

This is an affiliate link.

Click the link to add information to this solution:
[596] I am new to CNCs, curious to know what I need to look for in a pendant that would be compatible with this board and Mach4?

Yes, we see the order of the USB breakout board in our system to be shipped. The order is in the shipping process. The shipping label has not been created yet, but will be by the end of day.

Click the link to add information to this solution:
you didn't answer the question, also I ordered a usb breakout board

The most likely issue here is that your email did not save in our system. Please email us to determine your shipping status and tracking number at customerservice@buildyourcnc.com

Click the link to add information to this solution:
I ordered the Mach 3 usb controller board on the 1st and I have not received an order conformation or shipping confirmation. My account was charged however.

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
do you have CAD available for the hiwin guide blocks you sell and the rail?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

I just looked at your account and noticed that your shipments has not been made yet. I will talk to the shipper tomorrow morning when the office opens determine what happened. My apologies for this.

Click the link to add information to this solution:
I ordered a 1.5kW Spindle and Inverter (110 Volt) on December 18th and have heard nothing since. I notice you did charge my credit card for the purchase. Please update me with an ETA as soon as possible.

I do not recommend using the Mach3 USB controller to be used with a torch height controller. There are only 4 inputs on the Mach3 USB controller. We have tried to interface a Proma THC to this board without success; however, we did not exhaust all possibilities.

I would recommend the Pokeys57CNC controller to connect the Proma THC as I have interfaced these two before and they work well together.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Hello. Does this USB interface board thc? I have the proma 150.

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?

The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

Click the link to add information to this solution:
I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

We can special order this part for you. Give us a call and we will either find the part for you, or find a part that we can machine to your specifications.

Click the link to add information to this solution:
HI, I am looking for a drive sproket for a roller chain. The drive sproket should have an ID= 16mm. do you have something like this in your inventory?

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.