To use the PoKeys57CNC with KUKA, you will need to make sure that the servo drives will be able to receive pulses that are generated from their 8 step/dir signals.

The PoKeys57CNC Manual states:

PoKeys57CNC is a blend between general purpose PoKeys device and motor controller. The device is targeted primarily for controlling up to 8 STEP/DIR signal driven motors (stepper motors, servo drives, etc.)

Here is a link to the Pokeys57CNC Manual:
https://www.poscope.com/wp-content/uploads/downloads/Pokeys/Manuals/PoKeys57CNC%20user%20manual%20(23.3.2017).pdf

Click the link to add information to this solution:
Does the PoKeys57CNC board with MACH4 support simultaneous coordinated motion, as in controlling a 6 axis robot arm with large servo motors? I have 4 huge KUKA robots with complete control cabinets with all the servo drivers intact but the control language is so old and obsolete that it makes them pretty useless.

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

Hi. The HIWIN spec rail will fit standard M5 screws. If you are using non standard screws with wide heads, or pan heads that are a bit larger than a standard round heads, then it may not fit. Make sure to source screws that have standard round heads, or socket heads for fastening the 20mm HIWIN spec rails.

Click the link to add information to this solution:
I purchased some of your 20mm Hiwin Linear Rails. M5 bolts do not fit flush. The head stands out. Is the spec sheet out of date? What bolts will fit this rail AND T Nuts compatible with 8020's 15 series extrusions? Thanks.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Is this a licensed version of Mach 3? If not and you are currently running the demo version, mach 3 will have only 500 lines of G-code available for cutting. Which will not allow you to cut or move the machine after the first 500 lines.

Additional Information:
Yes, It is a licensed version of Mach 3.

Click the link to add information to this solution:
Mach 3 stalls in the middle of a file and the dwell button is flashes randomly. Can't control motors and have to re-start Mach 3. Any help?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

The steps per unit is automatically determined in the calibration of the axis by clicking on the "set steps per unit" button above the reset button on the settings tab. Initially set the velocity and acceleration to a low setting, like 100 and 10 respectively, so that the axis does not stall during this operation. Once calibrated, the steps per unit will be set to the correct value and the velocity and acceleration can be increased. I have a video explaning the tuning of the motors on this page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The name of the video is Test and Tune the motors.

Click the link to add information to this solution:
I purchased the large gantry system with USB control. I have built the CNC and it is working fine. Now fine tuning the motors. On the X-axis I have the Velocity set at 60 (inches), Acceleration at 1.4, the Step Pulse 1-5us and Dir Pulse set at 0. Do I need to adjust the pulses?

Yes, PoKeys57CNC does support auto gantry squaring if both master and slave axes are equipped with home switches independently.

Click the link to add information to this solution:
Does the Pokeys57CNC controller support Auto-Squaring in Mach 4?

Yes, PoKeys57CNC does support auto gantry squaring if both master and slave axes are equipped with home switches independently.

Click the link to add information to this solution:
Does the Pokeys57CNC controller support Auto-Squaring in Mach 4?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

CAD drawings are not furnished with the purchase of a machine.

Click the link to add information to this solution:
I have a greenbull 5x Long Z. I thought I read that I would get the CAD files to the machine when I purchased it? I want to make a couple modifications. Thanks!