[ Log In ]
[ Register ]

Question #: 14858

Question: [4th Axis with Tail Stock] will this 4th axis work on laguna 1q cnc

Current Solution

The Laguna 1Q has 154 mm of gantry clearance which is enough to clear the 100mm chuck and base of the 4th axis.

Respond:

Other Possible Solutions to this Question

  • will mach4 software work with planet CNC breakoutboard?

    Our USB breakout board, will not work with Mach 4! The USB BoB is specifically designed to work with Planet-CNC.

    Click the link to add information to this solution:
    will mach4 software work with planet CNC breakoutboard?

  • I am looking at your 3 axis CNC machine kit(part #101) on Amazon. Is the interface on this kit USB?

    The electronics combo with the sku of 101 on Amazon.com includes a parallel interface.

    Click the link to add information to this solution:
    I am looking at your 3 axis CNC machine kit(part #101) on Amazon. Is the interface on this kit USB?

  • WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

    no, it will only work on anodized aluminum

    Click the link to add information to this solution:
    WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

  • I build a 3 axis router CNC the gantry is heavy in aluminium plate, witch plug n'play kit you suggest me 1 or two motor on the longest axis this will be drive with chain?

    What is the weight of the gantry, number of teeth on the drive sprocket and tooth pitch?

    Click the link to add information to this solution:
    I build a 3 axis router CNC the gantry is heavy in aluminium plate, witch plug n'play kit you suggest me 1 or two motor on the longest axis this will be drive with chain?

  • I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

    If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

    Click the link to add information to this solution:
    I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to add information to this solution:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • What size motor is powering the y axis on the greenLean CNC machine?

    For our greenLean CNC vertical machine, was built and controlled using 2 651-oz in motors/425 oz-in motor.
    The 651-oz motors runs both the x/y axis, as our 425-oz motor controls the z axis.

    Click the link to add information to this solution:
    What size motor is powering the y axis on the greenLean CNC machine?

  • Can I use your USB interface board and Mach4 on my 3 axis CNC router?

    The USB interface that we sell only works with planet-cnc software. We will be developing our own USB board and plug-in that will work with Mach4 very soon.

    Additional Information:
    does the mach3 usb interface board work with mach4?

    Click the link to add information to this solution:
    Can I use your USB interface board and Mach4 on my 3 axis CNC router?

  • Can I use your USB interface board and Mach3 on my 3 axis CNC router?

    Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

    Click the link to add information to this solution:
    Can I use your USB interface board and Mach3 on my 3 axis CNC router?

  • WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

    3 axis machines cannot create undercuts in the part.

    These videos show the capabilities of 3 and 5 axis machining:

    3-axis CNC:

    &feature=fvwrel

    5-axis CNC:
    &feature=related

    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

  • MY AXIS ONLY MOVES ONE STEP AT A TIME IN LINUX CNC EMC2

    Flip the values under "table travel" within "stepconf wizard". For example: if the table travel numbers are "4 to -10", switch them to "-4 to 10".

    Click the link to add information to this solution:
    MY AXIS ONLY MOVES ONE STEP AT A TIME IN LINUX CNC EMC2

  • Will Planet CNC software run nc files created in CamBam?

    Planet-CNC's software is tested functional with CAMBAM according to their website, so this should be possible.

    Click the link to add information to this solution:
    Will Planet CNC software run nc files created in CamBam?

  • I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?
  • HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

    The motor that is attached to the 4th axis is wired as follows:

    The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

    Click the link to add information to this solution:
    HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

  • HOW DO CNC MACHINES WORK?

    A CNC machine takes codes from a computer and converts the code using software into electrical signals. The signals from the computer are then used to control motors. Since the motors can turn very small amounts the machine is able to move in highly precise movements over and over again.

    Click the link to add information to this solution:
    HOW DO CNC MACHINES WORK?

  • Can any of your CNC kits be adapted to work with a manual wood lathe?

    It's best to design a machine specifically for a lathe rather than adapting an existing machine kit to an existing lathe. If you are interested in us designing a machine like this, let us know.

    Click the link to add information to this solution:
    Can any of your CNC kits be adapted to work with a manual wood lathe?

  • Is the USB hub ready for use with Mach3 at this time, or just Planet CNC?
  • DOES THE SOFTWARE WORK ON AN APPLE?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Click the link to add information to this solution:
    DOES THE SOFTWARE WORK ON AN APPLE?

  • I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?
Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.