The settings that will have to be change will be your steps per inch in motor tuning (mach 3), or settings/axes(planetCNC). But we do not have the actual numbers/specs that will fit your 10 TPI 5 start lead screw, here is a tutorial video which explains how to get the exact numbers you need! (

Click the link to add information to this solution:
On the book build machine I changed the Z axis from a 13 tpi lead screw to an acme 10 tpi 5 start lead screw. What numbers do I put into the motor tuneing boxes.

Yes, you can use 12VDC for the MAch3 USB controller at the 24V and DCM terminals. I have not tested using 12VDC in conjunction with the ACM and AVI terminals (PWM output) to control the spindle speed. PWM typically requires a reference voltage (from the VFD) and it's own voltage to produce the PWM signal. I am not sure if 12VDC is sufficient for the PWM. I have tested the inputs with 12VDC and they work fine.

Click the link to add information to this solution:
[575] does the 24VDC input actually need 24 VDC if only using the input for homing switches? Can you use 12 VDC? and would it be damaged with a higher voltage than 24 VDC?

In regards to getting a complete plug and go system, there are a lot of items to consider.
Electronics, DYI or one of our electronics kits that come assembled and tested?
Cable for the motors is a additional purchase, spindle? = silicone tubing/water pump, etc.
Cable carrier (wire management), software (also additional purchase).

We can view your cart, but please send us your email and username to customerservice@buildyourcnc.com so it will remain secure!

Click the link to add information to this solution:
I want to by a 5 by 10 foot kit, sorry, I don't have the time to read everything here. what should I be thinking about, Can you veiw my cart and tell me what else I need to get?

Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

Additional Information:
Rnrmotion.dll is a dynamic link library which is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still run run windows defender against it to make sure.

Additional Information:

Click the link to add information to this solution:
I intend to intall mach3 on Windows 10 OS. Will I need to install the USB Motion Driver RnRMotion.dll? I attempted to download this but it was blocked by Windows 10.

Yes. We will make sure the lead screw is cut to those dimensions. 53/30/13

Click the link to add information to this solution:
I ordered 96 inches of the 1/2 inch 10 tpi drive screw. I need it in 3 pieces. 53 inches, 30 inches, and 13 inches. Please let me know if that can happen. Thankyou

I am getting the solution from the developer. I will put the solution on this page when they provide the solution.

Thanks, Patrick

Additional Information:
Here is the information I received from the developer:

These are available on Windows 10. PoBlocks does not require .NET, but the communication library that the PoKeys app uses does need it.

Go to the control panel -> Search for "Turn Windows features on or off" -> Make sure the checkbox on the line ".NET Framework 3.5 (includes .NET 2.0 and 3.0)" is checked (or filled in).

Click the link to add information to this solution:
[596] I am trying to install the Pokeys configuration and Poblocks on a windows 10 computer. An error message says Ineed net frameworks 2.5 qnd 3.0.Both appear to be unavalable.Solution?

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

The plans for the whiteAnt 3D Printer will have the dimesions, and the dimensions will be on the individual pieces(cut to spec). The machine is relatively small, so maybe you expected the size(dimensions) to be larger.

Click the link to add information to this solution:
The plans available for download for the "whiteAnt 3D Plastic Printer" do not have dimensions. Are the dimensions shown in the book? Is there a DWG file available?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
Purchasing and shipping a kit internationally would make the price prohibitive. Are the dxf files available on their own so that the parts can be machined locally?

That video was hosted by Metacafe and I just went to the permalink for the video, but no video. Metacafe failed me on this one. I will look for my raw video (which will take a bit of time) and re-post it to youtube.

If there are specific questions; please post them here and I will help you along the way. As these questions are asked and answered, they help others as well in the future.

Click the link to add information to this solution:
"Step 34 - Software Toolchain Part 1 - Mach 3 Installation" Video is missing. Do you have? Am trying to install Mach3, need someone to hold my hand a bit here :-)

That product page for the mini breadboards can be found on our sister site: newbiehack.com. Here is the link: https://www.newbiehack.com/categories/newbiehack-prototyping-breadboard-mini-breadboard-17x100-blue

Additional Information:
I'm curious, how did you get to the buildyourcnc.com site for that product? Was it a google search. I would like to know so I can modify the description so the product can be found more successfully. Thanks.

Additional Information:
Was looking for answers on how to invert signals for opposing steppers Seen your solutions bought the hex inverter and breakout board from newbiehack

Click the link to add information to this solution:
Mini Breadboard 17x10 with a self adhesive on the back. Blue color. Measures 1.365 inches x 1.8 inches with a thickness of .375 inches. Don't see the page to order.

To connect the stepper motor drivers to the Mach3 USB interface card, you will need to follow the wiring diagram here: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
which can be found here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board along with all of the other manuals associated with that interface card.

Please note that the DC+ and DC- on that wiring diagram (power supply to thye stepper motor drivers) is not correct. The DC- is connected to GND on the drivers and the DC+ is connected to VCC on the drivers. Typically, the DC+ on the power supply is labeled V+ and the DC- is labeled either COM or V-.

If you are having any issues with the wiring, please let me know and I will elaborate. Thanks.

Click the link to add information to this solution:
Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

Assumption 1: The "raw data" of 24 mrem on the TLD is the total dose received by the TLD during the 22 days that the TLD was deployed in your office. This means that (1) any TLD reader background signal has been properly subtracted, (2) the signal accumulating in the TLD during any transport or storage time between preparation (annealing) and deployment in your office has been properly subtracted and, (3) the signal accumulating in the TLD during any transport or storage time between removal from your office and processing (reading) has been properly subtracted.

With this assumption, the total dose rate in your office is (24 mrem)/(22 days), or 1.091 mrem per day. The reference background is given as 63 mrem per year which is (63 days)/(365.25 days per year) or 0.172 mrem per day. Thus the average net dose rate to the TLD during the 22 days was (1.091-0.172) = 0.919 mrem per day.

Assumption 2: The net dose rate of 0.919 mrem per day in your office is attributable to the accelerator or other regulated sources under the control of your institution.

Assumption 3: The office occupancy factor of 1/4 attributed in your question to NCRP Report 49 was misread from Table 4. The correct occupancy factor given in NCRP 49 for offices is 1.

Assumption 4: You take 20 business days per year off for vacation and holidays. You work in your office for the remaining 240 days per year.

Assumption 5: All of the accelerator shots occur while you are in your office.

Assumption 6: The average net dose rate of 0.919 mrem per day determined during the 22 days of measurement continues for a year.

Based on the data that you provided and my assumptions, your annual dose received in your office from the accelerator or other regulated sources at your institution is predicted to be (0.919 mrem per day) x (240 work days per year) = 220 mrem.

Tom Gesell, PhD

Click the link to add information to this solution:
HOW CAN I DETERMINE THE DOSE EQUIVALENT (MREM/HR, MREM/WK, MREM/YR) USING RAW DATA FROM A TLD (THERMOLUMINESCENT DOSIMETER) THAT WAS PLACED IN AN OFFICE FOR 22 DAYS?

http://hps.org/publicinformation/ate/q5906.pdf

Click the link to add information to this solution:
HOW DO YOU CALCULATE THE ENERGY OF PHOTONEUTRONS PRODUCED THROUGH INTERACTION WITH 7.5 MEV BREMSSTRAHLUNG FROM A LINAC? TARGET GENERAL COMMERCIAL PRODUCTS IN TRUCKS.

CAD drawings are not furnished with the purchase of a machine.

Click the link to add information to this solution:
I have a greenbull 5x Long Z. I thought I read that I would get the CAD files to the machine when I purchased it? I want to make a couple modifications. Thanks!

To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

Click the link to add information to this solution:
i have a breakout usb controller iam using a spindle output to active a relay 5V but it didnt work.... whats the problem, what else i need to active that realy 5v 10A?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I have a 2000 WK 11–3 Z limit switches going to A c10r10 breakout board . Can I also use them as my home position as well. I need The wiring configuration

The NEMA 11 16.7 oz-in motor is a dual shaft motor and the rear shaft extend 15mm or .59 inches.

I've added an image to the product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-nema11-16!7ozin-NEWBIEHACK-motors-stepping_motor-16!7_ozin

Click the link to add information to this solution:
Is the NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps actually a dual shaft stepper motor? The drawings only show the shaft coming out one side.

Prior to the 2010-11 vaccination season, only children ages 6 months through 18 years and adults age 50 years and older were universally recommended for vaccination; recommendations for adults ages 19 through 49 years were targeted to people with specific risk factors, although other adults could be vaccinated if they wanted protection. Collectively, these targeted risk groups made up 85% of the U.S. population. During the 2009 H1N1 outbreak, additional risk groups were identified, such as obese individuals. The recommendation made by ACIP in February 2010 for universal vaccination simplifies previous recommendations, making it easier for healthcare providers to determine whom to vaccinate. The universal recommendation also makes it easier for patients to remember to get vaccinated every year.

Click the link to add information to this solution:
WE'RE GLAD THAT CDC HAS MADE A UNIVERSAL INFLUENZA VACCINATION RECOMMENDATION TO VACCINATE EVERYONE 6 MONTHS AND OLDER. WOULD YOU TELL US HOW THIS CAME ABOUT?