Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

There are two main alternatives if you want to use the mach3 software:
First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

Additional Information:


Additional Information:


Additional Information:
The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

Click the link to add information to this solution:
I have a planetcnc USB controller to run my project and when I start the 240v router the USB connection shuts down.

The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

There are two main alternatives if you want to use the mach3 software:
First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

Additional Information:


Additional Information:


Additional Information:
The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

Click the link to add information to this solution:
I have a planetcnc USB controller to run my project and when I start the 240v router the USB connection shuts down.

The Planet CNC Software will require purchase after the trial version is completed, and will be purchased through their website. Currently that is the only software available for the USB Controller.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Must I have licence to run planetpc software, is there any other software that will run the usb controller

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?

To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
Since the machine is metal, our larger motors would be highly recommended.

We have not done this conversion, through research is recommended.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

There are two main alternatives if you want to use the mach3 software:
First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

Additional Information:


Additional Information:


Additional Information:
The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

Click the link to add information to this solution:
I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

Drivers will have terminals with labels that represent a pulse, clock or step, and for direction. Look at the following to determine which terminal is used for what purpose.

Step- = CP- = P-
Step+ = CP+ = P+
Dir - = CW- = D-
Dir+ = CW+ = D+

Click the link to add information to this solution:
Hi, I have one of your mach3 controller boards and have followed the tutorial videos but my motor drivers do not have p+ p- d+ d- I only have sted, dir, en and +5v

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

Planet CNC has the option to turn off these outputs on your USB board. Under the File/settings/Pins. You will have Spindle (M3,M4,M5) Coolant (M7,M8,M9) as available output pins. On the drop down tabs for these output pins you will have this option ( --- ), if selected it will turn of that output pin in your board and you will get not voltage change in the pin.

Additional Information:
Cannot activate output in mkx

Click the link to add information to this solution:
On the USB controller I am unable to get voltage from the Mist relay block on the board. The Flood and Spindle produce a voltage change correctly. Is there a setting I am missing?

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

Please provide more information about how you have the limits and home switches connected to the controller. Depending on the configuration of your machine, you may not need anything on input number 3.

Click the link to add information to this solution:
Hi, What wire goes to input 3 for home limit and do I have to change anything in Mach3??

No, the 3.1 version will not support slaving the X axis. You will either need to wire the two x axis driver to the same X signal pins, or use the DDCS v4.1 which does support slaving an axis.

Click the link to add information to this solution:
[823] I plan to use a DDCS stand alone controller for a CNC router build which will have two stepper motors on the x axis, one on Y and one on Z. Will the 3.1 version handle two motors synched on the X axis or will I need the 4.1 version?

The most likely issue here is that your email did not save in our system. Please email us to determine your shipping status and tracking number at customerservice@buildyourcnc.com

Click the link to add information to this solution:
I ordered the Mach 3 usb controller board on the 1st and I have not received an order conformation or shipping confirmation. My account was charged however.

If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

Click the link to add information to this solution:
How should I connect the limit switches to my laser controller?

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Y axis on usb controller not working. The motor gets power and holds but will not turn. I tried switching the same wires, driver, and motor over to the A axis on the controller and it works fine like that. I have double, and triple checked the wiring

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia