Apologies for the delay in response during the holiday season. Please let us know if this item has not been delivered by calling us at the number at the top right of the website.

Click the link to add information to this solution:
I just made an order for Vacuum Pump Controller Pressure Sensor Switch. When can I expect the delivery?

All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

Click the link to add information to this solution:
How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

The 12VDC applied to the input voltage terminals most likely damaged the microcontroller, the LCD, and the vacuum sensor. It can be repaired, but the repair will cost more than a new vacuum pressure controller.

Click the link to add information to this solution:
[244] I accidentally put 12vdc to the controller and now the display does not work. Can this be repaired?

I don't see anything in the datasheet for the relay that indicates an overheat condition. While the relay is engaged, the power consumption is 400 mW and I don't believe this is enough to raise the temperature faster than the heat dissipation from the metal on the leads through convection or radiation outside of the rated temperature working ranges providing that you maintain an ambient temperature range within -40°C to 85°C (with no icing or condensation).

http://www.omron.com/ecb/products/pdf/en-g2rl.pdf

Click the link to add information to this solution:
IS IT OK TO LEAVE THE VACUUM PRESSURE CONTROLLER PLUGGED IN ALL TIME WHEN PUMP SWITCHED OFF?

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

To use a touch plate on any controller, all you need is a conductive flat material with a known thickness and some wire and alligator clips. Solder a wire to the touch plate and connect the other end of the wire to the free input terminal of the controller. Connect a wire with an alligator clip to the ground of the controller (on the Mach3 USB controller, this ground is the DCM terminal, or the digital gnd on the 24VDC power supply). Connect the alligator clip to the end mill.

You can either use a script to serve as the probe, or you can use the ref all home button and setup the touch plate as a home switch.

Additional Information:
I connect wire to cmd- and to in2. I cant getbit to work, what arecthe corresponding ports and pins to usenin mach3? Please help.

Click the link to add information to this solution:
Hello, Can I hook up a Z axis touch plate to the usb controller?

You can find all of the wiring instructions for the Mach3 USB controller here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down until you see the videos. The wiring instructions cover wiring all of the axes, setting up the inputs to sense limit switches, setting up the outputs and how to diagnose the outputs, setting up an external relay to control external devices, and setting up spindle speed.

Click the link to add information to this solution:
where can I find wiring instructions for the Mach3 USB controller?

Yes, you can add a relay to the Mach3 USB controller. The relay must be a 24V relay on it's input side and be able to be set to active low. I demonstrate this in a video on the following page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The video is titled: Mach3 USB Controller Outputs

Click the link to add information to this solution:
Can I add a relay to the Mach3 USB controller?

Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
Slave 1 - X-Axis
Slave 2 - Y-Axis
Slave 3 - A-Axis
Slave 4 - B-Axis
Etc...




Additional Information:
Do you act as if it's one motor and it goes to one controller on the motherboard?

Click the link to add information to this solution:
Can I run two stepper motors off the same axis output on the USB controller?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
How can I connect an inductive proximity sensor to the Mach3 USB controller?

The DRV8825 driver IC by TI (Texas Instruments) has two main connections called STEP and DIR. These are the two main connections that you need to use to connect to the Pokeys57CNC controller. You also need to connect the positive digital voltage pin (5V) from the Pokeys57CNC controller's motor connector to both the reset and sleep pins. The GND pin from the Pokeys57CNC motor connector is connected to the GND pin of the DRV8825 driver. The enable pin of the DRV88525 can remain unconnected.

There is a trimmer potentiometer on the DRV8825 that can increase or decrease the amperage setting for the motor. Depending on the DRV8825 board you purchased, there may be two pads to determine the amp setting while turning the trimmer (in the voltage setting on your multimeter).

The A1 and A2 is connected to one of the motor's coils and B1 and B2 is connected to the other motor's coil. There is a pin on the DRV8825 called VMOT that you will connect to the power supply (max 45VDC) and the GND pin next to the VMOT is the V- for the same power supply.

I hope this helps. If not, please add additional information on this thread.

Additional Information:
I followed (to the best of my ability) the instructions provided to my original question, but I did not receive successful results. When I followed the instructions and connected the ground pin from the Pokeys57CNC motor connector to the DRV8825 / A4988 expansion board, it stops the communication between the Pokeys57CNC board & the motors 1-3 that I had working previously. The DRV8825 / A4988 expansion board will be the fourth driver I am connecting to the Pokeys57CNC. The previous three drivers are PoStep-60's if that helps understand the issue.

Prior to hooking up the ground pin (I used pin 10 from the Pokeys57CNC motor connector) to the DRV8825 / A4988 expansion boards ground pin, I was able to see the power being applied via the red LED being illuminated on the DRV8825 board; after this new configuration the light is not turning on.

With the new recommended setup, I used a heat shrink solder piece to add the shunt for the connection to the sleep pin. The connection to the sleep pin is where I believe my issues are stemming from. I must be connecting it to the incorrect pin (within the 9 pin layout on the DRV8825 / A4988 expansion board). Do you have any reference to the 9 pin pinout on the A4988 expansion board? I double checked the pinout provided on the Texas Instruments page, but it only gives clarity to the pinouts on the DRV8825 board itself. After reviewing their documentation, I tried connecting the 5v (pin 9 from the Pokeys57CNC motor connection that's split to connect with the reset pin on the DRV8825 / A4988) wire directly to the terminal on the DRV8825 board and that didn't work either.

Any help or clarification you can provide would be greatly appreciated!

Click the link to add information to this solution:
How can I connect the Pokeys57CNC controller to a DRV8825 / A4988 expansion board?

If you are getting the "Communicating Unsuccessful!" error when you are trying to communicate between LaserCAD and the AWC608 Laser Cutter and Engraver controller (after you have already tried installing the USB driver from the LaserCAD setup procedure), these are the steps you will need for a successful communication:

- Open the Device Manager window (right click on the start menu and select Device Manager)
- When you plug the USB cable from the AWC608 Laser Cutter Controller (USB Type B connector) to the computer, you should see a new item in the Device Manager, possibly under "Ports (COM & LPT)", or under "Other Devices". It may show as an item under "Other Devices", possibly FT245R and has an "!" in a yellow triangle.
- Download the latest FTDI drivers from: http://www.ftdichip.com/Drivers/D2XX.htm
- Unzip the files to a folder that can be easily browsed.
- Right click on the item that appeared in the Device Manager when the cable was plugged in between the Laser Cutter AWC608 controller and the computer.
- Click on update driver
- Select the procedure to manually install the driver and browse to the folder containing the FTDI driver and follow the step in the driver installation wizard.
- The item should now be located under the "Ports (COM & LPT)" and should be named "USB Serial Device (COM#)". The # will be the number you will use in the LaserCAD software.
- In the LaserCAD software, click the "Select Mode" at the far top right of the Laser CAD user interface.
- Make sure USB mode is selected.
- If the Machine name with the correct COM number is listed, select it and exit the dialog window. Otherwise, click on "Add" and fill in the details with the new COM number.

Additional Information:


Additional Information:
Communicating unsuccessful

Additional Information:
Communicating unsuccessful

Click the link to add information to this solution:
I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

Yes, you can use the 4 axis kit and use two of the motors on the gantry. You will need to wire the gantry axis motors to the same step and direction signals on the controller interface. For example, if the gantry axis is the X axis, then on the controller step and direction terminals (CP and CW) is wired to both of the stepper motor drivers for the X axis.

Click the link to add information to this solution:
4 axis kit can I use 2 motors for the gantry with one controller card? or I buy the 3 axis kit instead?

In generally, you would only need a driver to drive the motor on the 4th axis.

A fourth (4th) axis can be added using a head stock that contains a motor where the motor turns a chuck that holds the object. The motor requires a driver that is controlled by an interface card such as the parallel breakout board, or the usb controller board. Our 4th Axis head stock can be driven by our standard 3.0 amp driver.

The software used to control the 4th axis would need to be able to control 4 axes (X, Y, Z and A). Mach3, LinuzCNC and Planet-CNC are good examples of control software that can control more than 3 axes.

Click the link to add information to this solution:
Can I add a fourth axis by just adding another controller?

If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

Click the link to add information to this solution:
How should I connect the limit switches to my laser controller?

I created a video to demonstrate how to use the outputs on the Mach3 USB controller. You can find this video on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down to the 5th video on that page. The title of the video is: Mach3 USB Controller Outputs

Click the link to add information to this solution:
How do I use the outputs on the Mach3 USB controller?

The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

Click the link to add information to this solution:
Is there a kit or actual product that can be wired into the Mach3 controller to give me virtual zero

The USB controller board is currently only compatible with Planet-CNC software.

Click the link to add information to this solution:
Can I use Mach3 or 4 with your USB controller PCA?