You will not be able to use a router mount for a spindle. You will need to get a spindle mount for your Z axis.

Click the link to add information to this solution:
I currently own a blacktoe router cnc.Want to convert to spindle.Do I use the same Z axis mount?

If you would like to use a spindle rather than a router on your existing CNC, we will send you another set of components that will allow the spindle to be mounted properly which includes the z-axis rails, rail support, spindle mounts and the dust shoe components. You can find this item to purchase here: https://www.buildyourcnc.com/category/z-axis

Click the link to add information to this solution:
I have blacktoe 4.1 with porter cable 890 router.To convert to spindle(2.2kw) can I just change the mount?

If you would like to use a spindle rather than a router on your existing CNC, we will send you another set of components that will allow the spindle to be mounted properly which includes the z-axis rails, rail support, spindle mounts and the dust shoe components. You can find this item to purchase here: https://www.buildyourcnc.com/category/z-axis

Click the link to add information to this solution:
I HAVE BLACKTOE 4.1 WITH PORTER CABLE 890 ROUTER.TO CONVERT TO SPINDLE(2.2KW) CAN JUST CHANGE THE MOUNT?

You will need a Z-axis mount for Spindle if you are currently using a router.

Click the link to add information to this solution:
Do I need Z axis mount for spindle? I currently have router cnc blacktoe

We will have to replace the motor mounts that the router currently is mounted to. The process is easy we will need to communicate, through our email or over the phone.
@:customerservice@gmail.com
#:281-851-7701

Click the link to add information to this solution:
I own a blacktoe 2x4 cnc. I need to convert to 2.2kw spindle. I cuurently am using the porter cable router spindle.Thanks.

If you would like to use a spindle rather than a router on your existing CNC, we will send you another set of components that will allow the spindle to be mounted properly which includes the z-axis rails, rail support, spindle mounts and the dust shoe components. You can find this item to purchase here: https://www.buildyourcnc.com/category/z-axis

Click the link to add information to this solution:
I own a blacktoe 2x4 cnc. I need to convert to 2.2kw spindle. I cuurently am using the porter cable router spindle.Thanks.

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens, and nozzle. You will also need some mechanical parts and some motors, drivers, and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

If you remove the dust shoe, you should be able to reach the collet to remove the end mill.

Click the link to add information to this solution:
DO HAVE TO REMOVE THE PORTER CABLE 892 ROUTER EVERY TIME CHANGE BIT?

The 2.2kW Spindle has many advantages over a standard router such as the Porter Cable. The most obvious benefit to the user is the significant reduction of both dust and noise.

Additional Information:


Additional Information:
What size water source is needed and how long can it be used before it is too warm? Do you have a pressure vs. flow curve for the spindle so I can properly size the water pump?

Additional Information:
I used a small pond pump inside a 5 gallon bucket. I put a little bit of windshield washer fluid in with it to keep anything from growing in it. It's worked great. I've had 1 hour run times with no noticeable increase in spindle temp.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the 2.2 kW spindle. Does it run much quieter than a 2 hp Porter Cable router? You also mention a pump with a bucket of water. How long until the water is too warm to cool the spindle?

It is not recommended that standard routers do full depth passes. This is better done with a spindle. For best results with routers, we recommend a depth that equals the cutting diameter of the end mill. The IPM will relate to the chip load of the end mill (look up the formula online and add it here). The IPM will also depend on the end mill diameter, the larger the diameter, the faster the feedrate. A 1/2" end mill can cut about 300-500 ipm where a 1/4" end mill will be able to cut at 80-120 IPM, at a depth equaling the cutter diameter using a router. With a spindle, the same feedrates can be applied, but with more depth per pass. For instance, an MDF full depth cut at 3/4" can be cut at the 100 IPM using a 1/4" cutter.
Here is a basic setup we have for our blackFoot (default setting):
X-Axis
SPI: 914.29
Acc: 400.02
Vel: 5
Y-Axis
SPI: 1422.22
Acc: 400.02
Vel: 5
Z-Axis
SPI: 1600
Acc: 400.02
Vel: 79.98

Click the link to add information to this solution:
I have a BlackFoot with a 3.25hp Porter Cable router. What is a safe starting IPM to optimize feed rate? How fast do you guys run full depth passes through MDO or MDF?

The 800 series of Porter Cable routers all have the same diameter; therefore, you can purchase the latest model of that series and you should be fine with the fit for our router mounts.

Click the link to add information to this solution:
Which Porter Cable router should I purchase? The instructions say the 800 series, but I can't purchase an entire series, and don't know the difference between them.

That order did not show up in our system. We searched and found it in our PayPal activity. We are sending it today. My apologies for this.

Additional Information:
I received my order, thank you. However the collet nut will not fit my Porter Cable 690, the threads are too coarse. Can you please send the correct nut, and I will return the wrong nut.
Thank you,
Tom

Additional Information:
I believe the wrench is different also.

Additional Information:
Ok. I will send the correct wrench and collet nut.

Additional Information:
It’s Monday 11-16, and I have not received the nut and wrench. Have you shipped it yet?

Additional Information:
Let me check.

Additional Information:
The set of collets and nut/spanner came straight from the supplier PreciseBits. I am working to understand what went wrong and get it resolved.

Additional Information:
Do you have any new info on the status?

Additional Information:
It’s now Dec 2nd, I ordered this on Oct 7th. No resolution yet! Still waiting, Not very happy.

Click the link to add information to this solution:
I ordered a collet set for a Porter Cable router on 10/7, my card was charged on 10/8. I have not heard anything from you as to when it would ship, or even a confirmation of the order. Please let me know the status.

If you are using a router that will not fit into the router mount, it is best to have the mount requested from us. The mounts were designed with the appropriate thickness of material for structural purposes and to maintain this structure under load.

Click the link to add information to this solution:
Can I make the whole for the router larger? This is for a blacktoe and the whole is about 1/4 inch in diameter too small.

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

Sure. If you had your own computer to start with and now need a replacement for it, consider our redSprout and redLeaf systems. You can find information about them here: https://buildyourcnc.com/AssembledElectronics.aspx If you started with one of our assembled systems, and only need to replace certain components, contact our sales department at sales@buildyourcnc.com for a quote.

Click the link to add information to this solution:
Can I get a replacement computer only ? I have a blacktoe with parallel port and it seems to have stopped working.

The book (scratch build) will be able to cut at very high rates of speed, but the speed is partly determined by the mechanical setup. Cutting wood is generally recommended between 60-200 ipm depending on the end mill and spindle being used. The larger the end mill (with increased chip load capacity) the faster the feedrate.

If you are using a standard allthread, you will not be able to have these high feedrates. You will need to purcahse high lead leadscrews: https://www.buildyourcnc.com/item/mechanical-leadscrews-leadnuts-!5-5-starts-10-tpi

The stepping motors need to turn 13 times to travel one inch using standard allthread (1/2-13 TPI - threads per inch). The higher lead leadscrews shown in the link provided will move one inch with only two turns allowing the machine to move many times faster.

These speeds are especially important if you are cutting materials that have low melting points like aluminum and thermoplastics like acrylic, Plexiglas, etc. These materials require high feedrates and smaller depth per passes.

Additional Information:
20

Click the link to add information to this solution:
I just made the book build Cnc machine with the feed rate of 11.19 inch/min as suggested in book. Can I increase it to 20 inch/min? I have 2hp of router attached

We do offer discounts for academic institutions and instructors. Please contact us via the phone number above to inquire about our academic discount.

Click the link to add information to this solution:
I need to know if you have prices for educators, or other ways that a teacher could procure a blackToe 2'x4' CNC router. I apologize that this is sort of a bold question, as your routers are already well-priced.