[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 13566

Question: Does the Laser Controller work with Mach3?

Current Solution

The laser Controller will not work with Mach3.

Respond:

Other Possible Solutions to this Question

  • Is there any other software that will work with your controller Mach3?

    The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

    Click the link to respond:
    Is there any other software that will work with your controller Mach3?

  • Can the laser controller work with higher output laser tubes, like 150W?

    Yes, other CO2 laser tubes will work fine with our laser controller (including the Reci tube). Our laser controller is a digital based controller that controls the laser tube power supply, the motor drivers and other peripherals by outputting digital signals to these devices.

    Laser controller URL:
    https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

    Click the link to respond:
    Can the laser controller work with higher output laser tubes, like 150W?

  • Can other types of laser tubes work with the controller you are selling, for example, the 80W Reci tube?

    Yes, other CO2 laser tubes will work fine with our laser controller (including the Reci tube). Our laser controller is a digital based controller that controls the laser tube power supply, the motor drivers and other peripherals by outputting digital signals to these devices.

    Laser controller URL:
    https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

    Click the link to respond:
    Can other types of laser tubes work with the controller you are selling, for example, the 80W Reci tube?

  • Laser; does your new laser controller uses the stander g-code files??

    No, the laser controller does not run standard g-code. Instead it uses a version of a printer control language which provides optimal results when processing detailed images and designs. If you need or want to control your laser with g-code, however, you can do so by running it from a computer using a standard machine control software. You can even set your laser up to operate both ways. Feel free to contact us directly if you need help sorting through your options.

    Click the link to respond:
    Laser; does your new laser controller uses the stander g-code files??

  • When using the laser controller, what does "engrave beyond border limit" mean?

    LaserCAD: Engrave beyond border limit.

    This is caused by a sweeping motion that is too fast and where the acceleration is too slow. My recommended action would be to keep the acceleration the way it is and slow down the speed of the engrave sweeping motion. I typically use around 200-300 mm/sec and make sure that the axis sweep motion is the nozzle along the gantry, not the gantry itself. The gantry will have too much inertia to sweep, but the nozzle is very light and can sweep very quickly.

    Specifically, what is happening with the engrave beyond border limit is where that axis is not able to slow down fast enough to not hit the border. For instance, imagine a car going 100 mph and it needs to stop within 30 feet. This would not be possible because the deceleration is not high enough.

    Click the link to respond:
    When using the laser controller, what does "engrave beyond border limit" mean?

  • Does the usb controller (breakout) come with the needed usb cable?
  • Can you shortcut the usb controller that comes with the blacktooth laser to hardware reset it?

    The USB controller does not have a reset button installed on it.

    You have some alternate options however:
    - You can remove the USB connector and re-insert it.
    - Set the USB to use external 5v by removing the jumper near the USB connector, use a 5v wall adapter and install a switch along the 5v DC power line to turn it off then on. You can use a momentary push button switch to do this.

    Click the link to respond:
    Can you shortcut the usb controller that comes with the blacktooth laser to hardware reset it?

  • Can I use Mach3 or 4 with your USB controller PCA?

    The USB controller board is currently only compatible with Planet-CNC software.

    Click the link to respond:
    Can I use Mach3 or 4 with your USB controller PCA?

  • What file types will the anywells laser controller accept?

    LaserCAD and the Anywells Laser Controller used in our BlackTooth and Vertical Laser XL laser cutters and engravers can accept these file types:

    .nc (Gcode)
    .ai (Adobe Illustrator)
    .svg
    .pdf (Adobe Acrobat)
    .dxf (AutoCAD and Drawing Exchange)
    .plt
    .dst
    .dsb
    .uds (UD)
    .bmp (Bitmap image)
    .gif (Image)
    .jpg (Joint Photographers)
    .png

    Click the link to respond:
    What file types will the anywells laser controller accept?

  • What software is needed to run the laser controller from the PC?

    The laser controller uses software called LaserCAD. You can find the link to the LaserCAD software on the Laser Controller product page:

    https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

    Click the link to respond:
    What software is needed to run the laser controller from the PC?

  • Can the USB CNC Controller be used with LinuxCNC?

    The USB Interface can only be used with the Planet-CNC software which runs under the windows operating system.

    Click the link to respond:
    Can the USB CNC Controller be used with LinuxCNC?

  • how to control the spindle with the usb controller

    To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

    &index=44&list=PLE72E4CFE73BD1DE1

    Click the link to respond:
    how to control the spindle with the usb controller

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to respond:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • Will the USB breakout board work with Mach3?

    Our newer USB board will work with Mach3 and can be found here at this URL:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    Will the USB breakout board work with Mach3?

  • can your vacuum pump controller card work with a 1-1/2 HP single phase 200v motor?

    The relay on the Vacuum Pump Controller can handle up to 250V and 12A. If your vacuum pump falls below those values, then the vacuum pump controller will work.

    Link to the vacuum pump controller:
    https://www.buildyourcnc.com/item/electronicsAndMotors-pneumatic-hydraulic-vacuum-pump-controller-sensor-redfrog-v1

    Click the link to respond:
    can your vacuum pump controller card work with a 1-1/2 HP single phase 200v motor?

  • Will Mach 4 work on the Controller board that is meant to run Mach 3?

    The Mach3 USB board found here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Is not designed to work under Mach4. The Mach3 USB uses a plug-in in Mach3 to function as an interpreter, sending pulses and signals to electronics from commands sent to the board from Mach3. This plugin would need to be updated to be able to work under Mach4 but the board manufacturer would need to do this update. So far, there is no plug-in that will work for Mach4 and this board.

    Click the link to respond:
    Will Mach 4 work on the Controller board that is meant to run Mach 3?

  • Will the mach3 usb interface card work with Windows 7?

    Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

    Click the link to respond:
    Will the mach3 usb interface card work with Windows 7?

  • I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

    If you are getting the "Communicating Unsuccessful!" error when you are trying to communicate between LaserCAD and the AWC608 Laser Cutter and Engraver controller (after you have already tried installing the USB driver from the LaserCAD setup procedure), these are the steps you will need for a successful communication:

    - Open the Device Manager window (right click on the start menu and select Device Manager)
    - When you plug the USB cable from the AWC608 Laser Cutter Controller (USB Type B connector) to the computer, you should see a new item in the Device Manager, possibly under "Ports (COM & LPT)", or under "Other Devices". It may show as an item under "Other Devices", possibly FT245R and has an "!" in a yellow triangle.
    - Download the latest FTDI drivers from: http://www.ftdichip.com/Drivers/D2XX.htm
    - Unzip the files to a folder that can be easily browsed.
    - Right click on the item that appeared in the Device Manager when the cable was plugged in between the Laser Cutter AWC608 controller and the computer.
    - Click on update driver
    - Select the procedure to manually install the driver and browse to the folder containing the FTDI driver and follow the step in the driver installation wizard.
    - The item should now be located under the "Ports (COM & LPT)" and should be named "USB Serial Device (COM#)". The # will be the number you will use in the LaserCAD software.
    - In the LaserCAD software, click the "Select Mode" at the far top right of the Laser CAD user interface.
    - Make sure USB mode is selected.
    - If the Machine name with the correct COM number is listed, select it and exit the dialog window. Otherwise, click on "Add" and fill in the details with the new COM number.

    Additional Information:


    Additional Information:
    Communicating unsuccessful

    Additional Information:
    Communicating unsuccessful

    Click the link to respond:
    I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

  • Does the USB controller come with driver installation instructions so we could create our own user interface to communicate with the motor?

    You can use a Pickit 2 programming to load firmware onto the usb driver. The USB use a Microchip pic microcontroller. If you can manage writing a program for the Pic microcontroller and have a Pickit 2 firmware uploader (programmer), you should have no problem.

    Click the link to respond:
    Does the USB controller come with driver installation instructions so we could create our own user interface to communicate with the motor?