CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
Are there any instructions for use the USP breakout board for a CO2 laser?

You can go here to find the diagrams and instruction on connecting the parallel breakout board:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Also, please make sure to watch all of the electronics tutorial videos here:
https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
how do I connect the parallel breakout board?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Getting continuity from the x--/x++ might not mean it is a faulty board, unless they are bridged, so both get a pulse rather than one. But to check if you might have a opposite connection for those input:
Planet-cnc/file/settings/input/invert inputs/input 1/input 2.

Additional Information:
In input port section in config. Scroll down and you will see THC On, Up and Down. Enter your input pin numbers there.

Click the link to add information to this solution:
Installing THC to my limit ports on the breakout board. Once wired how do I get Mach 3 to reconize the port?

I suppose you are trying to determine how to connect the VFD tothe relay on the breakout board. This is possible, however, not recommended as there is a more robust way to connect the VFD to mach3 or mach4 that allows that CNC machine control software to control the speed and other features of the VFD.

Follow the instructions from this question (number 13383):
https://buildyourcnc.com/FAQ/13383

To get to this answer, you can also ask this customer service "How can I connect my spindle's VFD to mach3?"

Additional Information:
If you still want to connect the VFD through the relay, I will clarify this instruction on this question tomorrow as I don't have the information in front of me at this moment. Thanks.

Click the link to add information to this solution:
I need wiring diagram from mach3 breakout board to hy inverter

You can go here to find the diagrams and instruction on connecting the parallel breakout board:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Also, please make sure to watch all of the electronics tutorial videos here:
https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
I can't find the diagram to hook up the parallel breakout board

Probably.

Click the link to add information to this solution:
Are there supposed to sockets on the breakout board I picked up yesterday?

The breakout board does not require software to run, specifically. The breakout board serves only as a signal conditioner where the input signal from the computer is output at the corresponding terminal, or the terminal receives a signal and is conditioned and sent to the parallel connector to be read by the computer. As long as the software can communicate to the parallel port of the computer, then the breakout board will function.

Click the link to add information to this solution:
Do the 5 Axis Breakout Board with Relay requires software to setup

Yes, we see the order of the USB breakout board in our system to be shipped. The order is in the shipping process. The shipping label has not been created yet, but will be by the end of day.

Click the link to add information to this solution:
you didn't answer the question, also I ordered a usb breakout board

You can find the cnc machine interface board here that works with Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This board will work with Mach3 and Mach4. The board is filled with a wealth of options and features, including the ability to connect up to 8 axes (motor drivers), pendant, LCD, many outputs and inputs, separate pins for limit switches , 2 relays, Ethernet and USB interfacing.

Additional Information:

Click the link to add information to this solution:
What interface or breakout board do I need for Mach4?

The mapping of the input pins of the parallel breakout board is configured through software. The input pin are very versatile and can be mapped to all kinds of different types of input including axis limits and axis homing.

Click the link to add information to this solution:
Is there a mapping on the input (switch) pins to an axis on the parallel breakout board?

Our electronics kits with the parallel breakout board will work with Mach 4, however you will need to purchase the Legacy Driver for Mach 4 to work with our breakout board.

Click the link to add information to this solution:
I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

Click the link to add information to this solution:
can I use the usb on the parallel breakout board with planet cmc

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

Click the link to add information to this solution:
Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

It is not necessary for a wiring diagram for the breakout board to the SuperPID controller since you are only going to connect two wires from the breakout board output terminals of your choosing to the SuperPID controller. The only thing remaining is to configure Mach3 so that the spindle control section serves as the SuperPID controller.

To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

Click the link to add information to this solution:
Do you have a wiring diagram for your breakout board and the SuperPID?