What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

Try slowing your feedrate down and increasing spindle RPMs. End-mills will leave a poor finish if you go too fast. Make sure your cutting depth isn't too much. Maybe the endmill or cutter is blunt? Could it be the feed direction of the cutter? Some materials need to be fed in a certain direction.

Click the link to add information to this solution:
MOTOR GOING TWO DIRECTION WHEN JUST PUSH UP. IT WILL GO DOWN AND THEN GOES AGAIN UP WITH THE SAME BUTTON.

See the question on our "Ask the Expert" question-and-answer list on cellular towers under nonionizing radiation for a discussion of RF safety issues associated with cellular radios. The technology underlying cellular radios and base station antennas is similar around the world, but there are differences in systems design and RF safety limits in different countries. For a summary of cellular radio RF safety issues with attention to international differences see the excellent Web page, Cellular Phone Antennas (Base Stations) and Human Health, by John E. Molder, Ph.D., from the Medical College of Wisconsin. Gary H. Zeman Sc.D., CHP

Click the link to add information to this solution:
I LIVE IN ITALY AND WISH TO KNOW MORE ABOUT RADIATIONS CAUSED FROM MOBILE TELEPHONES. TELECOM WOULD LIKE PLACE A WIRE-ANTENNA THE HEARTH OF MY TOWN, I'M AFRAID IT. WHICH KIND RISK HEALTH COULD IT CAUSE? THANK YOU IF WILL SEND ME SOME INFORMATION SCIENTIFIC ARTICLES THIS PROBLEM!

Thank you for your inquiry about the risk to your embryo by using a cellular phone during pregnancy. Sometimes it is not made clear to the public that there are different kinds of radiation. The electrical fields from a cellular phone are nothing like x ray. The energy is so low in the electrical waves of cellular phones that it does not represent a risk to the developing embryo. If you use the cellular phone conventionally by placing it to your ear, you further reduce the exposure to the embryo, which is already extremely low because of the distance of the phone from your ear to your uterus. There are no studies dealing with the risks of cellular phones on the outcome of pregnancy in humans, but numerous animal studies indicate that the exposures from the phones do not represent a risk for birth defects or miscarriage. Of course you must realize that every healthy pregnant woman begins her pregnancy with a 3% risk for birth defects and a 15% risk for miscarriage. Good luck with your pregnancy.

Robert Brent MD, PhD, DSc(Hon)

Click the link to add information to this solution:
WILL IT BE HARMFUL TO USE MY MOBILE PHONE DURING PREGNANCY? IF HARMFUL, SHOULD I DISCONTINUE USING OR MODERATELY?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
BUT DIDN'T SEE ANYTHING ABOUT COOLING THE LASER OFF - IS YOUR SETUP LIKE MOST OTHERS NEED BUCKET OF DISTILLED WATER TO PUMP THROUGH MACHINE?

You can actually select many places for the switches, depending on where you think your zero will be. I will take pictures of where we positioned our switches. We set the positions so the zero is at the bottom left corner of the machine.

Additional Information:
I will take pictures tomorrow.

Additional Information:
Thank you. Just want to finish before the holiday.

Additional Information:
Not a problem at all and my apologies for not having that information. I have been meaning to put up a video on the limit switch connection as it is somewhat difficult to explain the process in words and diagrams.

Additional Information:
Any update?

Additional Information:
I plan on driving to the office later today and take pictures.

Additional Information:
Thank you. I've just done almost everything else. Just waiting for the grade 3 grease in the mail. Also, where do you suggest connecting the cable carriers? I ran everything through the top but the carrier is getting kind of full. Because of that, it is pushing the belt out when the gantry moves.

Additional Information:
I will take pictures of those connections as well.

Additional Information:
Much appreciated.

Additional Information:
It’s my pleasure.

Additional Information:
I’m almost to the office. I’ve been shuttling my kids around today. Sorry for the wait.

Additional Information:
I’m adding the images to the end of the VLXL instructions.

Additional Information:
The limit switch connections use the NO (Normally Open) terminals. That means that the switch, when not engaged, is normally open (no connection between the com and the NO terminal). When the switch is engaged, then the connection is closed and the NO and COM terminal become connected, making a circuit.

Additional Information:
Did you bend the arm on the x switch? Or can you mount it flush with enough give to trigger? Same on both sides?


Additional Information:
It does look like it is bent in the picture. No, you do not need to bend the arm of the rotary switch.

Additional Information:
We only have the rotary switch on one side.

Click the link to add information to this solution:
How do I wire the limit switches on the VLXL? Also, where do I place them? You included 2 rotary and two other limit switches.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

Yes Mach3 is a great program. Our 3 axis is 6'X12'X3'using all BYCNC components (incl. redsprout)

Click the link to add information to this solution:
I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

If you purchase the Vertical Laser XL in kit form, then we would be able to deliver it within 2 weeks. If you want the Vertical Laser XL to be assembled, we would need a minimum of 1 month.

Additional Information:
What is the shipping cost to rural WV? Mannington, WV.

Click the link to add information to this solution:
Hello! How fast could I get a VLXL? Looking to get it by the end of the month. In WV. Ben

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

It is not clear that mobile phones do produce brain tumors, or any serious health effects for that matter. A number of epidemiology studies have been almost completely negative on the issue.

See the article I wrote with John Moulder in IEEE Spectrum magazine and also Moulder's FAQ on mobile phones and health.

There has been a lot of discussion over the years about the possible mechanisms by which microwave energy such as emitted by cell phones might produce biological effects. The one unequivocal mechanism is the heating of tissue, but mobile phones operate at power levels that are too low to cause noticeable heating in the user. Scientists have speculated about other mechanisms, but these theories remain unproven and many of them have been challenged on biophysical grounds.

Whatever may be the risks or nonrisks of mobile phone radiation, a hands-free kit is an effective way for the user to reduce his or her exposure to radiofrequency energy while using a mobile phone.

Kenneth R. Foster, Professor
Department of Bioengineering
University of Pennsylvania

Click the link to add information to this solution:
I WOULD LIKE TO INQUIRE ABOUT THE PHYSICS PRINCIPLES REGARDING USE OF MOBILE PHONES AND DEVELOPMENT BRAIN TUMORS. I'VE BEEN THROUGH MANY SITES BUT THEY CAN NEVER GIVE AN EXACT ANSWER. REALLY SOMEONE TUMORS OR DOES IT HAVE DO WITH INTENSITY RADIATION DISTANCE BETWEEN PHONE INDIVIDUAL?