When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
[77] I am having troubles finding the PD program, I have the Pd but it doesn't show everything I need to program my VFD. Any help will be appreciated...

Dealing with a larger offset when cutting a larger object, try calibrating your machine accordingly (

Click the link to add information to this solution:
I am having trouble with my cutting precision. I can cut a 1" box within 0.005" accuracy, but when I try to cut something with a 6" profile, it cuts almost 0.125" heavy. Any help would be greatly appreciated.

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

In regards to getting a complete plug and go system, there are a lot of items to consider.
Electronics, DYI or one of our electronics kits that come assembled and tested?
Cable for the motors is a additional purchase, spindle? = silicone tubing/water pump, etc.
Cable carrier (wire management), software (also additional purchase).

We can view your cart, but please send us your email and username to customerservice@buildyourcnc.com so it will remain secure!

Click the link to add information to this solution:
I want to by a 5 by 10 foot kit, sorry, I don't have the time to read everything here. what should I be thinking about, Can you veiw my cart and tell me what else I need to get?

Have you tried a different input pin?

Customer response:
I've tried all pins: 10, 11, 12, and 13. I get the same non-response in each case.

Recommended action
There may be a problem with the board. If you are using our parallel breakout board, we can ship you a replacement (call us), otherwise, you will need to determine the problem with the vendor of the breakout board you are using.

Additional Information:
I have tried 3 different breakout boards from 3 different providers and they all do the same thing My limit switches are microswitches wired NC with each axis wired to the BO Board. I have checked each circuit and all is OK to the BO board. each circuit has continuity at the board and when any switch is pressed the circuit breaks. Mach 3 does not recognise that the switches are even there. They are configured as active low Do you have a suggestion.

Additional Information:

Click the link to add information to this solution:
I'm having trouble getting Mach3 to recognize my limit switches. I've eliminated everything back to the breakout board. I can directly connect Input 10 to GND on the breakout board while Mach3 is in autorecognize mode and Mach3 doesn't acknowledge anything.

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Currently the only options available for our computer systems, are for our machines which included all the motors and drivers. If you would like to talk about a custom order, please email (customerservice@buildyourcnc.com).

Click the link to add information to this solution:
Do you sell the computer system only ? My Dell has given up the ghost. I may want to buy the PC, Power and case. I have everything else.

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

If one or more motor is not responding, please follow the troubleshooting directions below:

For parallel Bob only! Make sure both the parallel and USB are connected.

Re-check wiring, and connections for continuity (no breaks in the wires) and check for correct wiring locations from driver to BoB.
Check dip switch settings on the driver.
Check components, by swapping the motors (ex. y-axis motor to z or x-axis driver and z or x-axis motor to y-axis driver) to check if motor functions on another driver.
Depending on software check step low active (mach 3) or invert pulse (planet-cnc) for the axis which is not responding.
Mach 3 - config/port & pins/motor outputs / Planet-CNC - file/settings/axes

Click the link to add information to this solution:
I have an engine NEMA 34 from Y axis on my green bull that do not response, I already check connections and everything seems to be OK, how can I check that the motor it's working properly or not?

Is this regarding the Mach3 USB controller?

Click the link to add information to this solution:
I'm having a problem with my controller card: I can measure 24 volts going to the card, but when I set Mach3 outputs I reagister no voltage. Please help

My apologies for not getting back to you. We always answer the phones during business hours, so I would try that first. Our emails on Monday generally is stacked up as we are closed during the weekend. We can try your g-code here. Please send the g-code to the techsupport@buildyourcnc.com email address and we will test the code to see if it works.

By the way, do you get movement on the planet-cnc UI screen?

Additional Information:
The program starts and runs normal. I have all the correct movement on the mill and the UI screen. Then one of two things happens. It either stops and resets all axis to zero in the middle of the part or it freezes in the middle of the part. When it freezes, it is not moving on the cnc or the UI screen. Sometimes after a freeze it will come up with an 'IO timeout error', but the only way to clear is to unplug USB and start over.
I will send my settings and g-code files over tonight. Please be sure to load my settings when running the g-code. No movement of the cnc is necessary as the controller will do these issues without power to any drives and just the USB board connected, on my board at least.

Click the link to add information to this solution:
I have a MK1 board that I just got running and I am having issues. Do you have an MK1 board at your shop that I can send you my G-Code to run? The freexing/zeroing in the middle of the program issue happens even with no step drives attached to the board.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a cnc router with twin ball screws on the long axis and I will have a rotary axis as well. I need a 5 axis breaker board using only 4 axis total. Can you help me?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

with parallel port controllers, you have the ability to jog using two axes at the same time, but with USB controllers, this is not possible.

Click the link to add information to this solution:
[575] Hi, I recently purchased this board and everything seems to be fine! But I am not being able to jog two axis at same time as I used to do on my older board. Did I do something wrong?

If you are wanting to use servos, I would highly recommend using closed loop steppers and drivers. You will get the best features of both the servo closed loop and the exact digital positioning of stepper motors.

For controllers: the pokeys57cnc will work with either Mach3 or Mach4
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Otherwise, you can use the Mach3 USB controller if you only an on using Mach3:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
Hi there. I have an ex school Boxford HSRmi2 sat in my workshop, good condition and I'm assured it's all ok, but I want to rip everything out and go down the Mach 3/4 rabbit hole with servos. I need help at this point as I haven't done anything like this before and have no knowledge of controllers/motors etc. Could someone please point me in the right direction? Thanks.