That is difficult to tell at this time. Right when we get them in, they go fast. These items come from China and the units are shipped in via freight on ship, so there are many factors on the delivery such as weather.

Click the link to add information to this solution:
When will the 2000 mm HIWIN Spec Linear Guide rail be available?

Are you using the control panel (front panel with the speed control knob known as he potentiometer)? Or are you attempting to use the computer to control the speed?

Additional Information:
I am using the control panel, however there is no knob on mine, just buttons.

Click the link to add information to this solution:
Hello, I bought your 110v 2.2kw spindle and vfd. When I turn it on it reaches the full 24000 rpm, but will not let me decrease the speed. How Can I fix this?

The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?

When an order is complete, and is for local pickup, you will be called by the shipping department to let you know it is ready. At that time you will be given the address.

Click the link to add information to this solution:
I placed my order online and selected local pick up. How will I know when the order can be picked up and what is the address?

To calculate RPM use this formula, in which you will have to find RPM's when you have Hz.
1 RPM = 0.01666666667 Hz
Formula: 0.01666666667 × RPM = Hz
On our VFD if you select the >> button about 3-4 times, it will change from Hz, A, or ROTT.
When the LED's are lit on Power, FOR, and ROTT, you should be able to see the RPM the spindle is running at, our maximum setting for these spindles is 400Hz / 24000 RPM.

Additional Information:


Additional Information:


Additional Information:
press the shift key on the key pad and the led at the top of the display will move to the right until the Rot (RPM) led is lit the display will now show RMP


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How to I calculate RPM based on hertz displayed/set on the 2.2kw VFD (110V AC version)?

We have the image at that size to encourage the purchase of the kit from us. This helps to keep buildyourcnc alive and allows us to fund development of other awesome low cost machines.

Click the link to add information to this solution:
could you make available a larger size picture of the exploded view of the BlackTooth laser cutter? I would like to use for reference when building my laser cutter, but it is too small to be really useful.

the 2.2kW spindle uses the ER20 collet by default. The ER20 collets can accept shanks as small as about 1mm all the way up to 9/16 inches or 13mm.

Click the link to add information to this solution:
Is the 2.2kW spindle available in an ER20 collet option?

Please use these settings for our 110V VFD's:

Change PD001 to '0' or '1' (source of run commands/one will be computer controlled)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 110 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution)
For further info please refer to (https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd#prettyPhoto/9/) for wiring and other specifications.
Please check you wiring to be correct as the illustrated photo on the diagram.

Additional Information:
PD003 should be set to the base operating freq. stamped on your motor/spindle typically 400hz

Click the link to add information to this solution:
How should I configure the 110v vfd with 2.2kw spindle? When I use the configuration on the spindle page, I get an over-current error (e.oc.a).

The motors could be wired incorrectly causing them to lock up. Make sure to check the wiring to make sure the X and Y are connected to the correct terminals.

Click the link to add information to this solution:
When Blacktooth is powered on the motors get power but will not turn. What should I do?

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Cutting metal with lasers even at 100W and 130W is difficult. The main problem is molten is a byproduct of lasing, which can severely damage the laser.

Click the link to add information to this solution:
For the XL Vertical Laser Machine I see it won't cut metal as it is only 80w. However, I noticed that you are working on 100w and 130w versions so will that be sufficient to cut through sheet metal? If so, how much longer until those are available?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

According to the supplier of the 2.2 kW spindle, the safest operating speed for the spindle is 6000 RPM. The supplier also stated that theoretically, the spindle can operate from 0 to 24,000 RPM. I am continuing a dialog with the supplier to delve deeper into understanding the configurations and ramifications of such configurations for operations outside of the safe boundaries into the "theoretical" ranges.

Additional Information:
20

Click the link to add information to this solution:
I would like to know what the lowest rpm that can be acheived with the 2.2kw spindle and inverter and still have enough torque to drill

If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

Click the link to add information to this solution:
I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

If you do not find a machine, mechanism, or resources on this website, we can assist you and guide you on how to use the resources on this website to suit your needs.

Click the link to add information to this solution:
If no existing kit seems to match the requirements, is design assistance available so I could build the needed platform myself?

If you need technical support for the 220V VFD, you can ask the specific question on the customer service section of the website. Link below:
https://buildyourcnc.com/CustomerService.aspx

Click the link to add information to this solution:
Do you know of any technical support for the 220 Volt VFD you sell? I can't find any help on it.

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the USB interface board? Is there a CAD model available?

VFD settings........
1) To program the VFD, wire it up, plug it in. It takes several seconds to come to life.

2) Push the PRGM button to enter programing mode.

3 )Push the SET button. The display will read PD000.

4) If you push the SET button again, it will display the present setting of PD000.

5 )By pushing the up or down arrows, you can change the setting to whatever it needs to be. (This is just an example. PD000 needs no changes)

6)Push the SET button again to lock in the setting of PD000 and advance to the next number, in this case, PD001.

7) Push the SET button and it will display the present setting of PD001. Again, use the up and down arrows as necessary to set PD001, then push SET again to lock it in.

Note: You can also scroll through the PD numbers with the up and down arrows.

8) make all settings this way.

9) by pushing the SET button you can scroll through the settings. First push of SET moves to the next number, second push displays it's setting, third push moves to the next PD number.

Note- If you take too long, it will leave the programing mode on it's own. If it does, just push PRGM again to return to programing mode. Then press SET and continue what you were doing.

10) Start with PD013. Set it to 1, which returns the settings to the factory settings.

11) Then set PD005 to 400, PD004 to 400, and PD003 to 400 IN THAT ORDER.

12) Then set the following: PD041=8, PD144=3000

13) Set PD209=50

That's it for the programing. You should get 24000RPM when you push RUN.

Click the link to add information to this solution:
I JUST RECEIVED A REPLACEMENT SPINDLE (2.2KW 220V). HOWEVER, WHEN ATTEMPTED IT USE THE NEW SPINDLE, WOULD ONLY REACH 1500 RPM. IS THERE SOMETHING NEED TO CHANGE ON CONTROLLER?