If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

Depending on the size of your CNC machine, it will vary the length required for your application.
Please verify the CNC machine, and we can go into detail on the specific lengths or methods for the linear guide mechanics.

We sell our ACME Screw (1/2" per inch), also our longest length of ACME Screw is 76-3/4".

Click the link to add information to this solution:
Hi, I need the lead screw and bearings for x/y/z axis of the CNC. What is the length of "1/2" Lead Screw per inch (Steel)"?

Yes, the blueChick kits are available. You can get the shipping rates automatically in the shopping cart. There will be a calculate shipping button on the enter shipping information section of the shopping cart.

Click the link to add information to this solution:
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?

To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

Additional Information:
MUAR-QVXU-CAYW-CBWQ


Additional Information:
MUIS-RQPB-PTHB-QTTB

Additional Information:
MUIH-EERP-IADB-TRIP

Additional Information:
9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

Additional Information:
Key: LUQR-BQYI-SCEW-QVBT

Additional Information:


Additional Information:
after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

Additional Information:
MUJR-BISM-KRDN-KKER
056971

Additional Information:
0561234

Additional Information:
MURL-QPQU-EGBJ-FNMB

Additional Information:
MUCE-LFMQ-WBCW-MLHO

Additional Information:


Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
looking for registration key for MUUK-IBTW-ECTL-CJWD

Additional Information:
MUXO-PIYY-KNHD-RKLY

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:


Additional Information:
MUEY-YLJU-OBRR-LJBV

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:


Additional Information:


Additional Information:
MULY-XRYF-BBDN-FBWP

Additional Information:


Additional Information:


Additional Information:
how to generate activation code richauto a11

Additional Information:
MUJC-LNIL-EOHS-YKNQ

Additional Information:
sdfd

Additional Information:
m l

Additional Information:
MUXC-RWKB-PKAL-HGNN

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Click the link to add information to this solution:
THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
However we currently do not have any plans available for public use/distribution.

Click the link to add information to this solution:
I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

The instructions for assembly are found in the book. If you are interested in purchasing the plans and instructional DVD please see this link https://buildyourcnc.com/cnckitintro.aspx

Click the link to add information to this solution:
I read the book and i want the vedios show assembly the CNC Machines please give me alink for vedios

These files are no longer available. We suggest purchasing a kit, like the blackToe, or blackFoot as these kits are far more rigid and perform much better.

https://www.buildyourcnc.com/blackToe2x4v40.aspx

https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4

Additional Information:
20

Additional Information:

Click the link to add information to this solution:
Would you be able to provide .DWG/.DXF files instead of .NC files for the CNC Routing Machine Kit Version 1.3 please?

Yes, the 2'x4' CNC router (blackToe) cuts within the full 2'x4' dimensions and a tiny bit more.

Link to the machine:
https://www.buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
Does the 2X4 ft CNC model allow cutting a 2X4 ft board or what is the cutting demeninsions? Thanks

The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

Click the link to add information to this solution:
what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

These are the recommend values(default) for our blackFoot CNC machine, the acceleration and velocity can be adjusted as high as the motor can rotate without stalling! Suggested increment's will be by 10's.

blackFoot:
X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 5.43A
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in, Velocity 400.02, Acceleration 4
Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in, Velocity 400.02, Acceleration 4
Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in, Velocity 79.98, Acceleration 5

Additional Information:
how can we tuning the CNC motor

Click the link to add information to this solution:
Motor tuning. While motor tuning what are the recommended steps per inch, velocity, and acceleration for the BlackFoot CNC?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Ok, sure. Let's get the discussion started. Please respond with your questions on this FAQ

Click the link to add information to this solution:
Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

The steps per inch is dependent on the microstepping:
Steps/Inch for the x and y
Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
steps/inch = 3200 / 3.5 = 914.28
This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

Velocity:
Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

Acceleration:
Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in
Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in
Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Additional Information:


Additional Information:


Additional Information:
4th axis


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
While motor tuning what are the recommended steps per inch, velocity, and acceleration for the GreenBull CNC?

I recommend using a wireless pendant rather than one that is wired to the controller.

Here is a link to one on Amazon.com: https://amzn.to/3r3AfTm

This is an affiliate link.

Click the link to add information to this solution:
[596] I am new to CNCs, curious to know what I need to look for in a pendant that would be compatible with this board and Mach4?