I can send you a new license. All you need to do is email me at customerservice@buildyourcnc.com and state the name the license is under and I will send you another license.

Click the link to add information to this solution:
I had to reset windows on my computer and in so doing, I lost my Mach 3 program. I tried to re-download it, but the license is expired. How can I reinstall the program? License # 44y5-Version R3.043.062- Bought about May 12, 2020

If you already have a Mach3 license, you don't need to purchase another one. The license is connected to you rather than the computer. Mach4 is licensed to the computer, but you are able to have multiple computers for each license, and can be switched from one computer to another.

If you purchased the license from me, you can call (make sure to leave a voicemail), or email to get a re-issued license.

Click the link to add information to this solution:
[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine. I will have to buy a new license for the Mach 3 so will need to get the interface board I have to talk to MAch 3. Can I get just the disc or is there a place I can download what I need?

Does your plasma cutter have an external trigger that voltage can be applied to make the trigger engage? If I known, please provide the brand and model of your plasma cutter so we can determine this.

Additional Information:
I converted my blackToe to do plasma cutting. Used the Motor control relay on the break out board and just wired it into the plasma cutter trigger. Put a large pan (like a car oil drip pan) with about 1/4 inch of water on the table and attached fixtures. 400 15ga parts later it's still working great.

Additional Information:
That is so cool!!

Additional Information:
I would like to post a story on your setup and conversion. Do you have pictures of the process and/or the new setup?

Click the link to add information to this solution:
Hello I bought a full setup of parts a couple years ago to make a cnc router and now I have decided that I want to make a cnc router/plasma. I was wondering how to go about hooking up the plasma to the breakout board

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

Mach3 and Mach4 typically use specific controller cards that are compatible with the software. If your controller connects to your computer using either a USB or Ethernet connection, then you will probably need to change the controller card as well, unless your controller card contains a plug-in that works with the Mach3 or Mach4 software.

Click the link to add information to this solution:
I have cnc fiber laser cutting machines it has operating software cypcut and I need to change it to Mech 3 or 4 do I have to buy the driver card with the software or only the software?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

We are developing plans for our machine, but they are not completed yet. Please let me know if you would like to be added to our list of customers wanting plans. Thanks,

Additional Information:
If you have specific questions regarding CAD, CAM and Control, please add another question to the customer service and I will answer them in detail.

Click the link to add information to this solution:
How do I get started I would like to build a cnc router. Making the machine I can do, but I am weak on cad,cam and mach3. I am thinking about a 4’x4’. Do you have plans I can buy?

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Yes, if you are using 1/2" standard allthread lead screw coupled to your stepping motors, you can increase the speed by changing the lead screw to 10 TPI 5 Start Lead Screws with antibacklash nuts. This will allow you to have up to 200-300 IPM (inches per minute) travel and cutting speeds.

The reason why the feedrate and jogging speed is faster is because the lead screw will travel a farther distance for each turn of the motor. A standard allthread will only travel one inch after 13 turns of the motor. The above (link below) 5 start 1/2" lead screws will travel one inch with only 2 turns of the motor! That is a drastic difference and you will get more torque from your motor since most of the torque is present at low speeds.

Lead screw link:
https://buildyourcnc.com/item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi

Antibacklash nut link:
https://buildyourcnc.com/item/mechanical-leadscrews-antibacklash-nut-!5-5-starts-10-tpi

Click the link to add information to this solution:
I built a 2' x 4' cnc about 2 years ago and bought all the plans and part through this website. My average 2D design takes approximately 35-40 minutes to complete. Is there a way to make my cnc faster?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I just wanted to know what I can expect to pay to build the blackFoot 4'x8' CNC machine, excluding computer, software and router? Is the kit complete or do I have to purchase additional items to finish?

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus

We recommend checking the dip switch settings on your drivers, having the correct microstepping/amp settings along with the steps/unit will help the motors run as effective as possible.
This is a default parameter that we use while we test our motors:
Driver dip switch settings will be at a 1/16 microstepping and 2.7amp (11001100) for x/y-axis and the z-axis will be at 1/4 microstepping and 2.7amp (10101100).

In planet-cnc with increasing the motor speed, you will have to modify the settings in planet-cnc (File/settings/setup) you will modify the initial speed, maximum speed, and the acceleration.
X/Y-axis step/unit: 1422.22 initial speed:500 maximum speed:750 acceleration:25
Z-axis step/unit: 1600 initial speed:100 maximum speed:300 acceleration:25
The initial speed and maximum speed will have to be roughly tested and adjusted per application.
Make sure to adjust the JOG slide bard underneath the axis controls on screen to about 750, to compensate for your x/y-axis adjustments. If left alone the speed will max out at the default setting.

Here is a video tutorial to calculate the steps required depending on your mechanical linear motion components. (

Click the link to add information to this solution:
I bought Nema 24 motors and driver package with usb board. What do i need to have more speed? Cant even jog past 25 ipm without the motor stalling (not having enough torgue)

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?