The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

Send me an email so I can confirm the purchase. customerservice@gmail.com

Click the link to add information to this solution:
I purchased a brealout board a couple days ago and it does not show under my account as being purchased, the cash was drawn from me. I assumed I could look and see it in my account and get a tracking number when it is shipped

If your PC is unable to communicate successfully with the Mach3 USB controller that you purchased, the problem can exist outside of the controller. If the problem is with the controller, then my controller will work. If the problem is not with the controller, then the problem will persist.

Click the link to add information to this solution:
[575] I have one of these but pc says device is faulty. If i buy one from you will you be able to fix such problems

To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

Additional Information:
MUAR-QVXU-CAYW-CBWQ


Additional Information:
MUIS-RQPB-PTHB-QTTB

Additional Information:
MUIH-EERP-IADB-TRIP

Additional Information:
9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

Additional Information:
Key: LUQR-BQYI-SCEW-QVBT

Additional Information:


Additional Information:
after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

Additional Information:
MUJR-BISM-KRDN-KKER
056971

Additional Information:
0561234

Additional Information:
MURL-QPQU-EGBJ-FNMB

Additional Information:
MUCE-LFMQ-WBCW-MLHO

Additional Information:


Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
looking for registration key for MUUK-IBTW-ECTL-CJWD

Additional Information:
MUXO-PIYY-KNHD-RKLY

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:


Additional Information:
MUEY-YLJU-OBRR-LJBV

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:


Additional Information:


Additional Information:
MULY-XRYF-BBDN-FBWP

Additional Information:


Additional Information:


Additional Information:
how to generate activation code richauto a11

Additional Information:
MUJC-LNIL-EOHS-YKNQ

Additional Information:
sdfd

Additional Information:
m l

Additional Information:
MUXC-RWKB-PKAL-HGNN

Click the link to add information to this solution:
THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

In the tracking for that package, it says it was "Delivered, Garage or Other Location at Address". The package was probably too large to insert it in the mail box. If it was delivered on your porch or garage as stated in the tracking, then a person may have walked away with it. Call your local USPS office and inform then that your package was not where it stated on the tracking.

Click the link to add information to this solution:
I have not received my order even though USPS says they delivered it to my home. Its nowhere to be found. The tracing number is 9405511699000140422765, please help me.

This may be less of an issue of the grasp that the feeder has on the filament and more an issue of the heat getting to the plastic at the hot end, or having enough heat at the hot end. Try increasing the temperature and try again. If that doesn't work, make sure you are insulating the hot end sufficiently to keep the hot end hot enough to keep the plastic melted.

Click the link to add information to this solution:
The 3d printer filament is not feeding. It is heating and will melt and feed some but not consistently.

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
Will it be possible to only buy the CNC plans, I live in South Africa and shipping is very expensive...

It may be tough to rotate a stepping motor by hand prior to energizing it especially if it is a large motor above 400 oz-in.

Click the link to add information to this solution:
I received the 425 oz-in motor from you. Is it supposed to rotate freely by hand when not powered?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
Hi there, when the gantry bumps up against a limit switch and triggers it, how do you tell Mach3 to allow me to jog the motor away from the limit switch? ie: I can't press RESET because the limit is open.... how do I move it? Thx.

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
Hi there, when the gantry bumps up against a limit switch and triggers it, how do you tell Mach3 to allow me to jog the motor away from the limit switch? ie: I can't press RESET because the limit is open.... how do I move it? Thx.

I will check

Additional Information:
The license was purchased and the developer is sending you the license shortly.

Click the link to add information to this solution:
Hello. I purchased a Mach 3 Pro License and have not received it yet. How long should it take to send me the access code ?

It looks like my integration with stamps.com is having issues. I am looking at the issue now.

Click the link to add information to this solution:
For some reason your system via USPS will not allow my address? It is the same one you have shipped to in the past. Jerrold Stevens 1684 NW Bonney Dr Corvallis Or, 97330-9159 US 503 374 5680

1, 2, and 3 will be used. They connect to the U, V and W connections on the VFD. I would actually use a shielded cable as this cable is used with motor coils and will definitely send off EMF. Connect the shield to the earth ground terminal in the VFD.

If the spindle spins in the wrong direction than expected, just swap two of the U, V, W wires on the VFD. It doesn't matter which two of the three wires.

Click the link to add information to this solution:
The pin configuration on my spindle’s connector. It is not clear what number references which pin.

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Make sure that the spindle motor output pin is not interfering with the signal. Go to config -> ports and pins -> motor outputs, at the bottom of the table, there will be a line for spindle. Make sure that spindle line item is disabled.

Additional Information:
I disabled the spindle port and I am still only able to activate port 3 and get 24v and even there when I enter m5 the voltage bounces all over the place. The other outputs read all over the place whether they have been designated as the spindle on the spindle settings tab

Additional Information:
I tried wiring a relay to each of the outputs and only out3 was able to activate the relay

Click the link to add information to this solution:
[575] I connected this to 24v power supply and only out3 will show 24v when activated the other 3 read 300+v whether activated or not

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

The parallel breakout board uses pins 10 to 13 relating specifically to the pin numbers on the parallel port. It is in fact 13 and not i3.

The mach3 USB board does use the I1-I4 using the I to represent the word "input"; hence I3 (i3).

Thanks for the question and wanting clarification.

Click the link to add information to this solution:
In the video 'Primer on Homing and the Use of Limit Switches' Patrick refers to pin number "13". Is this in fact pin "i3"?

From our records, you ordered Mach3. We purchase the license from the software developer and then we email you the license file that will be copied into your Mach3 installation.

Make sure to install Mach3 while you wait for the license file to be emailed to you.

Click the link to add information to this solution:
l I know when my item has been shipped? I ordered it under guest check out, I’ve called the number 4 times and no answer! The email I received said it will arrive by email?