Have you tried comparing all of the parameters for the motor outputs? For instance, go into the motor outputs screen in the mill profile, take note of all the parameters. Then open the turn profile, go into the motor outputs and change the parameters from the notes you had in the mill profile.

If that works, do the same for the other setting screens.

Click the link to add information to this solution:
[575] Everything works in mill, but if I wanna use turn software then there is problems to recognize rnrmotion card.

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

Can you add more information. I am not familiar with LCD and -1 as serial number.

Click the link to add information to this solution:
Device states serial number is -1. I did the LCD bridging from 1 to 3 and it will not allow me to recover it.

Yes, you can use one of the onboard relays on the pokeys57CNC controller to trigger your plasma torch as long as your plasma has dedicated wires to triggering the plasma torch.

Click the link to add information to this solution:
[596] Will I be able to fire a plasma torch directly off of this board or will I need a torch relay. If so, can you recommend any?

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

Yes, you can use the Autodesk123D CNC Utility found here: http://www.123dapp.com/aboutcnc

This utility will work with any standard CNC machine. Our machines use standard electronics and you choose the software that controls the CNC machine.

Click the link to add information to this solution:
If I buy the Combo #1 with hardware, plans for $255.00 and get all the required parts, will i be able to use with Autodesk 123D?

Yes, you can use a conductive metal to serve as a zeroing block for the Z axis. All you need to do is connect the block (conductive metal) to one of the 4 inputs on the controller. The end mill must be connected to the DCM terminal (the GND of the 24V power supply) of the controller. In the inputs dialog box (config-ports and pins-inputs). Under the probe line, enter port 3 and the pin used for the block.

Click the link to add information to this solution:
[575] Hi can I use a zeroing block with mock three interface board and do you have one I can purchase and directions on how to set up

Sure, come on by! You can come and see some of our machines in action; pose difficult questions and hopefully we can answer them; and even have some tests done with stuff you bring.

Click the link to add information to this solution:
I am in Houston. I will use this to make cabinets. Do you have a location I could see one in use cutting similar products?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

Try the probe connected between the input and DCM with just wires connected to those terminals. When you short the two wires, you should see the change in the diagnostic screen.

Make sure that the probe configuration is correct:
Config -> ports and pins -> inputs tab
on the probe line, make sure the pin number matches the IN number on the controller. Make sure that the port number is 3. And finally, make sure the active low is set correctly. Toggle the active low to toggle the normally open and normally closed state of the probe.

Additional Information:
Nothing changes in the diagnostic screen, however the Digitize led is lit. One wire on in4 the other on DCM. If I were to put a multi-meter to any of the pins would there show any voltage?

Click the link to add information to this solution:
[575] I have my probe conected and have checked continuity but my probe does not show to be working. What else could be wrong?

You should not have a problem with using this controller and having more than 500 lines of GCode. The 500-lines limitation is specific to licensing. Make sure that the Mach3 that you are using does not show "Demo" at the top of the screen. You can also confirm this in the help->about. If you are using a license that was purchased through this website, or from Machsupport.com, you should be fine.

Additional Information:
i have a licence but mach 3 not work above the 500 lines

Click the link to add information to this solution:
[575] Although i have licensed mach, when i use that particular board it seems to run only 500 lines of code, how can i fix that? i

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

We have sent machines everywhere across the globe and we can work with freight companies to get you a good rate on a shipment. Please email sales@buildyourcnc.com to request a quote.

Click the link to add information to this solution:
Im from chile have you ever send any machine to south america? can i buy only the mechanic and electronic things ( wood parts are much weight)

Yes, we can create an only wood kit for you. Please give us a call on Monday to provide your name so we can look it up in our system to confirm your previous purchase and we will provide a PayPal invoice for the kit, since this is a special case.

Click the link to add information to this solution:
Is it possible to purchase the wood pieces only for a BlackToe 2.0/2.1? I have all of the hardware from my kit, but the wood pieces were lost in a recent move.

If you are getting the message RNR Motion Card Not Found, the controller is shorting. Check the wiring to make sure you have all of the correct wires in the correct terminals. Check the voltages of all the terminals to make sure everything shows the correct polarity and voltages.

Additional Information:
Mine did the same thing. Try pushing the USB cable all the way into the port and slightly up. My usb port on the card is slightly oversized and breaking the connection. Ordering some USB type B connectors off of amazon, gonna try and re-solder a new port on the card before replacing the card.

Additional Information:


Additional Information:
I am having the same problem but nothing has fixed it. I have replaced the card but still no results.


Additional Information:
I am having the same problem but nothing has fixed it. I have replaced the card but still no results.

Click the link to add information to this solution:
[575] After reset of E stop, I get error message "RnR Motion Card Not Found". Have you any advice?

It appears that the LCD that you have on the vacuum pressure controller is damaged. You will need to remove the LCD (desolder the LCD) that is on the controller and resolder a new one.

Here is a link to the LCD used for that vacuum pressure controller:
https://newbiehack.com/categories/newbiehack-LCD_Displays_and_LEDs-LCD-16x2

Newbiehack is a sister website to buildyourcnc.

Click the link to add information to this solution:
I have a vacuum regulator pump controller that I purchased from you previously. The LCD display is now missing the bottom line of text. Have you run into this issue before? Can I just swap out the LCD displays or is a fix going to be more involved?

When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
I AM HAVING TROUBLES FINDING THE PD PROGRAM, HAVE BUT IT DOESN'T SHOW EVERYTHING NEED TO PROGRAM MY VFD. ANY HELP WILL BE APPRECIATED...

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
[575] Is there a way to use an X,Y plate that will only be responsible for corner finding?