Make sure that the port setting for that output is set to port 3. To do this in Mach3, click config -> Ports & Pins -> click the outputs tab and in the list of outputs, select the output you want to use and set the port to 3.

Click the link to add information to this solution:
I have a single axis motion for my table saw fence. Motor, limit switches and e-stop work fine. I now need to add an air solenoid relay but I cannot get the outputs to work. I have 24v supply connected and tried using the Spindle output on pin 1. But using a multimeter, there is no voltage on the Output 1 terminal.

The outputs are independent of the PWM function of the controller. The PWM uses the ACM and AVI outputs from the controller to the VFD along with the 10V input from the VFD to the controller. The 10V input serves as an upper voltage reference for the PWM output. The PWM output is discrete and does not connect with the ON/OFF outputs 1-4 terminals. Did you try testing the outputs without using the AVI and ACM PWM function?

Click the link to add information to this solution:
[575] Depending on the command I use (M3 S50, M3 S100, M3 S70) at a pmw base 100, Ill get not just output 1 with 24v, also outputs 2 3 or 4. Tested on 2 different boards and I just can't find the problem; at the configuration there is only output 1 enabled (port 3 pin1)

Have you tried a different input pin?

Customer response:
I've tried all pins: 10, 11, 12, and 13. I get the same non-response in each case.

Recommended action
There may be a problem with the board. If you are using our parallel breakout board, we can ship you a replacement (call us), otherwise, you will need to determine the problem with the vendor of the breakout board you are using.

Additional Information:
I have tried 3 different breakout boards from 3 different providers and they all do the same thing My limit switches are microswitches wired NC with each axis wired to the BO Board. I have checked each circuit and all is OK to the BO board. each circuit has continuity at the board and when any switch is pressed the circuit breaks. Mach 3 does not recognise that the switches are even there. They are configured as active low Do you have a suggestion.

Additional Information:

Click the link to add information to this solution:
I'm having trouble getting Mach3 to recognize my limit switches. I've eliminated everything back to the breakout board. I can directly connect Input 10 to GND on the breakout board while Mach3 is in autorecognize mode and Mach3 doesn't acknowledge anything.

Did you get a manual for your VFD? Where did you purchase the VFD and spindle?

Additional Information:
I bought the VFD through Amazon with a similar spindle that you sell. The VFD came with a manual but unfortunately the spindle had all the model number and specs scratched off of it. In an attempt to set it up, I fried the spindle. I have complained to the vendor and to Amazon but have received no solution. If your spindle arrives with proper documentation I probably can set it up myself.

Click the link to add information to this solution:
What are the configuration settings for VFD for Spindle 1.5kW 110V. The search settings have a link for a 2.2kw spindle so I'm afraid they are the wrong ones and I don't want to fry the spindle. My VFD is an Huanyang HY01D511B.

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

Yes, the RNRMotion.dll file must be used and put in the plugins folder under the Mach3 folder.

The XML file that I link on the Mach3 USB controller page is the file you should start with. This file will have the necessary configuration that links the Mach3 USB controller to the Mach3 control software. You can then make whatever changes you need to this configuration to tailor it to your machine.

Do you see a quick flashing red led on the board when you press the arrow keys?

Additional Information:

Click the link to add information to this solution:
[575] Do I have to use the motion driver and configuration file to use this card? The x,y,a shows that it's moving on display, but the motors aren't moving.

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

Yes. The VFD (Variable Frequency Drive) has a large set of parameters that can be modified. This is typically called "programming" the VFD. The parameters can be accessed using the front control panel of the VFD.

Since the VFD is the mechanism that control the allowable current draw from the spindle, there is a parameter that assigns the motor rated current; however, it is probably better to match the rated current of the motor and "up" the circuit breaker current instead. If the current limit is set too low, then there is a possibility that the spindle will cause a current overload error on the VFD and cause the spindle to stop.

Click the link to add information to this solution:
With your 120v drive systems for your 2.2kw spindles, do you do something to limit the output to the spindle so that the current draw doesn't exceed the 80% limitations of a 20a circuit? I have a dedicated circuit for my router and I am considering a spindle upgrade, but I am curious how the configuration matches the math.

Youmay be able to find an adapter for your cable, or even a new cable, locally. This is the cable we sell that will work, https://www.buildyourcnc.com/item/electronicsAndMotors-cable-wire-db25-male-male

Click the link to add information to this solution:
The female 25 pin socket on my computer has to be connected to a similar socket on the breakout (parallel) board which came with my Blacktooth. Do I need a DB25 to DB25 cable, if such a thing exists? The cable I have is male to female.

You may need to add the m7 or m8 code to turn on the coolant or mist and m9 to turn it off. I will look further into this to see if mach3 can turn on the coolant when the spindle is turned off. I believe the coolant is a separate function from the spindle control since you may not need coolant for every material that you will be milling.

Additional Information:


Additional Information:
I have tried typing M7 and M8 into the MDI with no success. I can toggle the coolant on and off using the flood control button. Water flows and the LED lights on the diagnostic page. I followed the setup instructions in the video on the Pokeys57CNC page, which includes the spindle setup page. Those videos are very helpful.

Additional Information:
To close this question - The M7 M8 commands did start working. I never figured out why they would not work before. I still cannot get the coolant to turn on with the spindle from the Mach3 set up. I have given up and just make sure the M command is in the g code.

Additional Information:

Click the link to add information to this solution:
I can turn the flood coolant on using the toogle in Mach3 so Mach3 is talking to the PokeysCNC board (using output3). In spindle setup, Output3 is assigned to flood and the disable box is not checked. Output 3 is enabled and assigned to the correct relay. However, coolant does not come on when the spindle is turned on. Any suggestions about what I am doing wrong would be appreciated.

Do you have an oscilloscope? You will be able to see the PWM signal and determine if the output is correct. Make sure that you are using the 10V from the VFD as the voltage reference for the 10V terminal on the Mach3 USB controller. The 10V terminal is an input, not an output on the Mach3 USB controller. The 10V is the top voltage signal level that the Mach3 USB controller uses for the PWM signals 100% duty cycle.

Click the link to add information to this solution:
[575] I have the wiring and programming and parameters set the same way that you do in the spindle speed control and outputs videos, I can start and stop the spindle with mach3 but can't seem to control the speed. Can you think of solutions?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

For setting up home proximity sensors on the PoKeys57 board, it's typically recommended to use the designated limit/home terminal or pin. This is because these ports are specifically designed for connecting limit switches or proximity sensors used for homing.

If you've already connected your sensors to the limit/home terminal and they're not functioning properly, here are a few troubleshooting steps you might want to consider:

Check Wiring and Connections: Ensure that the wiring to the sensors is correct and secure. Sometimes a loose connection can cause issues.

Sensor Configuration: Verify that the sensors are properly configured in the software you're using to interface with the PoKeys57 board. This could involve setting the correct sensor type (NPN or PNP), and ensuring the software is looking for the homing signal on the correct pins.

Test Sensors Individually: Disconnect other inputs and test each sensor individually to isolate the issue. This can help determine if the problem is with a specific sensor or the board itself.

Firmware and Software Updates: Ensure that your PoKeys57 board firmware is up to date, and that you're using the latest version of the control software.

Click the link to add information to this solution:
On the pokeys57 board should I use the limit/home plug or just the block next to that plug form setting up home proximity sensors? I have them on the plug now and can not get them to work.

What are the voltage requirements for your proximity switches?

Click the link to add information to this solution:
On the pokeys57 board should I use the limit/home plug or just the block next to that plug form setting up home proximity sensors? I have them on the plug now and can not get them to work.

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

I have not come across this problem, but there may be USB, or firmware issues that you are experiencing. I would recommend going on the polabs website and using their support center (https://support.poscope.com/)and posing that question to them. Also, have you tried the ethernet port as an alternative to see if that helps?

Here is the response from an LLM:

Check USB Cable and Port: Start with the basics. Sometimes this error is due to a poor USB connection. Ensure you're using a high-quality, shielded USB cable and that it's plugged into a USB port directly on your computer, not through a hub. If possible, try a different USB port or a different cable to rule out any issues there.

Update Firmware and Software: Ensure that both your PoKeys57CNC firmware and the Mach4 software are up to date. Firmware updates for your PoKeys board might include optimizations or fixes that address connectivity issues.

USB Polling Rate: This error can also arise from the USB polling rate setting in the PoKeys configuration software. It might be set too high for your system's ability to handle it. Try lowering the polling rate and see if that resolves the error.

Computer Performance: Check your computer’s performance. If it’s running several heavy applications simultaneously, it might not be able to process signals from the PoKeys board fast enough. Try closing unnecessary applications or consider using a dedicated machine if your current setup is too taxed.

Mach 4 and PoKeys Plugin Configuration: Dive into the Mach 4 plugin configuration for PoKeys. Ensure that all settings are correctly configured as per the manual. Incorrect settings might lead to communication bottlenecks.

Connection Quality and Interference: Consider any potential interference sources near your CNC setup or computer. Electromagnetic interference from large motors, other electronics, or long cable runs can affect communication quality. Try rearranging your setup to minimize interference.

Consult Documentation and Support: If the issue persists, consult the detailed documentation provided by PoKeys or reach out to their customer support. They can offer more specific advice based on the latest product updates or known issues.

Click the link to add information to this solution:
[596] I have followed your YouTube video on setting up the pokeys 57cnc board but when I open Mach 4 I get a error message the the connection is to slow

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hello, we are trying to assemble a kit and the breakout board rev 2.1 that we have does not match the video... we do not see where to connect the 5v powersource to finish step #3, can you provide a location for the power hookup for our board.

I have not come across this problem, but there may be USB, or firmware issues that you are experiencing. I would recommend going on the polabs website and using their support center (https://support.poscope.com/)and posing that question to them. Also, have you tried the ethernet port as an alternative to see if that helps?

Here is the response from an LLM:

Check USB Cable and Port: Start with the basics. Sometimes this error is due to a poor USB connection. Ensure you're using a high-quality, shielded USB cable and that it's plugged into a USB port directly on your computer, not through a hub. If possible, try a different USB port or a different cable to rule out any issues there.

Update Firmware and Software: Ensure that both your PoKeys57CNC firmware and the Mach4 software are up to date. Firmware updates for your PoKeys board might include optimizations or fixes that address connectivity issues.

USB Polling Rate: This error can also arise from the USB polling rate setting in the PoKeys configuration software. It might be set too high for your system's ability to handle it. Try lowering the polling rate and see if that resolves the error.

Computer Performance: Check your computer’s performance. If it’s running several heavy applications simultaneously, it might not be able to process signals from the PoKeys board fast enough. Try closing unnecessary applications or consider using a dedicated machine if your current setup is too taxed.

Mach 4 and PoKeys Plugin Configuration: Dive into the Mach 4 plugin configuration for PoKeys. Ensure that all settings are correctly configured as per the manual. Incorrect settings might lead to communication bottlenecks.

Connection Quality and Interference: Consider any potential interference sources near your CNC setup or computer. Electromagnetic interference from large motors, other electronics, or long cable runs can affect communication quality. Try rearranging your setup to minimize interference.

Consult Documentation and Support: If the issue persists, consult the detailed documentation provided by PoKeys or reach out to their customer support. They can offer more specific advice based on the latest product updates or known issues.

Click the link to add information to this solution:
I HAVE FOLLOWED YOUR YOUTUBE VIDEO ON SETTING UP THE POKEYS 57CNC BOARD BUT WHEN OPEN MACH 4 GET A ERROR MESSAGE CONNECTION IS TO SLOW

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I have a 2000 WK 11–3 Z limit switches going to A c10r10 breakout board . Can I also use them as my home position as well. I need The wiring configuration