Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Most likely, the driver is not receiving the high or low signal for the direction terminals. The way direction works for an axis is the controller will output a high signal (5V) for one direction and low signal (0V) for the opposite direction. If the signal is always at one signal, say 5V, whether it is commanded in one direction or the other, then the axis will only move in that direction.

To solve this problem, make sure that the wiring is secure at both ends (from the controller to the driver). Also, make sure the Dir+ and DIR- are both wired correctly (i.e. the Dir- is connected to the signal gnd on the controller and the ZD is connected to Dir+ on the driver.

You can use a multimeter to determine the voltage at the ZD terminal by:
- setting the multimeter to DC voltage (the V with a straight line, or dashed line above the V)
- place the black lead on the gnd terminal
- place the red lead on the ZD terminal
- press the page up button and check the voltage
- press the page down button and check the voltage.

You should see the voltage change from 0V to 5V or vice versa.

Click the link to add information to this solution:
Hi I have just set up my machine using a mach 3 USB board I can only get the Z to go in one direction Y and X are Ok I have check wiring and looked at video over and over what have I missed??

Did you set them up as limit switches or home switches?

Additional Information:
Not sure where do I check that?

Additional Information:
Go to config, then ports and pins, then input signals.

Additional Information:
The limits are labeled x++, x— for example.

Click the link to add information to this solution:
I'm using Mach3. I have 2 limit switches on X, 2 on Y and 1on Z for retracted/home. I can go to diagnostics and see the switches/inputs working. But when I move with jog or gcode they have no effect. Also I can go right past the soft limits. I must have something turn off but I don't know what.

The Mach3 USB interface board will require a 24V power supply to enable the use of the input, output terminals, and the spindle VFD 0-10V and output for speed control.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.

If you have the laser firing using the Z direction, then you want to make sure that the thickness and clearance plane is extremely small. The time it takes for the software to think that the z axis has lowered to the depth set in the design is causing the laser to stay on in a single position for too long. Make sure that the depth is extremely small, like .0001" or the smallest amount allowed by the Vectric software. Also, make sure the clearance plane (the height that the z axis would raise to clear any protrusions like clamps and the such) is extremely low.

Click the link to add information to this solution:
I have been using a Blacktooth for some time, with Vectric2d and Mach3. I have always found that the laser burns a hole before moving off. I have always set material thickness at actual value. Should it be set very low? Also, of the many post processors supplied with 2d, which is best for Blacktooth?

Do both motors, the main and slave work correctly when using the arrow keys?

Click the link to add information to this solution:
How do you slave an axis with mach3 and pokeys57cnc? My slave axis is only going one direction as a slave and goes correctly in both directions when I direct it with an xbox controller.

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

You can use the Pokeys57CNC board with our 3.0 amp drivers. The Pokeys57CNC has all of the headers necessary to provide the pulse train to any common stepper driver.

Here is the link to the Pokeys57CNC interface board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Here is the link to the 3.0 amp stepper motor driver:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

Click the link to add information to this solution:
I'm planning on using your 425 oz motors and need help on selecting the right interface and driver boards. The PoKeys57 CNC USB card looks good but I wonder if the 2.5 amp driver boards shown with it are enough for the 3 amp motors?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

The e-stop should be wired like a limit switch and can also be within the same limit switch circuit. Use one of the input pins to create the e-stop circuit.

1. Run a wire from the input pin terminal to the e-stop switch red side (one of the two terminals on the red side). The red side is NC (Normally Closed).

2. Run a wire from the other side of the red side of the e-stop switch back to the gnd terminal (or to the next switch - limit switch, NC terminal, then back to gnd, or to the next NC terminal of the next switch, do you see a recursive pattern here?).

The wire that you use for the connections should be shielded and the shielding and any other loose wire within the cable should be tied to gnd.

Click the link to add information to this solution:
Hi - I have wired in a breakout board (with relay) as per suggested wiring instructions (black toe 2X4). I want to wire in an estop but need some guidance on wiring. Also Mach3 is requesting I reset the estop, which suggests its expecting one? Can anyone help? Thanks. Miles

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

You will want to connect the homing switches (which may also serve as your near limit switches) to different input terminals. It's ok to add more limit switches with the home switches, but each home should be on independent inputs. For example, connect home X and any other limit switch to IN1, connect home Y and any other limit switch to IN2, and so on. This will allow you to properly use the "ref all home" button in Mach3.

Additional Information:


Additional Information:
In the instructions (diagram 1) you show all the home switches connected in parallel? But here you say they need to each have their own inputs. "You will want to connect the homing switches (which may also serve as your near limit switches) to different input terminals." I dont see how the second and third axis can go home if the first axis has already closed the parallel circuit unless they back off a bit until the switch opens up again before the next axis goes to home? My machine has no limit switches so I assume they are home switches.

Click the link to add information to this solution:
[575] I have finally got my limit switches wired and working - thank you. Can they also used as homing switches and if so it it just a question of looping the two inputs on the board i.e. the limit and home terminals IN2 to IN3

You will also need to check if the mach3 configuration and the wiring. Since you tested the connection from the motors to the drivers, the connection from the computer to the interface may still be the issue. It could also be the connection from the interface to the drivers, but we test all of these units going out, so I don't believe that would be the problem.

If you have a redfly that uses a parallel cable, you may need to check to make sure the parallel cable is functioning properly, and also, make sure that the interface is also powered using a usb cable.

If you have a usb interface (the terminals will be labeled XD, XP and so on), then there may be a wire not seated correctly in a terminal.

Click the link to add information to this solution:
I plug in my redFly for the first time and after configuring Mach3 and rechecked my settings axes Y and Z are working well, but X is not working, just for testing I plugged in each motor to the Y and Z and they work fine, but no motor works when plug into the X axes of the redFly, also one of the NEMA 24 425 Oz motors dose not turn just jitters.

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?

We have ran across this issue on occasion, and usually results is there is something along your wiring that is causing a fault or is not getting good contact.
We would recommend going through the wiring thoroughly and checking continuity with the y-axis wires, going from your USB or Parallel BoB to the driver.

Click the link to add information to this solution:
My CNC machine has suddenly started going in only one direction in the Y axis. It was working fine for several days and then started going in a single direction when I would do a manual job.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

If you already have a Mach3 license, you don't need to purchase another one. The license is connected to you rather than the computer. Mach4 is licensed to the computer, but you are able to have multiple computers for each license, and can be switched from one computer to another.

If you purchased the license from me, you can call (make sure to leave a voicemail), or email to get a re-issued license.

Click the link to add information to this solution:
[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine. I will have to buy a new license for the Mach 3 so will need to get the interface board I have to talk to MAch 3. Can I get just the disc or is there a place I can download what I need?