Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I have intention of purchasing your 1/2 inch precision lead screw set to build my CNC machine, could I have the schematic dimension of your 1/2 inch anti-backlash nut, bearing for the lead screw and the shim? Also is your 2.2kW spindle able to mill Aluminum and what is the accuracy?

Make sure that the port setting for that output is set to port 3. To do this in Mach3, click config -> Ports & Pins -> click the outputs tab and in the list of outputs, select the output you want to use and set the port to 3.

Click the link to add information to this solution:
I have a single axis motion for my table saw fence. Motor, limit switches and e-stop work fine. I now need to add an air solenoid relay but I cannot get the outputs to work. I have 24v supply connected and tried using the Spindle output on pin 1. But using a multimeter, there is no voltage on the Output 1 terminal.

Just specify the full length in the quantity field in the shopping cart and give us a call to inform us of the cut lengths (you can also email customer service - link in the contact us page - link at the footer). We are working on a way to do this at the product page, but won't be finished for a few more days.

Additional Information:
20

Click the link to add information to this solution:
How do I order 3 specific lengths of lead screws in one order? I could only order a single total amount via the shopping process. I require 36", 60" and 14". If I order 110", I will get 79" + 31". Do I have to order 115" and pay for an extra 5" to get around this?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

If you are wanting to use servos, I would highly recommend using closed loop steppers and drivers. You will get the best features of both the servo closed loop and the exact digital positioning of stepper motors.

For controllers: the pokeys57cnc will work with either Mach3 or Mach4
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Otherwise, you can use the Mach3 USB controller if you only an on using Mach3:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
Hi there. I have an ex school Boxford HSRmi2 sat in my workshop, good condition and I'm assured it's all ok, but I want to rip everything out and go down the Mach 3/4 rabbit hole with servos. I need help at this point as I haven't done anything like this before and have no knowledge of controllers/motors etc. Could someone please point me in the right direction? Thanks.

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.

If you need to create a laser engraving system that engraves on a large rotating drum. You will need the motors, drivers, laser control system, laser tube, power supply for the laser and motion drives, and the mechanical and structural components to turn the drum (X axis) and move the y axis.

Click the link to add information to this solution:
I wish to laser engrave wood drum shells. (musical instrument) A X axis with a 3 roller system, 2 passive inside the cylindrical shell, one driven to move the shell around it's circumference would suit my needs. I have 20 design engineering in my past, I could design up what I need in Autocad but have no idea how to automate the system and make it work. college was 20 years ago lol! Help!

Yes, you can purchase the blackToe 2'x4' CNC machine kit without the optional table.
https://buildyourcnc.com/Item/cnc-machine-blacktoe-v4-2x4

The 4th axis product can be found here:
https://buildyourcnc.com/item/axes-4th

We recommend Mach3 or LinuxCNC to control the machine:
https://buildyourcnc.com/item/control-SOFTWARE-mach3
https://buildyourcnc.com/item/control-SOFTWARE-linuxcnc

When you go to the cart to check out, the shipping prices will be displayed when you click on the calculate shipping button.

The instructions to assemble the machine is on the product pages of the machine and parts you purchase. See above links.

Click the link to add information to this solution:
hello, is it possible to send all components of a 4Axis CNC in size of ( about 2' x 5' ) to Iran country without table and all required manuals and measurements to create and assemble cnc machine and table plus required software? i need total price for this request if it's possible for transfer.

It is most common for the laser tube to go out, after about 1000 hours of work time!
It is strange that the new laser tube will not fire!
We would recommend to check the tungsten leads, if they are making good contact!

Also here is a link to a instructables page where they have tested a laser power supply!
http://www.instructables.com/id/How-to-test-and-set-a-Chinese-China-made-CO2-Laser/?ALLSTEPS

Click the link to add information to this solution:
Hello - I have had some years of good use from my Blacktooth CN Laser, but had to reduce the speed on jobs over the last year to get satisfactory cutting. Recently, on a long job, the laser beam weakened and disappeared entirely over about 30 seconds (guess). I fixed a new tube, but this won't fire either. How can I safely test the output lead to see if it's dead or partially so?

Dealing with a 4' x 12' machine, our blackFoot kit will be your best option. Since our machines are only limited to the width but not length wise, you can add however much extra rail and roller chain to accommodate your extended length. Now adding our 4th axis kit (https://www.buildyourcnc.com/item/axes-4th) will be needed for your 4th axis (unless custom design is required).

These items will be the best requirements to build a 4' x 12' 4th axis machine.
Machine (either parallel/USB BoB): https://www.buildyourcnc.com/blackFoot48v40.aspx
4th axis: https://www.buildyourcnc.com/item/axes-4th

Click the link to add information to this solution:
I am looking to set up a long table, 4 x 12 foot I would need to cut wood of modest density less than 1 inch thick, and I would also need to bevel some of the cuts, so I think this is a four axis unit. Which of your kits plus upgrades would make sense? I am very capable of assembly of a bunch of boxes full of parts.

We accept many forms of payment, but online, we accept major credit cards (Discover, Visa, MasterCard and American Express) in addition to checking out with Paypal. Depending on what is ordered, a machine vs. a la cart parts, will arrive at your destination according to the shipping method chosen. A machine may take an extra week to be delivered.

Once paid, there are no changes in the amount for the purchase.

Click the link to add information to this solution:
good day I have my list of products in the cart, and before making the purchase need to ask 1. I need to know if I can pay by bank card HSBC Visa 2. If I pay today, As approximate time come to Mexico City? 3. Ordered the shipping information online, and I chose standard UPS. There may be changes in the amount? Thank you

We can lower the price for just the hardware and also for the structure. However we do not have any files, dimensions, for public access.

Additional Information:
Would there be any/enough measurement or info on the instructions to extrapolate the dimensions? What would the new pricing be?

Click the link to add information to this solution:
Is there any way to bring the cost of https://www.buildyourcnc.com/item/cnc-machine-blacktooth-laser-cutter-engraver-40w down if I only need the hardware and components, not the body? I have a cnc waterjet and could cut these parts if dimensions were provided.

Do you believe the source backlash is at the nut, or somewhere else?

Click the link to add information to this solution:
Hi Guys, I fitted new ball screws to my mill as part of a cnc conversion. I have about 0.15mm backlash in both the x and y axis. What would you recommend to remove the remainder of the backlash mechanically? Thanks in advance.

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
I need your assistance... I have two items left to setup on my Pokey57CNC and Mach4, Home switches and Spindle Speed. I have watched the videos, but they are for Mach3 and the screens are different in Mach4. Can someone please explain the setup of these two items in Mach4?