It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

Each home switch needs to be on a separate input on the Mach3 USB controller. For instance, the x-home on IN1, Y-home on IN2, and Z-home on IN3. You can still wire the other switches on the same input, for instance, the IN can contain the X-home and X++ limit. The X, Y, and Z homes can still serve as the limit --.

Additional Information:
So I need 3 of 4 INs only for the home switches??? The remaining one for ++? What about E-Stop and Probe?

Additional Information:
Please have a look at the wiring diagram you show below. There are all limit switches at IN2 and all home switches at IN3. Makes sense to me.

Click the link to add information to this solution:
[575] I have two limit switches for X, Y and Z axes connected to only one input terminal. As usual, I also want to use them as home switches. But after the first axis touches its home switch, I get an emergency stop because of "activating a limit switch". Mach 3 normally knows when to use a limit switch for homing. Which detail in the depths of Mach 3 did I forget?

You can actually select many places for the switches, depending on where you think your zero will be. I will take pictures of where we positioned our switches. We set the positions so the zero is at the bottom left corner of the machine.

Additional Information:
I will take pictures tomorrow.

Additional Information:
Thank you. Just want to finish before the holiday.

Additional Information:
Not a problem at all and my apologies for not having that information. I have been meaning to put up a video on the limit switch connection as it is somewhat difficult to explain the process in words and diagrams.

Additional Information:
Any update?

Additional Information:
I plan on driving to the office later today and take pictures.

Additional Information:
Thank you. I've just done almost everything else. Just waiting for the grade 3 grease in the mail. Also, where do you suggest connecting the cable carriers? I ran everything through the top but the carrier is getting kind of full. Because of that, it is pushing the belt out when the gantry moves.

Additional Information:
I will take pictures of those connections as well.

Additional Information:
Much appreciated.

Additional Information:
It’s my pleasure.

Additional Information:
I’m almost to the office. I’ve been shuttling my kids around today. Sorry for the wait.

Additional Information:
I’m adding the images to the end of the VLXL instructions.

Additional Information:
The limit switch connections use the NO (Normally Open) terminals. That means that the switch, when not engaged, is normally open (no connection between the com and the NO terminal). When the switch is engaged, then the connection is closed and the NO and COM terminal become connected, making a circuit.

Additional Information:
Did you bend the arm on the x switch? Or can you mount it flush with enough give to trigger? Same on both sides?


Additional Information:
It does look like it is bent in the picture. No, you do not need to bend the arm of the rotary switch.

Additional Information:
We only have the rotary switch on one side.

Click the link to add information to this solution:
How do I wire the limit switches on the VLXL? Also, where do I place them? You included 2 rotary and two other limit switches.

If you are using Mach3, the setting for the input pin 10 may be enabled as a default for use with the Emergency Stop. If there is no emergency stop on that pin, the reset will trip every time.

Click the link to add information to this solution:
I have the redleaf system for my black toe machine I have wired my limit switches in series NC after setting up in mach 3 I still get limit switch tripped after apply and ok setup can only run if I disable what am I doing wrong

Yes, the Mach3 USB board has two terminals that require 24V connection. Most VFDs have a 24V output that can be used to power this part of the Mach3 USB board.

The V+ and V- on the Mach3 USB is not absolutely necessary to operate the CNC machine/router. The V+ and V- of the Mach3 USB board powers the outputs, inputs, and spindle's speed and control.

Here is the Mach3 USB link for more information:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The new YL600 VFD we have in stock may not have this 24V output. There is a 12V terminal, but I have not tested that terminal if it outputs 12V, or if it is a 12V input. If you are only conecting limit switches to the Mach3 USB and need to power that portion, 12V will be sufficient.

I will delve into these aspects in far more detail on video.

Thanks and Merry Christmas to you as well!

Click the link to add information to this solution:
Hey Guys, I have a brand new redleaf and 5x. In the final stages of wiring and wondering a few things. Can I connect the Mach3 USB board V+ V- to my frequency inverter (type YL600-2s-2k20)? If so where? Will your upcoming (part 2)video deal with this as well as final connections for limit switches and stop button? Merry Christmas!

Yes, the best way to attach a relay to the output of the Mach3 USB board is to use an SSR (Solid State Relay) at the 24 Volt rating. This is the standard supply for this side of the Mach3 USB board.

Click the link to add information to this solution:
I am converting from a Parallel Port to the Mach3 USB. My limit switches can accomodate up to 5VDC and I want to Drive a Relay from one of the outputs. Will my switches work and do I need a 24VDC Relay?

The RNRMotion driver will not conflict with the mach3 license. Make sure you have the RNRmotion driver in the plugins folder and the provided xml in the main mach3 folder. Also, make sure to have the mach3 license file in the mach3 folder. If you still experience problems, please give us a call.

Click the link to add information to this solution:
i purchased a breakout board from you guy and the rnr motion control is messing with my license in mach 3 tech support at mach said it is the rnr software i need help to contact them and let them see what they can do to help

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

The hookup wires you will need is 22 to 24 AWG stranded and shielded for the wiring of the limit switches and E_Stop. Our kit customers select various places for these switches, so we don't supply the wiring. If you don't use shielded cable, you will need to change the debounce setting in Mach3 (if that is the control program you are using).

We typically use 14 AWG stranded wire for the VFD to Spindle (U, V, W) connections.

Click the link to add information to this solution:
I recently received missing stop button and limit switches in my 5x kit. Thank you. Is there suppose to be any bulk wiring in kit for limit switches and 2.2 spindle? If not could you please describe correct gauge wire for both? Cheers.

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

Connecting the limit switches on the redLeaf use the input pins on the parallel breakout board. Here is a link to the wiring diagram for that parallel breakout board.

https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The connection is simple. Just create a circuit from ground to the pin. When the pin is engaged, the circuit is closed (using normally open on the switch). Use mach3's autoset to automatically set the pin for the limit or home setting.

Click the link to add information to this solution:
Do you guys have any videos showing how to connect limit switches to a redleaf? If not, could you please make one? I looked at the diagrams on the limit switch page but I don't understand them.

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

Make sure to wire the limit as normally open.

Click the link to add information to this solution:
[575] I had limit switches working and on input 2. Now looking at Mach 3 diagnostics, Input 2 is continuously on and triggers limit stop. I removed all input 2 so the machine can run. Rebooted all. Anyway to reset Input on card?

Are you trying to use the MPG (tab), or the keyboard for jogging the motors? You mention 0,0,0, are you trying to home the machine with the "ref all home"?

If you cannot move the motors with the keyboard, check if the jog is enabled.

Click the link to add information to this solution:
[596] I have my motors and limit switches working correctly but I am unable to get any movement from the 'jog step' so that I can set 0,0,0. What should I check

Did you set them up as limit switches or home switches?

Additional Information:
Not sure where do I check that?

Additional Information:
Go to config, then ports and pins, then input signals.

Additional Information:
The limits are labeled x++, x— for example.

Click the link to add information to this solution:
I'm using Mach3. I have 2 limit switches on X, 2 on Y and 1on Z for retracted/home. I can go to diagnostics and see the switches/inputs working. But when I move with jog or gcode they have no effect. Also I can go right past the soft limits. I must have something turn off but I don't know what.

The wire that we sell for the limit switch wiring is here: https://www.buildyourcnc.com/item/3d-printer-component-cnc-electronicsandmotors-cable-wire-3-conductor-22-awg-wrcon-cablewire3conductor22awg

This is shielded cable to make sure there isn't any external interference with sensitive components and long wires associated with limit switches. This is necessary due to the interference caused by the motors on a CNC router and the milling process.

Additional Information:
So unshielded is cool. That's what I was curious about. Cheers.

Additional Information:
Absolutely. It's really the only type of cable I would recommend for connecting limit switches.

Click the link to add information to this solution:
Do you sell 22 to 24 AWG stranded and shielded for wiring of the limit switches and E_Stop?

You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

The GND terminal can be doubled up.

Click the link to add information to this solution:
Additional to Question 3444: Additional Information: To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on? Plus, I have a SuperPID. Another pin?