We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

To select a 4 axis NEMA 17 motor and driver combination, you will need the following:

- Four (4) NEMA 17 motors: https://buildyourcnc.com/item/electronicsAndMotors-nema17-62ozin-NEWBIEHACK-motors-stepping_motor-62_ozin

- Four (4) drivers, either the 2.5A: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular or the 3.0A: https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

- One (1) Power supply, either the 24V or 36V (recommended): https://buildyourcnc.com/item/electronicsAndMotors-power-supply

- Finally, an interface is needed, either parallel, or USB. The USB works with planet-cnc software only. The parallel interface works with all major CNC control software: https://buildyourcnc.com/category/breakout

Click the link to add information to this solution:
Can you supply a quote for a 4 axis combo kit with NEMA 17 Motors

What 3d printer do you have?

Additional Information:
whiteant

Click the link to add information to this solution:
HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

If you are interested in the USB breakout board, you will need to get an independent relay board.

Click the link to add information to this solution:
HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

Yes and properly soldered.

Additional Information:
20

Click the link to add information to this solution:
DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Only the 110v Version will have any indication of voltage on it. On the side of the power supply unit that has the black terminal strip and red wire coming out of it, there will be a silver sticker on the white side of the transformer that will state 110v, if it is 110v. If there is no sticker, then it should be 220v.

Additional Information:
20

Click the link to add information to this solution:
How can i tell if my laser supply is 110 or 230 VAC? there is no marking of any kind

The recommended total length of motor cable should be 15 feet for the blueChick v4.2

Z - 6 feet
Y - 5 feet
X- 4 feet

20 AWG 4 conductor

If your drivers will be positioned farther from the machine, you may need longer cable.

Additional Information:

Click the link to add information to this solution:
WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
I've built a router frame, so I need electronics. I'm buying 2 NEMA 34s and 1 NEMA 23. Can I get a list of controller, power supply and related components so I can get them as I can afford them? Please.

Most of our power supplies allow for a 9 amp current draw.

For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

Additional Information:
What gage wire should I use from motor to driver

Additional Information:


Additional Information:

Click the link to add information to this solution:
What wire AWG can I use to connect the power supply 24v 8.3 amps

The plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
CAN YOUR PRODUCTS OF MACHINES BE USED TO CREATE PLASMA TABLE?

Unfortunately we do not have CAD models of our machines available to our customers.

Click the link to add information to this solution:
Do you have any CAD models of your products?

You can determine if the area is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

You will need the following:
- router/spindle for the machine
- computer to control the machine
- construct a table if the optional table is not purchased
- wire and cable to connect all of the electronics

Additional Information:
- software to run the gcode (purchased separately)

Click the link to add information to this solution:
DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

Yes you can. We well the ArtCAM software and modules.

Click the link to add information to this solution:
I see Artcam modules on your site, can I still get them through you?

Yes you can. We well the ArtCAM software and modules.

Click the link to add information to this solution:
I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.