¿Cuál es el número de modelo del VFD que está utilizando?

Click the link to add information to this solution:
[79] Tengo un inversor que tiene 12 voltios en vez de 10 voltios a la salida, como hago para conectarlo a al tarjeta RNRMOTION USB(roja) que tiene una entrada de 10 voltios?, muchas gracias

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet and got out of your USB controler $ 75 .Viska have linked to a video 'Party - 2.. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

To connect the stepper motor drivers to the Mach3 USB interface card, you will need to follow the wiring diagram here: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
which can be found here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board along with all of the other manuals associated with that interface card.

Please note that the DC+ and DC- on that wiring diagram (power supply to thye stepper motor drivers) is not correct. The DC- is connected to GND on the drivers and the DC+ is connected to VCC on the drivers. Typically, the DC+ on the power supply is labeled V+ and the DC- is labeled either COM or V-.

If you are having any issues with the wiring, please let me know and I will elaborate. Thanks.

Click the link to add information to this solution:
Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

You can use the Pokeys57CNC board with our 3.0 amp drivers. The Pokeys57CNC has all of the headers necessary to provide the pulse train to any common stepper driver.

Here is the link to the Pokeys57CNC interface board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Here is the link to the 3.0 amp stepper motor driver:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

Click the link to add information to this solution:
I'm planning on using your 425 oz motors and need help on selecting the right interface and driver boards. The PoKeys57 CNC USB card looks good but I wonder if the 2.5 amp driver boards shown with it are enough for the 3 amp motors?

All USB boards, are tested and checked before shipment for all axis, and inputs. Here is a link with clear instructions on how to setup Planet-CNC (http://www.planet-cnc.com/faq/machine_setup/).

Please check continuity for each individual wire and for any crossover disruption when wiring your board, try to wire each as cleanly and with out crossing any live power wires and or motor motion wires.

Click the link to add information to this solution:
Email link is not functioning. (continuation of z+ limit question) The Usb cnc controller is now switching what the limits are. IE: X- is showing up as Y+ ect. Is this a bad board? Thank you.

If your motors turn very slowly using your Mach3 USB board, then either the pulse from the board is being output at a slow rate or the motor drivers are set to a higher than expected microstepping:

The Mach3 USB board outputs the pulse rather than the computer, but Mach3 controls this pulse frequency within the motor tuning section. First, determine if the travel distance is correct with the computer and the physical travel of the machine.

If the travel is different, then your stepper motor driver's microstepping is incorrect, or the steps per inch/mm in the motor tuning within Mach3 is incorrect.

If the travel is correct, then simply change the velocity and acceleration parameters to your desired level. If Mach3 will not achieve the velocity you desire, then decrease your stepper motor driver's microstepping setting, readjust the step per inch/mm in mach3 and readjust the acceleration and velocity to your desired levels.

Additional Information:
Text is engraved in mirror image

Click the link to add information to this solution:
I have not used my CNC router (Mach3, USB interface board) for several months. When I tried to use it, all 3 stepper motors moved extremely slowly. Where should I start troubleshooting?

Yes the CNC will do 3D wood carving and we can ship to Mexico. email sales@buildyourcnc.com for more information.

Click the link to add information to this solution:
I have a New Hermes Vanguard 4000. It has an IS controler. I know nothing about these machines. What can I do to make it usable?

The PlanetCNC USB software, like most machine control software, can be used to control a laser engraver/cutter. The typical modification is to use the Z axis down signal to fire the laser, analogous to an endmill cutting into the workpiece from an initial position above it.

For the second question, it is important to note that BYCNC machines are not based on PlanetCNC software, or any other particular machine control system. The machines themselves will accept standard signals from a wide variety of machine control systems, not just PlanetCNC or Mach3. This allows maximum flexibility for the customer to choose their own preferred software for this part of the toolchain.

That said, our machines will accept a laser head either in lieu of or in addition to a spindle. Here is an example of a combination spindle/laser mount for our greenBull machine: https://buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head. We have all the parts you would need to add laser functionality to your machine here: https://buildyourcnc.com/LaserComponents.aspx, if you feel comfortable assembling your own package. Also, feel free to contact our sales department for a quote if you need a custom assembly.

Click the link to add information to this solution:
Can the Planet CNC USB controller be used with a laser engraver/cutter? Can the build your own CNC based on the Planet CNC USB controller accept a Laser head instead of a router?

The USB Interface page: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout

On this page, there is a datasheet that explains the connection schemes for the limit switches on step 1 of the instructions. The datasheet explains single and multiple switch configurations and parallel/serial connections schemes for the NO/NC (Normally Open/Normally Closed states).

If there is further information you need, please reply on this FAQ.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Please provide detailed instructions on how to connect limit switches to CNC USB BOARD. I can not find instructions anywhere. I am new to cnc world and really need help. Thanks

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?

You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

Click the link to add information to this solution:
sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

Dealing with our inverters, they are built with a bit of margin on the input power. For our 220V VFD the margin is from 170-250V 50/60Hz, so running our VFD in your location will not be an issue! Our electronics will not have a issue running at 230V as well.

Click the link to add information to this solution:
Hello. I am interested in the green bull 6X long z CNC machine with electronics. I live in NZ, where the voltage is 230 V and 50 Hz. is it going to be possible to get the inverter to run here? Thanks!

The size of the stepper motor is measured in holding torque, generally oz/in. You will determine the torque loads of your axes when selecting steppers. Once you know which stepper you need, the drivers and controller board are simple to pair with them.

Click the link to add information to this solution:
I'm trying to build my CNC router 3m*1.3m, but i'm not sure what is the type of stepper motor i should pay, all my CNC body is Al. I need to bay 4 Stepper motors, 4 drivers, spindle, inverter, and i don't know what is the type of controller ?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?