For the blackTooth laser cutter and engraver, it is not possible to lengthen within its existing enclosure dimensions. The cable management is a bit tight. Call us to discuss.

Click the link to add information to this solution:
I am interested in your laser cutter package. Can you create a machine with custom length requirements? ie. 36" length

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

The Vertical Laser XL's 80 watt CO2 laser tube is capable of cutting lighter material such as wood and plastic at up to 1/2" or 12mm.

Click the link to add information to this solution:
am interested in purchasing the 80 Watt Vertical Laser XL 4'x8' Laser Cutter and Engraver, what material depth can it cut?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

Consulting our sales dept, or employee, For a specific package that you might want to inquire about, please email customerservice@buildyourcnc.com for further assistance.

Click the link to add information to this solution:
Can I cousult with you on the cnc package I'm interested in?

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
Is the Mach3 software compatible with 3 axis motion control combo kits? The planet cnc software is mentioned as being compatible.

If you were to buy all of that, only thing you'll need is the mach3 software to run the machine.

Click the link to add information to this solution:
I am interested in purchasing the Green Lean complete kit and also buy the ArtCamPro what other software will I need to up and running?

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

If you have an existing PC with a parallel port you will not need to purchase the onboard computer system on the blackTooth laser cutter and engraver. You will want to purchase the blackTooth laser engraver that comes with the parallel interface (breakout board). If you have an existing CNC machine that is being used with this PC, you can disconnect the CNC machine and connect the blackTooth to this PC. You will want to have two configurations for your control software.

Additional Information:
We have a version of the blackTooth that is 110v and 220v. We generally determine which is sent according to the requirements of the customer and in what country they live.

Additional Information:
20

Additional Information:
Parallel Port Configuration BIOS settings and Mach 3.

Click the link to add information to this solution:
I'm interested in purchasing your black tooth laser engraver and am curious what setup to get. I already have a cnc wired via parallel port to my PC. Do I need to purchase the black tooth laser with the integrated computer or can I just disconnect my current cnc's parallel port and connect it to the black tooth laser engraver? Also is the black tooth 110v?

We have not specifically tested for this data point, but a general rule of thumb is that an 80W CO2 laser can cut wood up to about 1/2 inch. Actual results depend on a number of variables -- power level used, amount of air assist, focal length of lens, number of passes, cutting speed -- and each of those has its own tradeoffs. We are planning to do some of these tests in the near future and post the results, so stay tuned for more in depth information.

Click the link to add information to this solution:
Hi im interested in your new 4 x 8' laser , what is the thickest mdf sheet it can cut through ?

The (blackTooth) laser cutter and engraver comes with the unit shown on the product page seen here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

The unit is intended to be set on a table top.

The stand that you may have noticed was only a demonstration on how to use SketchUP in a CNC process scenario. The stand has never been offered with the blackTooth laser.

Click the link to add information to this solution:
I am interested in buying Laser Cutter/Engraver with Integrated Computer, so can you please let me know if your offer still stands?

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

Yes, you can use these electronics to move a machine that has an area of 48" x 48". If you are looking for faster jogging, you can upgrade the motor to this one: https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-1100ozin

Click the link to add information to this solution:
[50] this combo is compatible for a CNC with a 48" x 48" work area

The blackTooth machine, as it is designed cannot be modified easily as the box within which it is contained also serve as its structure. We are currently designing a special mount for the greenBull (for the 40 watt tube) which will provide 5'x10' or 6'x12' work area and the machine is far less expensive than comparable 4'x8' laser systems. We are also developing a 4'x8' 80 watt system where the tube is in the horizontal orientation. More information can be found in the R&D section.

Click the link to add information to this solution:
I am interested in getting your 40W laser system. How difficult will it be to increase the size to 48" x 48"?

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
im converting a seig x2 mini mill to cnc and I'm looking at the 4 axis cnc combo kit is it mach3 compatible? and is everything included in the kit to build a cnc control box like wires,connectors,wiring diagrams ect?

Yes, we ship to Puerto Rico.

Click the link to add information to this solution:
I am interested in making a purchase but need to know if you ship to Puerto Rico, is urgent

The weight of the 2.2kW spindle without the VFD (variable frequency drive or inverter) is 11 lbs or 5 kg.

The 2.2kW spindle with the VFD is 15 lbs or 6.8 kg.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the water cooled 2.2 KW spindle for $339, how much does it weigh?