The 2.2kW Spindle has many advantages over a standard router such as the Porter Cable. The most obvious benefit to the user is the significant reduction of both dust and noise.

Additional Information:


Additional Information:
What size water source is needed and how long can it be used before it is too warm? Do you have a pressure vs. flow curve for the spindle so I can properly size the water pump?

Additional Information:
I used a small pond pump inside a 5 gallon bucket. I put a little bit of windshield washer fluid in with it to keep anything from growing in it. It's worked great. I've had 1 hour run times with no noticeable increase in spindle temp.

Additional Information:

Click the link to add information to this solution:
I am interested in buying the 2.2 kW spindle. Does it run much quieter than a 2 hp Porter Cable router? You also mention a pump with a bucket of water. How long until the water is too warm to cool the spindle?

Our spindles have a runout of less than .0001 in, which includes that collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I'm interested in the 1.5 kW (kilowatt) Water Cooled Spindle with Inverter (VFD), I would like to know about the run out of this spindle?

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

Spindles are generally covered up to 1 year after date of purchase. We do not repair them in house, but we do work with our manufacturer to replace defective units. Generally if you have a defective unit covered under warranty, we will issue a replacement.

Click the link to add information to this solution:
what is the warranty period and do you repair these in house? 2.2 kW (kilowatt) Water Cooled Spindle with Inverter (VFD)

Our spindles have a runout of less than .0001 in, which includes that collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to purchase the 2.2 kW water cooled spindle, I would like to know the measured run-out of the spindle?

Spindle comes with 1/4" collet.

"All of our spindles come standard with a 1/4" collet. The 2.2kw, and 4.0kw, can be upgraded to a 1/2" collet with a separate purchase"

Click the link to add information to this solution:
I just purchased the 2.2 kW water cooled spindle. I also ordered a 1/8" collet to go with it, since I assume it comes with a 1/4" collet. Is this correct?

The VFD does come with a manual that details the wiring and connection specifications, terminal features and a list of the parameters. There is no information on how to connect it to Mach3. It does detail the specifications within the parameters and terminal features on the analog input that is used with Mach3 and other control programs.

Click the link to add information to this solution:
I have a water cooled spindle I only need the VFD drive. Does the VFD come with instrutction on hooking the VFD to Mach3?

Absolutely. You can have 1/2" collets used in 2.2kW spindles.

Here is a link for the ER-20 1/2"ID Collet:
https://www.buildyourcnc.com/item/spindle-collet-!5-er20-spindle-collet

Click the link to add information to this solution:
Can the 2.2 KW water cooled spindle be fitted with a 1/2" chuck/collet ?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

A break in process, I'm guessing means if the spindle needs to be turned off for some reason? If so, then no. The water cooled spindle can be run constantly. We run our spindle for very long periods of time.

Additional Information:

Click the link to add information to this solution:
Is there a recommended break in process for a 2.2kw water cooled spindle?

Spindles are generally covered up to 1 year after date of purchase. We do not repair them in house, but we do work with our manufacturer to replace defective units. Generally if you have a defective unit covered under warranty, we will issue a replacement.

Click the link to add information to this solution:
2.2 kW (kilowatt) Water Cooled Spindle with Inverter (VFD) Geven Me My contuy Bangladesh

The blackTooth machine, as it is designed cannot be modified easily as the box within which it is contained also serve as its structure. We are currently designing a special mount for the greenBull (for the 40 watt tube) which will provide 5'x10' or 6'x12' work area and the machine is far less expensive than comparable 4'x8' laser systems. We are also developing a 4'x8' 80 watt system where the tube is in the horizontal orientation. More information can be found in the R&D section.

Click the link to add information to this solution:
I am interested in getting your 40W laser system. How difficult will it be to increase the size to 48" x 48"?

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens, and nozzle. You will also need some mechanical parts and some motors, drivers, and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Call again. Most likely, one of my employees were on the line with another customer at the time you called.

Click the link to add information to this solution:
I am interested in order the redleaf system you talked about for my machine, tried calling and mail box is full, no answer. How do I contact you?

I have not tried connecting a 110V spindle to a 220V VFD; however, the parameters in a 220V VFD do allow changes to the values for the spindle motor. If you do plan on connecting the 110V spindle to a 220V VFD, damages can occur, so I would not recommend it.

With that said, here is the output of an LLM:
Using a 220-volt VFD (Variable Frequency Drive) to run a 110-volt spindle is technically possible, but it requires careful setup to avoid damaging the spindle. Here's what you need to consider:

Check the VFD Specifications: Ensure that the VFD can be set up to output the correct voltage for your spindle. Many VFDs are capable of outputting variable voltages and can be configured via their programming settings to match the voltage requirements of the spindle.

Adjust the Output Voltage: You'll need to configure the VFD to output 110 volts to match your spindle. This is crucial because supplying 220 volts to a 110-volt spindle would likely damage it permanently. Check the VFD's manual for instructions on how to adjust the output voltage settings.

Set the Current Correctly: Besides voltage, make sure the output current does not exceed what your spindle can handle. The VFD should be configured to supply the current at the rating appropriate for the spindle’s power and voltage requirements.

Consult the Manuals: Always refer to the manuals of both the spindle and the VFD. These documents can provide specific guidance on compatibility and settings.

Consider Professional Installation: If you are not familiar with electrical systems or if the manuals do not provide clear guidance, it may be wise to hire a professional. This helps ensure that the setup is done safely and correctly.

By taking these steps, you can safely use a 220-volt VFD with your 110-volt spindle, ensuring it operates efficiently without risk of damage. Just be meticulous with the settings and when in doubt, consult with or hire a professional.

Click the link to add information to this solution:
[77] I have a 110 volt 2.2kw water cooled spindle. Can I run it with a 220 volt VFD?

Absolutely. These spindles do not get bogged down under load like routers will. The speed is regulated and current will adjust with the load.

Click the link to add information to this solution:
Is the "1.5 kW (kilowatt) Water Cooled Spindle with Inverter (VFD)" spindle speed regulated? (Will maintain its speed under load)

Currently in our current stock the collet that work with our 1.5kW spindle 110V/220V, will be the ER-11. Only the 2.2kW spindle uses the ER-20 collet.

Click the link to add information to this solution:
Interested in the 110v 1.5kw spindle and vfd. Need an er16, or preferably an er20 collett. Would this item work.

TIR specifications for the ER-20 collet used on 2.2KW Spindles is .0004 inches.

Click the link to add information to this solution:
Hi, I'm considering buying one of your 2.2 KW water cooled spindles. What is these spindles run out ?