[ Log In ]
[ Register ]
Database maintenance (5/13/2022 and 5/14/2022 between 9:00 pm to 3:00 am EDT). You may experience reduced performance during this time.

Question #: 13459

Question: Is it possible to order just the gantry assembly for the black toe machine?

Current Solution

Yes, You can order, only you need supply the information of the machine.

Respond:

Other Possible Solutions to this Question

  • IS IT POSSIBLE TO MOUNT THE NEW EXTRUDER WHITEANT?

    Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

    Click the link to add information to this solution:
    IS IT POSSIBLE TO MOUNT THE NEW EXTRUDER WHITEANT?

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to add information to this solution:
    WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

  • HOW MUCH MDF IS USED FOR THE BOOK MACHINE COMBO #1

    Three 24" x 48" sheets of mdf is used for the book build or the combo #1 plans and kit.

    Click the link to add information to this solution:
    HOW MUCH MDF IS USED FOR THE BOOK MACHINE COMBO #1

  • WHAT IS INCLUDED IN THE BLACK TOE TO FOOT UPGRADE?

    The gantry sides, gantry bridge parts, two 1/2" rods, two 1/2" ID bearings, two 1/2" ID 12 tooth sprockets, and extra roller chain.

    Click the link to add information to this solution:
    WHAT IS INCLUDED IN THE BLACK TOE TO FOOT UPGRADE?

  • WHAT IS THE SHIPPING COST OF MACHINE TO AUSTRALIA?

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING COST OF MACHINE TO AUSTRALIA?

  • HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

    The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

    Click the link to add information to this solution:
    HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

  • WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to add information to this solution:
    WHAT LEAD TIME CAN EXPECT FOR BLACKTOE SO PICK UP THE MACHINE?

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?

    Yes, the customer will need to sign our NDA (Non Disclosure Agreement) form and send it back to us. We will then send the dxf of the specific updated part of the machine.

    Click the link to add information to this solution:
    CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?

  • THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

    These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

    With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

    Click the link to add information to this solution:
    THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

  • WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

    You can expect a one week lead time for our machines.

    Click the link to add information to this solution:
    WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

  • HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

    I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

    Additional Information:

    Click the link to add information to this solution:
    HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

  • IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to add information to this solution:
    IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

  • IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to add information to this solution:
    IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

  • PARTS LIST FOR THE BOOK MACHINE

    The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

    Click the link to add information to this solution:
    PARTS LIST FOR THE BOOK MACHINE

  • WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

    An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

    Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

  • THICKER MATERIAL OK TO BUILD THE MACHINE?

    Yes, it is ok if the thickness is plus or minus +/- about 2mm.

    Click the link to add information to this solution:
    THICKER MATERIAL OK TO BUILD THE MACHINE?

  • IS DRILL BIT USED IN THE CNC MACHINE?

    The cutting tool is an end mill (it looks like a drill bit). It is a cutting tool that can plunge and cut sideways. That item is not included and is a consumable. You will purchase these very frequently and will have geometry that is very specific to how you apply the cnc machine.

    Click the link to add information to this solution:
    IS DRILL BIT USED IN THE CNC MACHINE?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.