It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

We have a redLeaf and redSprout system available which has all of the CNC electronics and computer system assembled as a plug and play system.

Click the link to add information to this solution:
Can you offer me a combo with motors NEMA17, NEMA23 and NEMA34 and a control box ready for plug and play operation? (this including motor drivers and cables)

From the USB controller, the CP+ and CW+ are connected to the 5V terminal. The CP- is connected to the CP terminal of the driver and the CW- is connected to the CW terminal of the driver.

Additional Information:

Click the link to add information to this solution:
Please explain how to connect 2.5AMP stepper motor driver to USB board. All parts are from your store. Thanks

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler?

We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

Additional Information:
Meant to say pulleys, not pullies.

Click the link to add information to this solution:
Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

I have not hear of this. This cold be an issue with using later firmware, but I have not come across having to cut the trace for the reset enable on the Arduino board.

Click the link to add information to this solution:
Have you heard of the requirement to cut the Reset Enable trace on the Aruduino Mega for a Makerbot Thing-o-matic? Does this apply to the whiteAnt 3d printer? The trace on my Arduino board is definitely connected and I am experiencing issues with connectivity. Please advise.

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

If the motor starts acting rough or is excessively trying to move without physically moving the input shaft. Re-check that your pins are in the correct settings and always set the amps required to the closest needed but not exceeded (ex. required 3.00A, but only having 3.14A revert from using 3.14 and go lower to 2.57A).
Also a software issue that can affect the motor is Config/MotorTunning/(x,y,z)-axis, if you are trying to push your motor to move at a faster rate by modifying the acceleration and velocity could cause your motor to fail if the settings are to high. Lastly out of those two tests, would re-check wiring for continuity lastly.

Additional Information:
Also, even if the wiring was checked thoroughly, re-check the wiring for any chafing from wire ties or any other means of causing a short with two or more of the motor wires.

You can also try swapping the motors from another axis to determine if the cause is derived from the driver or the motor.

Additional Information:
I disconnected the stepper motor entirely except left the yellow and blue wires tied together and the motor still made the sound when manually rotating the shaft. When I disconnected the yellow and blue wire the motor rotated smoothly again, so there must be a short inside the motor. Is there a warranty on the motors you sell?

Click the link to add information to this solution:
The X-axis stepper motor on my BlackToe suddenly started acting up. It is wired bipolar series, and was working great but then in the midst of a cutting operation the stepper started sounding rough- as though one of the phases was shorting out. However, all the connections and wires are in tact. Any ideas what would most likely cause this?

For the NEMA 34 stepper motor with a maximum current of 6 amps, 18 AWG wire would technically be sufficient. According to the American Wire Gauge (AWG) standard, 18 AWG wire can handle up to around 10 amps of current in chassis wiring and around 16 amps in power transmission. If you are considering running a very long length of cable from the driver to the stepper motor, you may want to consider using 16 AWG.

As for the spindle, this wire gauge is well-suited. There are three phase shifts, each at 120 degrees and each conductor is carrying only 1/3 of the power. At 220v, 2200 watts / 220 V = 10 amps. 1/3 of 10 amps is 3.333 amps, so each conductor will be have a load of 3.33 amps.

Click the link to add information to this solution:
[801] Is this enough rating for a Nema 34 motor with max 6 amps? Also what about a 220V 2200Watt Spindle?

If there is play within the motor itself, then that motor may be defective. Call us to provide us more detail on this issue.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
Ins9kru1

Additional Information:
-1 OR 2+486-486-1=0+0+0+1 --

Additional Information:
-1 OR 2+693-693-1=0+0+0+1

Additional Information:
-1' OR 2+890-890-1=0+0+0+1 --

Additional Information:
-1' OR 2+307-307-1=0+0+0+1 or 'HN9afNei'='

Additional Information:
-1" OR 2+88-88-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@mxOzC

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have NEMA 34 motors for a GreenBull 6x12. After 2 weeks of use, my Y axis motor has developed play in the front but not rear of the motor. Is this a motor defect or has something come loose somewhere? Thanks,

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
I'm new to this and was wondering if I connected something incorrectly... I followed the schematics found on this site for wiring. I purchased the heavy gantry kit with the USB power option. All my lights come on and motor shafts resist turning but, I cannot get movement from Mach3. How do I test my equipment to see if I've damaged anything?

You will be fine with using 2 NEMA 23/24 (425 oz-in) and 1 NEMA 34 (651 oz-in) motors with the Woodsmith CNC build with a large heavy router with a 1/2" collet. Specifically, the Woodsmith CNC build uses lead screws for each axis and this will provide mechanical advantage allowing the motors along with the drive mechanics (lead screws) an increase in torque.

Click the link to add information to this solution:
Building the 2'x4' CNC from the Woodsmith plans and want to use a router with 1/2" collet. Will your stepper motor kit with 2 NEMA-23 and 1 NEMA-34 be sufficient for a Bosch 1617 router motor, or will it be too heavy?

Try slowing your feedrate down and increasing spindle RPMs. End-mills will leave a poor finish if you go too fast. Make sure your cutting depth isn't too much. Maybe the endmill or cutter is blunt? Could it be the feed direction of the cutter? Some materials need to be fed in a certain direction.

Click the link to add information to this solution:
MOTOR GOING TWO DIRECTION WHEN JUST PUSH UP. IT WILL GO DOWN AND THEN GOES AGAIN UP WITH THE SAME BUTTON.

Yes, we honor a one year warranty on the NEMA 34 651 oz-in stepper motor.

Click the link to add information to this solution:
Is there a warranty on the NEMA 34 651 Oz-in stepper motors you sell?

Your g-code probably has the feed rate too high. You set the velocity and acceleration in your motor tuning, but g-code may be able to override these values.

Try lowering the feed rate in either your CAM program or in the g-code manually. The feedrate code has an “F” then a number after representing the velocity.

Click the link to add information to this solution:
I'm using Mach3 and I tuning the motors. As is they all seem to jog nicely, smooth and quiet. However when I make moves using gcode they bind and don't move or jerk violently when they do move. What step did I miss?

The NENA 14 motor is paired with this driver and will work very well: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular

Click the link to add information to this solution:
I cannot find a driver for the NEMA 14 Stepping Motor (17 oz-in 1/4" dual shaft) on your site, would something like the Pololu DRV8834 be okay? (I note that the stepper requires 2.7v)