[ Log In ]
[ Register ]

Question #: 13767

Question: Where can I find information on controlling my VFD through Mach4?

Current Solution

The best way to determine how to control your VFD using Mach4 is to read the MAch4 manual found here:
http://www.machsupport.com/wp-content/uploads/2014/05/Mach4%20Installation%20Manual.pdf

You will find that there a a few ways to control the spindle/VFD on your CNC machine or CNC Router.
- The first and easiest is to have your VFD's power controlled by a relay. This will allow your spindle to have on/off control through Mach4 with an output pin.
- The second is to have a controller output a DAC voltage between 0-10 volts to control speed on the VFD/Spindle. There is a termial on the VFD to receive this signal line. The controller will also have an output that outputs a high or low and that can control the on/off on the VFD.
- The third, and more difficult of the three methods is to use a USB to Serial adapter (USB to USART or RS-485). The Computer plugs into the adapter using a USB cable and the adapter uses the RX/TX to connect to the VFD's terminals for communication. This will provide a great amount of control. Mach4 will need a plug-in to make this option work.

Respond:

Other Possible Solutions to this Question

  • WHERE CAN I GET INFORMATION ON INFLUENZA (THE FLU) AND ITS SURVEILLANCE?

    Information regarding influenza surveillance is available October through May from the CDC influenza website at www.cdc.gov/flu/weekly/fluactivity.htm.

    In addition, periodic updates about influenza are published in the MMWR. State and local health departments should be consulted regarding availability of influenza vaccine, access to vaccination programs, information about state or local influenza activity, and for reporting influenza outbreaks and receiving advice regarding their control.

    Click the link to add information to this solution:
    WHERE CAN I GET INFORMATION ON INFLUENZA (THE FLU) AND ITS SURVEILLANCE?

  • I can't seem to find information on spindle control via the breakout board. Can someone point me in the right direction?

    We currently can only control the On/Off of the spindle via Mach 3 and through our Parallel Interface Board. We have the listed instructions on our Parallel Interface Board webpage, will be a easy job that will included 2 wires (18-24g wire will be fine) from your inverter(VFD) to the location of your Parallel Interface Board.

    Parallel Interface Board webpage: https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    In regards to our USB Interface Board, we are currently working on a prototype board that will allow the same On/Off capability with Planet-CNC. Prototype Board currently not available as of yet.

    Click the link to add information to this solution:
    I can't seem to find information on spindle control via the breakout board. Can someone point me in the right direction?

  • I'm about to order your laser cutter , item 279 and a little confused.. in your faq it states you need wire and connectors for assembly, can you be specific on amount and guage of wire or tell me where to find that information?

    The connections between the driver and the breakout board(USB/Parallel)22-24 AWG wire is preference also going from the potentiometer going to LSPS(laser power supply) , now going from the power supply to the drivers/laser power supply 16-18 AWG wire is our preference.

    Click the link to add information to this solution:
    I'm about to order your laser cutter , item 279 and a little confused.. in your faq it states you need wire and connectors for assembly, can you be specific on amount and guage of wire or tell me where to find that information?

  • How can I control my VFD using Mach4 cnc control software?

    The best way to determine how to control your VFD using Mach4 is to read the MAch4 manual found here:
    http://www.machsupport.com/wp-content/uploads/2014/05/Mach4%20Installation%20Manual.pdf

    You will find that there a a few ways to control the spindle/VFD on your CNC machine or CNC Router.
    - The first and easiest is to have your VFD's power controlled by a relay. This will allow your spindle to have on/off control through Mach4 with an output pin.
    - The second is to have a controller output a DAC voltage between 0-10 volts to control speed on the VFD/Spindle. There is a termial on the VFD to receive this signal line. The controller will also have an output that outputs a high or low and that can control the on/off on the VFD.
    - The third, and more difficult of the three methods is to use a USB to Serial adapter (USB to USART or RS-485). The Computer plugs into the adapter using a USB cable and the adapter uses the RX/TX to connect to the VFD's terminals for communication. This will provide a great amount of control. Mach4 will need a plug-in to make this option work.

    Click the link to add information to this solution:
    How can I control my VFD using Mach4 cnc control software?

  • I couldn't find any information about how to mount the "z-axis lead screw in the book" (Build Your Own CNC)

    The details will differ depending on the type of lead screw you use.

    For allthread lead screws, you will need the 1/2" square nut, 1/2" allthread lead screw, two 1/4" screws and nuts to hold the square nut in place, two 1/2" ID bearings, two standard 1/2" nuts, and one coupling hub.

    Attach the square nut to the nut support using the two 1/4" screw and nuts. The bearings will need to be inserted into the seats of the lower and upper part of the z-axis. Insert the lead screw through the top bearing. Use one of the standard 1/2" nuts and start threading it on the allthread screw just below the bearing. Lower the lead screw to the square nut and start to screw the lead screw into the square nut. Continue until the screw is near the lower bearing. Add another standard 1/2" nut to the screw and keep turning the screw until the screw just passes the lower bearing. Add the coupling hub to the top of the screw just above the upper bearing. Turn the lower and upper standard 1/2" nuts until they are snug against the bearing. If the standard 1/2" nuts become loosened, consider adding another nut to each end against the existing nut to keep them in place.

    For 1/2" acme 5 start lead screws, you will need to use an antibacklash nut in place of the square nut. This nut attaches with a flange using two #8 screws and nuts. The standard 1/2" nuts are replaced by clamping collars.

    Click the link to add information to this solution:
    I couldn't find any information about how to mount the "z-axis lead screw in the book" (Build Your Own CNC)

  • I need to determine steps/inch mach3 setup information for my motors and drivers.

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:


    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    L8NiICEm

    Additional Information:
    -1 OR 2+427-427-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+145-145-1=0+0+0+1

    Additional Information:
    -1' OR 2+101-101-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

    Additional Information:
    -1" OR 2+194-194-1=0+0+0+1 --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    TO93cbNY

    Additional Information:
    -1 OR 2+824-824-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+681-681-1=0+0+0+1

    Additional Information:
    -1' OR 2+805-805-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

    Additional Information:
    -1" OR 2+275-275-1=0+0+0+1 --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    -1); waitfor delay '0:0:7' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

    Additional Information:
    2k2XS4cL'; waitfor delay '0:0:15' --

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    g7NWXuig'); waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    XoN629J2')); waitfor delay '0:0:15' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    -5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    -1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

    Additional Information:
    o1WPxXu4'; waitfor delay '0:0:15' --

    Additional Information:
    X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

    Additional Information:
    i2jhQp7d'); waitfor delay '0:0:15' --

    Additional Information:
    xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

    Additional Information:
    IbKvmZZx')); waitfor delay '0:0:15' --

    Additional Information:
    YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:
    -5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@EQr47

    Additional Information:
    -1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    -1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

    Additional Information:



    Additional Information:
    QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@nxzWO

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    vJlQYk5k

    Additional Information:
    -1 OR 2+406-406-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+236-236-1=0+0+0+1

    Additional Information:
    -1' OR 2+914-914-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

    Additional Information:
    -1" OR 2+210-210-1=0+0+0+1 --

    Additional Information:



    Additional Information:



    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

    Additional Information:



    Additional Information:



    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:



    Additional Information:



    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    RO4xZyuD'; waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    n2HpQRHN'); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    hd4dcDEY')); waitfor delay '0:0:15' --

    Additional Information:



    Additional Information:
    -5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    -5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    -1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

    Additional Information:



    Additional Information:
    MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

    Additional Information:



    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:



    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HJ5oY

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    I need to determine steps/inch mach3 setup information for my motors and drivers.

  • I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

    Yes you can. We well the ArtCAM software and modules.

    Click the link to add information to this solution:
    I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

  • where can I find wiring instructions for the Mach3 USB controller?

    You can find all of the wiring instructions for the Mach3 USB controller here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Scroll down until you see the videos. The wiring instructions cover wiring all of the axes, setting up the inputs to sense limit switches, setting up the outputs and how to diagnose the outputs, setting up an external relay to control external devices, and setting up spindle speed.

    Click the link to add information to this solution:
    where can I find wiring instructions for the Mach3 USB controller?

  • I see Artcam modules on your site, can I still get them through you?

    Yes you can. We well the ArtCAM software and modules.

    Click the link to add information to this solution:
    I see Artcam modules on your site, can I still get them through you?

  • Can I use your USB interface board and Mach4 on my 3 axis CNC router?

    The USB interface that we sell only works with planet-cnc software. We will be developing our own USB board and plug-in that will work with Mach4 very soon.

    Additional Information:
    does the mach3 usb interface board work with mach4?

    Click the link to add information to this solution:
    Can I use your USB interface board and Mach4 on my 3 axis CNC router?

  • where can I find the videos to connect the cnc electronics?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to add information to this solution:
    where can I find the videos to connect the cnc electronics?

  • [575] Is there any information on connecting and setting up a pendant.

    I would recommend using a wireless pendant, like here: https://amzn.to/49nAjkg (Affiliate link)

    I use this pendant on my machine and works quite well. If you have communication issues from the pendant to the dongle, there may be too much interference surrounding the dongle, and exposing the internal antenna works well. This is something I needed to do.

    Click the link to add information to this solution:
    [575] Is there any information on connecting and setting up a pendant.

  • I am missing the wiring information for the 1.5kw spindle, my electrician says I need documentation for the 4 prong connector into the VFD

    You can find wiring diagrams and illustrations for the spindle on this page: https://buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd

    This information pertains to the 2.2 kW spindle; however, the wiring is the same for the other spindles as well.

    Click the link to add information to this solution:
    I am missing the wiring information for the 1.5kw spindle, my electrician says I need documentation for the 4 prong connector into the VFD

  • Where can I find the book many of the others have mentioned in their question?

    We do not offer any free plans. We offer the CNC Scratch Build Kit which includes plans to build a CNC machine from scratch. You can find more information about this by clicking on this link https://buildyourcnc.com/cnckitintro.aspx

    Additional Information:
    WTF!! It says right on your utube page free plans available. I'll paste it from Utube right here.(DIY CNC Router for Under $900 - Free Plans Available) Very misleading, I spent a lot of time looking for this stuff and am lucky I found this because apparently none of its available for free. Very misleading, dishonest sales tactics. I'm sure you've made money conning honest people out of there money but your not gonna get shit from me. After reading what other people here have written, and the fact that you lie about the cost, at least on UTUBE, It is clear your a liar and a piece of shit. carry on though by all means and continue making money being a liar.

    Additional Information:
    So maybe you should edit your YT post that says you DO have free plans?

    Click the link to add information to this solution:
    Where can I find the book many of the others have mentioned in their question?

  • THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

    To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

    Additional Information:
    MUAR-QVXU-CAYW-CBWQ


    Additional Information:
    MUIS-RQPB-PTHB-QTTB

    Additional Information:
    MUIH-EERP-IADB-TRIP

    Additional Information:
    9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

    Additional Information:
    Key: LUQR-BQYI-SCEW-QVBT

    Additional Information:


    Additional Information:
    after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

    Additional Information:
    MUJR-BISM-KRDN-KKER
    056971

    Additional Information:
    0561234

    Additional Information:
    MURL-QPQU-EGBJ-FNMB

    Additional Information:
    MUCE-LFMQ-WBCW-MLHO

    Additional Information:


    Additional Information:
    LUTA-ADVJ-FXTW-FBCE

    Additional Information:
    LUTA-ADVJ-FXTW-FBCE

    Additional Information:
    looking for registration key for MUUK-IBTW-ECTL-CJWD

    Additional Information:
    MUXO-PIYY-KNHD-RKLY

    Additional Information:
    MUUE-YYCR-FCIC-VATK

    Additional Information:
    MUUE-YYCR-FCIC-VATK

    Additional Information:


    Additional Information:
    MUEY-YLJU-OBRR-LJBV

    Additional Information:
    MUSP-JFDV-EKGQ-OVLW

    Additional Information:
    MUSP-JFDV-EKGQ-OVLW

    Additional Information:


    Additional Information:


    Additional Information:
    MULY-XRYF-BBDN-FBWP

    Additional Information:


    Additional Information:


    Additional Information:
    how to generate activation code richauto a11

    Additional Information:
    MUJC-LNIL-EOHS-YKNQ

    Additional Information:
    sdfd

    Additional Information:
    m l

    Additional Information:
    MUXC-RWKB-PKAL-HGNN

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Additional Information:
    57625YY60Y7Y30X5

    Click the link to add information to this solution:
    THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

  • I need wiring diagram for motor to driver to usb motion card. I cannot find diagram. I have been unable to get information for a week.
  • I look on your site and find nowhere to download Mach 3, Where is it?

    I just added a link to the Mach3 license page on our site:
    https://www.buildyourcnc.com/item/control-SOFTWARE-mach3

    Click the link to add information to this solution:
    I look on your site and find nowhere to download Mach 3, Where is it?

  • What settings does I use for controlling the spindle in StepCon/Linuxcnc?

    LinuxCNC has excellent documents; however, I would like to offer our help in case you don't understand the information on that page. So, please use this FAQ (Question #: 13233) to state your questions by submitting additional information below.

    The LinuxCNC spindle control page is found here: http://linuxcnc.org/docs/html/examples/spindle.html

    Additional Information:
    After reading the LinuxCNC page my first questions would be can the spindle be controlled by PWM signal? Also, what pin on the parallel port would I set to Spindle Enable and FRW?

    Additional Information:
    To connect your computer to the VFD, use a USB to RS-485 interface. RS-485 is just a serial interface protocol that uses standard 0 to +5 voltage TTL signal levels for communication (as opposed to RS-232 which uses -12v and +12 for signal level changes).

    Get a high quality interface to reduce any issues during the process. The VFD should have two terminals labeled RS+ and RS-. The USB to RS-485 adapter should have this labeled on it as well so the connections should be relatively straight forward.

    In the VFD parameters:
    PD001: 2 to accept RS485 commands
    PD002: 2 to accept frequency comands
    PD163: 1 to RS485 slave address:1
    PD164: 1 RS485 baud rate 9600
    PD165: 3 8bit, no parity, 1 stop bit

    Make sure LinuxCNC is also set accordingly:

    The PIN14 and PIN16 in the stepconf wizard should be set to unused because you don't want LinuxCNC to be outputting unnecessary signals.

    In the options step of the stepconf wizard:
    - Check the Include Halui user interface component.
    - Check the Include custom PyVCP GUI panel.
    - Check Spindle speed display

    You will want to edit the custom.hal text file located in the folder that was created from the stepconf wizard. Add these following lines:
    loadusr -Wn vfd hy_vfd -n vfd -d /dev/ttyUSB0 -p none -r 9600
    net spindle-cmd-rpm-abs => vfd.speed-command
    net spindle-cw motion.spindle-forward => vfd.spindle-forward
    net spindle-ccw motion.spindle-reverse => vfd.spindle-reverse
    net on motion.spindle-on => vfd.spindle-on

    The dev folder in linux is typically used for interfacing devices and peripherals to the computer as these devices are communicated by simple memory addresses and these files are linked directly to these addresses.

    Under the custom_postgui.hal file, change this line:

    from: sets spindle-at-speed true
    to: net spindle-at-speed => cfd.spindle_at_speed

    and add the line:

    setp vfd.enable 1

    When you start LinuxCNC, you will a spindle section with the reverse and forward buttons, a stop button and - and + buttons. Use these buttons to conform that the spindle is functioning properly. The spindle speed indicator in LinuxCNC will show the spindle speed and you can confirm that this is equal to the speed indicated on the VFD.


    Credit for this helpful information goes to:


    Additional information was also added by us to provide a better understanding.

    Additional Information:
    linuxcnc利用MACH3 接口板 BL-MACH-V1.1的一路经光耦隔离的 0-10V 模拟电压输出,可以控制具有相应模拟接口的变频器,控制主轴转速。输出口为 P1 口,如何利用这个p1口与变频器进行接线来控制主轴转速,并对hal文件配置代码进行书写

    Click the link to add information to this solution:
    What settings does I use for controlling the spindle in StepCon/Linuxcnc?

  • I ordered a 2.2kW spindle as a guest on March 3rd. How long does it take for you to provide shipping information?

    I will check

    Additional Information:
    The license was purchased and the developer is sending you the license shortly.

    Click the link to add information to this solution:
    I ordered a 2.2kW spindle as a guest on March 3rd. How long does it take for you to provide shipping information?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.