The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

This book offers an excellent platform upon which to learn CNC technology and fabrication no matter how old the book is. If you are new to CNC routers, I wuld highly recommend this book. The book will provide you with the plans and the knowledge to build a capable entry level CNC router and you will learn the fundamentals necessary to become successful with fabrication, maintaining the machine (and almost any machine), and how these complex CNC routers work.

The machine kits on this website were created as an upgrade or alternative to the book CNC router build. Specifically the blackToe CNC Router: https://www.buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I bought the book that you co-authored (Build Your own CNC) a few years ago. Its not till now that I’ll be able to start the project. Are all the parts still available? The book is about 8 years old now so I’m wondering if its still worth building that design? (I don’t see a newer version of the book)

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

This video should provide enough guidance to understand the PWM signal on the Mach3 USB controller:

Click the link to add information to this solution:
[575] Hello, I'm wondering if you can provide advice how to wire this USB board where for spindle I would like to use chinese servo motor and driver (TD3) - speed control mode. Especially how to connect - AVI, ACM and 10V (24V is clear). I am still not sure how to power on and off spindle itself. Thank you in advance. Vaclav

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

The best choice would be a type K thermocouple.

Click the link to add information to this solution:
I have the hot end listed on your site here :http://buildyourcnc.com/item/3D-Printer-Component-extruder#prettyPhoto what thermocouple or thermistor do I need for the hot end? it is not clear my original order was the email jeremy.adair@compassauto.net. please let me know what I need to buy. thanks.

Yes, we can ship to the UK. We ship there often. The shipping time will be based on the selection you make in the shopping cart when you press the calculate shipping button. We work with many universities and we can process the order according to your administration's needs.

Here is our canned response for general shipping questions:
You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
I am running a research project at Bath University in the UK based on desktop CNC machines and their potential use in the department of engineering. Will you guys ship to the UK & what is the estimated time? Thank you.

Sorry the trimmer snapped off. You are planning to do exactly what we are going to do in the next revision. The potentiometers/trimmers are 10k ohm.

Click the link to add information to this solution:
The vacuum regulator trimmers, do you know the part number and brand name for those as I had one snap off trying to use it. I would like buy a trimmer adjustment tool for it as the screwdriver is not working for me and also lookup the specs for it in case I want to convert it to a potentiometer.

The E.Lu.5 Error code on your VFD is related to Low Voltage.

The recommended action is:
- 1. Check whether the input voltage is normal. (the voltage from the wall/breaker to the VFD)
- 2. Check whether there is a sudden change in load.
- 3. Check whether there is any phase missing.

Unfortunately, these three recommended actions will probable require an electrician to test the line going into the VFD.

Additional Information:

Click the link to add information to this solution:
I have wired up my 110v VFD and my 2.2Kw spindle and I get an E.Lu.5 code. My wiring is correct and the parameters are set to those for the VFD according to your website I found in a previously answered question from someone here. Any help would be greatly appreciated, thank you!!

Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.

Our breakout board, does require 5v to operate the correct voltages coming in from the drivers and also coming in from your computer, now the 5V will be supplied by the USB connection, so no external power supply is needed, for either our USB/Parallel breakout board.

Click the link to add information to this solution:
Just for general knowledge. If a spindle gets i.e. 240VAC, and the drivers 36-50VDC for power, why do you need 5VDC for the Breakout Board (BlueBrew)? Is it only for the relay? I think I've seen other BoB's working without power supply, or am I wrong?

If you already have a Mach3 license, you don't need to purchase another one. The license is connected to you rather than the computer. Mach4 is licensed to the computer, but you are able to have multiple computers for each license, and can be switched from one computer to another.

If you purchased the license from me, you can call (make sure to leave a voicemail), or email to get a re-issued license.

Click the link to add information to this solution:
[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine. I will have to buy a new license for the Mach 3 so will need to get the interface board I have to talk to MAch 3. Can I get just the disc or is there a place I can download what I need?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
Limit switches for axis. The print shows that you can wire the limits either n.o. or n.c. so if this is correct I would need to tell the board in the software how to look at these limits, I'm either going to get an input or loose an input depend on how i wire it.

With our blackTooth kit, if you were to go with our lowest cost machine being $1700. With the parallel breakout board the best new beginner programs you can use, would be Mach 3 and ArtCAM, since it is a good program for beginning users.

Now if you feel a little comfortable with CAD/CAM, I would recommend CAMBAM and is a good overall software since it has a large design screen which allows you to view your design more clearly.

Additional Information:


Additional Information:
I want to avoid the Parallel Port option and go with USB. In that case, is Planet-CNC Software, and ArtCAM the best combination? Does Planet-CNC do the same thing as Mach 3 only with different physical ports?

Click the link to add information to this solution:
I'm interested in buying your blacktooth laser engraver for cutting out inlays on woodworking projects. I am new to laser engraving/cutting, and CAD. What is the simplest beginning software setup available to allow me to cut 2D shapes and letters for inlay work?

I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

The greenLean vertical CNC is stable enough to handle large-scale production on a daily basis. We use 3/4" MDO plywood, which is equivalent to about 19mm. The gantry is designed to hold a 2.2kW Spindle, with a maximum of 24,000 RPM.

Click the link to add information to this solution:
Hello. I like your vertikal router. Is then router stabil enogh for the need of a Carpenter? Are you using 21mm Plywood or 21mm MDF. What type of spindel (KW) is maximum allowed and whatbis the maximum feed (6mm cutter) in oak. Thank you, Veit

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.