[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14599

Question: How to output 0-10V to AVI+AVI-?

Current Solution

In the motor outputs, the spindle should be set to pin number 3. This is also the output terminal number 3 (O3). In Mach3: Select [Config], select [Ports and Pins], and select [Spindle Setup] page in the popup dialog box. In the Motor Control box, check Use Spindle Motor Output and select PWM Control.

[Use spindle motor output] is checked, Mach3 will automatically enable the spindle motor output pin. Click OK when the pop-up happens that will say "Spindle Motor has now been enabled. Ensure you set its pinouts.

Next, select the Motor Outputs tab. At the line where [Signal] is [Spindle], check [Enable], modify [Step Port] to "3", modify [Step Pin#] to "3", and specify O3 as Is the output terminal of the PWM.

Press [OK] button to save. Connect the indicator (refer to the previous section) to O3 for debugging. When the program "M3"executed is, O3 output signal can be seen.

The AVI+ and AVI- corresponds to the ACM and AVI terminals.

Additional Information:
In the answer setting, 0-24V is output to out3, but not to AVI+/ACOM.
Of course, 10V is given to the 10V terminal of the board.

Respond:

Other Possible Solutions to this Question

  • How do I connect the outputs on the Mach3 USB motion card?

    A 24V connection to the USB motion card is only needed if you are using limit switches (inputs), powering the spindle/VFD speed and direction, and for the outputs, for powering other devices (mist, coolant, etc.).

    If you are using a VFD (Variable Frequency Drive, also called Inverter) for a spindle, they typically have a 24V out terminal that can be used with our USB motion card. If you are not using a spindle/VFD (we highly recommend one), then you will need to purchase a 24v power supply to power that side of the board.

    The outputs mentioned above are to connect to external devices and will require a relay (a mechanical switch that is controlled by a digital signal). This mechanical switch can turn on a device like coolant and mist, or even a router, if you are using one. A relay is required to turn on these devices because the devices are typically higher voltage, like mains (110v or 220v). So, a relay can turn on or off a high voltage device with a lower voltage (24v) signal.

    Click the link to respond:
    How do I connect the outputs on the Mach3 USB motion card?

  • How do I connect the outputs on the USB motion card for Mach3?

    A 24V connection to the USB motion card is only needed if you are using limit switches (inputs), powering the spindle/VFD speed and direction, and for the outputs, for powering other devices (mist, coolant, etc.).

    If you are using a VFD (Variable Frequency Drive, also called Inverter) for a spindle, they typically have a 24V out terminal that can be used with our USB motion card. If you are not using a spindle/VFD (we highly recommend one), then you will need to purchase a 24v power supply to power that side of the board.

    The outputs mentioned above are to connect to external devices and will require a relay (a mechanical switch that is controlled by a digital signal). This mechanical switch can turn on a device like coolant and mist, or even a router, if you are using one. A relay is required to turn on these devices because the devices are typically higher voltage, like mains (110v or 220v). So, a relay can turn on or off a high voltage device with a lower voltage (24v) signal.

    Click the link to respond:
    How do I connect the outputs on the USB motion card for Mach3?

  • WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

    U - Pin1
    V - Pin2
    W - Pin3
    Pin4 Dead

    Additional Information:
    My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

    Click the link to respond:
    WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

  • I'm trying to get the planet-cnc mist, coolant and spindle output to work. It's showing no voltage when I test

    On the Planet-CNC board, the Mist, Spindle and Coolant outputs will require a relay to switch on those devices. Test one of those terminals with a multi-meter (Mist, Coolant, or Spindle). Each of these terminals have a GND next to the terminal for the device.

    Test the voltage across the GND to the terminal with the arrow that you want to test. Go to the software and click on the device you want to test (mist, coolant or spindle) and note the voltage. If no voltage is output then check under the board to where the terminals are soldered. Re-test the terminals across the solder joints rather than the terminal block wire inputs. If you get a voltage, then there is a problem with the terminal block. If you don't get a voltage, then the board is not functioning properly.

    Additional Information:
    I activated the output signal.. I did the tests indicated and I did not get voltage. I heated the welds of the three outputs and now works coolant but no mist or spindle, what should I do?

    Additional Information:
    There are probably cold joints on the board at the chip or the resistors on the traces for those terminals. You can send the board back to us and we will repair and test the board.

    Click the link to respond:
    I'm trying to get the planet-cnc mist, coolant and spindle output to work. It's showing no voltage when I test

  • What output pins on your BOB are used to control the SuperPID?

    Yes, you can use any two of the output terminals of the breakout board to control the SuperPID closed loop router controller (a diagram is not needed with these instructions).

    One output terminal will be used as an on/off (1/0 or 5v/gnd) that will be invoked with the M3/M4/M5 M-codes in your g-code instructions.

    The other terminal will be connected to either another 5v/gnd signal to control speed for 5000/20000 rpm or for PWM output (recommended) for proportional speed control.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to respond:
    What output pins on your BOB are used to control the SuperPID?

  • Can I run two stepper motors off the same axis output on the USB controller?

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

    Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
    Slave 1 - X-Axis
    Slave 2 - Y-Axis
    Slave 3 - A-Axis
    Slave 4 - B-Axis
    Etc...

    Click the link to respond:
    Can I run two stepper motors off the same axis output on the USB controller?

  • what is the wavelength of the laser output?

    The CO2 laser tubes that we sell have an output light wavelength of 10500 nm (nanometer). Our goggles provide protection for this wavelength of light.

    Click the link to respond:
    what is the wavelength of the laser output?

  • On your BOB, which pin outputs a PWM signal?

    Yes, you can use any two of the output terminals of the breakout board to control the SuperPID closed loop router controller (a diagram is not needed with these instructions).

    One output terminal will be used as an on/off (1/0 or 5v/gnd) that will be invoked with the M3/M4/M5 M-codes in your g-code instructions.

    The other terminal will be connected to either another 5v/gnd signal to control speed for 5000/20000 rpm or for PWM output (recommended) for proportional speed control.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to respond:
    On your BOB, which pin outputs a PWM signal?

  • HOW LONG DOES IT TAKE TO SHIP

    Unfortunately I am not able to give an estimate of shipping time. This is because there are multiple shipping options, Some of them cost more than others, but ensure the package arrives in a certain number of days. Others do not give a number of days, and many factors could change the length of shipping time, such as weather, or busy season. It would be best to choose an option you are comfortable with the price of, and then Google search the typical times it takes for that option to get to you, or call the shipping company and request that estimated time from them.

    Additional Information:

    Click the link to respond:
    HOW LONG DOES IT TAKE TO SHIP

  • how to contact you via email

    You can find all the ways to contact us by clicking on the contact us link at the footer.

    Our email is customerservice@buildyourcnc.com
    Our phone number is 281-815-7701

    Click the link to respond:
    how to contact you via email

  • HOW LONG FOR ME TO BUILD IT?

    The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

    Click the link to respond:
    HOW LONG FOR ME TO BUILD IT?

  • How to wire drivers to pokey57

    Here is the list of videos that I created to show how to connect pokeys57CNC interface. I go over connecting the Pokeys57CNC to stepper motor drivers, connecting limit switches, connecting to the VFD (variable frequency drive) for the spindle control and even conect a laser triggering.

    https://www.youtube.com/playlist?list=PL6PplMTH29SETy_UYRcKQDspJOin_lzDB

    Click the link to respond:
    How to wire drivers to pokey57

  • HOW CAN ENHANCE THE BLACKTOOTH?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to respond:
    HOW CAN ENHANCE THE BLACKTOOTH?

  • How to setup RAID on Ubuntu

    1) Make sure to setup Primary partition:

    Primary
    Beginning of this space
    Ext4
    Mount point: /
    and Swap partition:

    Logical
    Beginning of this space
    Swap area using "Something Else"

    2) get and install updates and upgrades

    sudo apt-get update
    sudo apt-get upgrade

    3) get raid software

    sudo apt-get update
    sudo apt-get install mdadm

    4) setup RAID

    a) if raids haven't been setup:
    sudo mdadm --create /dev/md0 --chunk=256 --level=0 --raid-devices=2 /dev/sda /dev/sdb

    b) if raids are setup, but just have to be reassembled:
    sudo mdadm --assemble /dev/md0 /dev/sda /dev/sdb

    or

    mdadm --assemble --scan

    Click the link to respond:
    How to setup RAID on Ubuntu

  • how connect inverter to usbcard

    We will answer your question but need more specifics as to what you are referring to. Please add additional information and we will respond.

    Additional Information:


    Additional Information:
    Hi, i'm in France, I have an usb breakoutboard from you and a red fly box
    A 2,2 spindle with the correct inverter.
    I just wan't to know if it's possible to drive the spindle from Mach 3,and if it is, how connect the usb card to the inverter which is connected to the spindle.
    Do I need another driver or any interface card?

    Additional Information:


    Additional Information:
    Sorry, I mean with planet cnc not mach3

    Click the link to respond:
    how connect inverter to usbcard

  • BLACKTOE REQUIRED HOW MUCH CABLE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE REQUIRED HOW MUCH CABLE

  • how to wire limit switches

    The parallel breakout board allows for 4 input connections. Each input connection can have an unlimited number of switches, but if you need to separate the switch circuit for, say, all of the home switches, you can use another input pin. There is no need to add another breakout board to add more switches unless you need to use the input pins for totally unique conditions that may or may not be related to CNC functions.

    Customer response:
    To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on?

    Plus, I have a SuperPID. Another pin?

    Additional answer:
    You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

    The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

    The GND terminal can be doubled up.

    Additional Information:
    how about a diagram to reference showing the pin-out to use

    Here is the diagram for the parallel breakout board (pins 10 through 13 are used for input):

    The circuit is from the GND to the input

    Here is the diagram for the Mach3 USB board (pins I1 through I4 are used for input):
    https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
    The circuit is from the V- to the input pin

    Click the link to respond:
    how to wire limit switches

  • HOW TO CONNECT THE INVERTER WALL?

    Input to VFD:
    240V Active - R
    240V Neutral - S
    Ground - E

    Click the link to respond:
    HOW TO CONNECT THE INVERTER WALL?

  • HOW DO I SET UP MY MOTOR DRIVERS?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Click the link to respond:
    HOW DO I SET UP MY MOTOR DRIVERS?