If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I HAVE FOLLOWED ALL THE "CNC ELECTRONICS 1 - 9" VIDEOS AND I'M USING ALMOST EXACT SAME COMPONENTS (MOTORS RUN SOUND GOOD) BUT MOTORS ARE RUNING VERY HOT IN JUST 15MIN WITH NO LOAD DONE SOMETHING WRONG OR DO STEPPERS HOT?

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

The term cGy (centigray) is a unit of absorbed dose of ionizing radiation such as x rays or gamma rays. Cell phones do not emit ionizing radiation. They emit nonionizing radiation, namely radiofrequency (RF) energy. Absorption of nonionizing radiation in the body is measured in terms of the specific absorption rate (SAR) in units of watts per kilogram. Both ionizing and nonionizing radiation are forms of electromagnetic energy. The difference is that ionizing radiation has sufficient energy per photon to cause ionization of molecules. Nonionizing radiation does not. It is the ionizing effect of ionizing radiation that has been linked to increased risk of cancer. For more information on cell phones and health check out a Medical College of Wisconsin website. For more information on ionizing versus nonionizing radiation check out a University of Michigan website. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

Click the link to add information to this solution:
MY QUESTION THAT KNOW CANCER CAN BE CAUSED WHEN OUR BODY EXPOSED TO DOSES OF 50 CGY OR HIGHER. WHAT DOES STAND FOR? DO EMIT?

Everyone always assumes they are doing something wrong when a plant fails to perform to their expectations. Grapes need pollinator activity to set viable fruit, but there is a shortage of bee activity throughout the country. When the flower cannot be pollinated by bees, the resulting fruit usually atrophies. It is not your fault, just a shortcoming in nature's network.

Click the link to add information to this solution:
I PLANTED SEVERAL CONCORD GRAPE VINES DURING THE PAST FEW YEARS. GOT A COUPLE OF VERY TINY BUDS THIS YEAR, BUT THEY DRIED UP AND DIED. WHAT AM DOING WRONG?

You should use the linuxcnc.org site and click on the download menu item. They have an EU mirror as the main download option.

Click the link to add information to this solution:
AM STRUGGLING TO DOWNLOAD THE LINUX EMC2 FREEWARE. MY GET INTERRUPTED AT LAST MINUTE. IS THERE ANOTHER WAY OR PLACE WHERE COULD MAYBE TRY IT FROM?

When the z axis is going down, the laser turns on. When the z axis is going up, it turns off. The z axis directions is only a signal that is either 5v or 0v. That determines the direction. In vectric, you will need to set your machining operations with a very very small depth so the time it takes to get to its final depth is a very short time.

Click the link to add information to this solution:
AM NOT SURE HOW TO SET THE Z AXIS TURN ON/OFF LASER WHEN CREATE CODE. KNOW THAT ITS TYPICALLY Z-AXIS MOVEMENT DOES THIS - BUT YOU DONT SHOW ANYTHING HOOKED UP IN PLACE OF AXIS.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

I have not come across this problem, but there may be USB, or firmware issues that you are experiencing. I would recommend going on the polabs website and using their support center (https://support.poscope.com/)and posing that question to them. Also, have you tried the ethernet port as an alternative to see if that helps?

Here is the response from an LLM:

Check USB Cable and Port: Start with the basics. Sometimes this error is due to a poor USB connection. Ensure you're using a high-quality, shielded USB cable and that it's plugged into a USB port directly on your computer, not through a hub. If possible, try a different USB port or a different cable to rule out any issues there.

Update Firmware and Software: Ensure that both your PoKeys57CNC firmware and the Mach4 software are up to date. Firmware updates for your PoKeys board might include optimizations or fixes that address connectivity issues.

USB Polling Rate: This error can also arise from the USB polling rate setting in the PoKeys configuration software. It might be set too high for your system's ability to handle it. Try lowering the polling rate and see if that resolves the error.

Computer Performance: Check your computer’s performance. If it’s running several heavy applications simultaneously, it might not be able to process signals from the PoKeys board fast enough. Try closing unnecessary applications or consider using a dedicated machine if your current setup is too taxed.

Mach 4 and PoKeys Plugin Configuration: Dive into the Mach 4 plugin configuration for PoKeys. Ensure that all settings are correctly configured as per the manual. Incorrect settings might lead to communication bottlenecks.

Connection Quality and Interference: Consider any potential interference sources near your CNC setup or computer. Electromagnetic interference from large motors, other electronics, or long cable runs can affect communication quality. Try rearranging your setup to minimize interference.

Consult Documentation and Support: If the issue persists, consult the detailed documentation provided by PoKeys or reach out to their customer support. They can offer more specific advice based on the latest product updates or known issues.

Click the link to add information to this solution:
I HAVE FOLLOWED YOUR YOUTUBE VIDEO ON SETTING UP THE POKEYS 57CNC BOARD BUT WHEN OPEN MACH 4 GET A ERROR MESSAGE CONNECTION IS TO SLOW

BYCNC Response:
Please send a photo of the bolts and assembly so we can determine the problem. Thanks.

User Response:
The holes on the Dremel holder are 0.442" and the bolt heads are 0.483". Picture will be sent. In the picture note that the left bolt has been ground down.

BYCNC Response:
You were sent incorrect fasteners due to a vendor change. We will be shipping the correct parts to you immediately, and thank you for letting us know about this mistake.

Click the link to add information to this solution:
I JUST RECEIVED MY WHITE ANT AND STARTED TO DO SOME BASIC ASSEMBLY. NOTICE THAT THE 1/4 X 20 BOLTS WITH PHILLIPS HEAD NOT FIT IN NOTCHES CUT FOR THEM - INSTANCE, ON DREMEL MOUNT. AM SUPPOSED BUY DIFFERENT HEADS, GRIND ALL DOWN, OR ROUTE OUT BIGGER NOTCHES. 3" BARELY Z-AXIS MOTOR

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

Physical size of the subject affects the fraction of the total radiofrequency energy that is absorbed in the body. To account for this known effect, the maximum permissible exposure standards for radiofrequency energy were set for the worst-case condition, that is assuming the body size for maximal absorption at a given frequency. Thus the maximum permissible exposure standards are fully protective for bodies of different sizes. For more detailed information, see the answers and the cited references to questions 79, 109, 694, and 893 under the Nonionizing Radiation section of the Health Physics Society Ask The Expert Web page. Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
WHAT EFFECTS OF CELL PHONES WILL THERE BE ON YOUNGER PEOPLE OPPOSED TO OLDER PEOPLE? THE AGE OR STATE DEVELOPMENT EFFECT DANGERS A PHONE?

VFD settings........
1) To program the VFD, wire it up, plug it in. It takes several seconds to come to life.

2) Push the PRGM button to enter programing mode.

3 )Push the SET button. The display will read PD000.

4) If you push the SET button again, it will display the present setting of PD000.

5 )By pushing the up or down arrows, you can change the setting to whatever it needs to be. (This is just an example. PD000 needs no changes)

6)Push the SET button again to lock in the setting of PD000 and advance to the next number, in this case, PD001.

7) Push the SET button and it will display the present setting of PD001. Again, use the up and down arrows as necessary to set PD001, then push SET again to lock it in.

Note: You can also scroll through the PD numbers with the up and down arrows.

8) make all settings this way.

9) by pushing the SET button you can scroll through the settings. First push of SET moves to the next number, second push displays it's setting, third push moves to the next PD number.

Note- If you take too long, it will leave the programing mode on it's own. If it does, just push PRGM again to return to programing mode. Then press SET and continue what you were doing.

10) Start with PD013. Set it to 1, which returns the settings to the factory settings.

11) Then set PD005 to 400, PD004 to 400, and PD003 to 400 IN THAT ORDER.

12) Then set the following: PD041=8, PD144=3000

13) Set PD209=50

That's it for the programing. You should get 24000RPM when you push RUN.

Click the link to add information to this solution:
I JUST RECEIVED A REPLACEMENT SPINDLE (2.2KW 220V). HOWEVER, WHEN ATTEMPTED IT USE THE NEW SPINDLE, WOULD ONLY REACH 1500 RPM. IS THERE SOMETHING NEED TO CHANGE ON CONTROLLER?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

Yes. Influenza vaccine commonly contains three influenza vaccine virus strains; two for A viruses and one for a B virus which are prepared based on circulating viruses from the previous influenza season. Infection from one virus type does not confer immunity to other types and it would not be unusual to have exposure to more than one type during a typical influenza season. By all means, vaccinate this person!

Click the link to add information to this solution:
IF AN UNVACCINATED PATIENT HAS JUST RECOVERED FROM A DIAGNOSED CASE OF INFLUENZA COMES INTO OUR CLINIC, SHOULD WE VACCINATE HIM?

You can determine if the area is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

Yes, you can use lubrication, like 3-in-1 oil to make it a bit easier. You will need to run it up and down to break it in.

Additional Information:

Click the link to add information to this solution:
THE LEAD SCREW IS VERY HARD TO TURN. BACKLASH BUSHING SEEMS BE TOO TIGHT AND BINDING ON SCREW. DO IT NEED LUBRICATION OR DID DAMAGE NUT WHEN INSERTING SCREW?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
I AM HAVING TROUBLES FINDING THE PD PROGRAM, HAVE BUT IT DOESN'T SHOW EVERYTHING NEED TO PROGRAM MY VFD. ANY HELP WILL BE APPRECIATED...